Dentine bond strength of a composite resin polymerized with conventional light and argon laser

Measurement of solubility and water sorption of dental nanocomposites light cured by argon laser

Different parameters used for photoactivation process and also composition provide changes in the properties of dental composites. In the present work the effect of different power density of argon laser and filler loading on solubility (SL) and water sorption (WS) of light-cure dental nanocomposites was studied. The resin of nanocomposites was prepared by mixing bisphenol A glycol dimethacrylate (Bis-GMA) and triethylene glycol dimethacrylate (TEGDMA) with a mass ratio of 65/35. 20 wt.% and 25 wt.% of nanosilica fillers with a primary particle size of 10 nm were added to the resin. Camphorquinone (CQ) and DMAEMA were added as photoinitiator system. The nanocomposites were cured by applying the laser beam at the wavelength of 472 nm and power densities of 260 and 340 mW/cm(2) for 40 sec. Solubility and water sorption were then measured according to ISO 4049, which in our case, the maximums were 2.2% and 4.3% at 260 mW/cm(2) and 20% filler, respectively. The minimum solubility (1.2%) and water sorption (3.8%) were achieved for the composite containing 25% filler cured at 340 mW/cm(2). The results confirmed that higher power density and filler loading decreased solubility of unreacted monomers and water sorption and improved physico-mechanical properties of nanocomposites.

Argon ion laser curing depth effect on a composite resin

The aim of this study was to define optimal power settings as well as curing time associated with evaluating the curing depth of a composite resin as a function of Vickers hardness. The tests were performed with a hybrid composite resin cured with a halogen lamp and argon ion laser, with different exposure times and power settings. The composite resin bulk technique was used using a black polypropylene matrix with thicknesses ranging from 1 to 4 mm and Vickers microhardness was measured on the opposite surface of the light activation. ANOVA and Tukey statistical tests were used. The results showed that the groups activated by the laser for 20 s, at 200 and 250 mW, did not present statistically significant differences regarding the halogen lamp with 1 mm thickness, but the halogen lamp showed better results with thickness values more than 2 mm (p < 0.05).

Evaluation of curing light distance on resin composite microhardness and polymerization

This study evaluated the influence of the curing tip distance on cure depth of a resin composite by measuring Vickers microhardness and determining the degree of conversion by using FT-Raman spectroscopy. The light curing units used were halogen (500mW/cm2) and LED (900mW/cm2) at a conventional intensity and an Argon laser at 250mW. The exposure time was 40 seconds for the halogen light, 20 seconds for the LED and 20 and 30 seconds for the Argon laser. The curing tip distances of 0, 3, 6 and 9 mm were used and controlled via the use of metal rings. The composite was placed in a black matrix in one increment at a thickness of 1 mm to 4 mm. The values of microhardness and the degree of conversion were analyzed separately by ANOVA (Analysis of Variance) and Tukey test, with a significance level set at 5%. Correlations were analyzed using the Pearson test. The results obtained conclude that greater tip distances produced a decrease in microhardness and degree of conversion values, while increasing the resin thickness decreased the microhardness and degree of conversion values. A higher correlation between microhardness and the degree of conversion was shown. This study suggests that the current light curing units promote a similar degree of conversion and microhardness, provided that the resin is not thicker than 1 mm and the light source is at a maximum distance of 3 mm from the resin surface.

Photopolymerization of dental resin as restorative material using an argon laser

The effect of the 488-nm wavelength of argon laser at different power densities and irradiation times on the degree of conversion (DC), temperature rise, water sorption, solubility, flexural strength, flexural modulus, and microhardness of bisphenole A glycol dimethacrylate and triethylen glycol dimethacrylate with a mass ratio of 75:25 was studied. Camphorquinone and N,N'-dimethyl aminoethyl methacrylate were added to the monomer as a photo initiator system. The DC% of the resin was measured using Fourier transform infrared spectroscopy. The maximum DC% (50%), which was reached in 20 s, and temperature rise because of the reaction (13.5 degrees C) were both higher at 1075 than 700 mW/cm(2). Water sorption and solubility were measured according to ISO4049, which in our case were 23.7 and 2.20 microg/mm(3) at 1075 mW/cm(2), respectively. A flexural modulus of 1.1 GPa and microhardness of 19.6 kg/mm(2) were achieved above the power density. No significant difference was observed (i.e., p>0.05) for water sorption and flexural strength at 700 and 1075 mW/cm(2).