Influence of different shades and LED irradiance on the degree of conversion of composite resins

Toxicity and cytokine release from human dental pulp stem cells after exposure to universal dental adhesives cured by single peak and polywave LEDs

OBJECTIVES

to assess the impact of universal adhesives, cured with single-peak and polywave LEDs, on the metabolic activity and cytokine release of human dental pulp stem cells (hDPSCs). In addition, analyze the degree of conversion (DC) of the adhesives cured with the different LEDs.

METHODS

Discs (5 mm diameter, 1 mm thick) were prepared using three universal adhesives: Single Bond Universal (SBU, 3 M ESPE), Optibond Universal (OBU, Kerr), and Zipbond Universal (ZBU, SDI). These discs were cured for 40 s using a single-peak (DeepCure, 3 M ESPE) or a polywave light-emmiting diode (LED) curing unit (Valo Grand, Ultradent). After 24 h, the specimens were placed in 24-well culture plates, each containing 1 mL of culture medium for 24 h. hDPSCs (1.8 ×104) were seeded in 96-well plates and allowed to grow for 24 h. Subsequently, the cells were exposed to the extracts (culture medium containing eluates from the adhesive discs) for an additional 24 h. Cells not exposed to the extracts were used as a control group. The mitochondrial metabolism was assessed using the MTT assay and the cytokine release evaluated through MAGPIX. The degree of conversion of the adhesives was analyzed using FTIR (n = 5). The results were analyzed by ANOVA two-way and Tukey's test.

RESULTS

OBU and ZBU eluates caused a statistically significant reduction in mitochondrial metabolism, regardless of the LED used, indicating their cytotoxicity. In contrast, SBU did not significantly affect the MTT results, resembling the control group. A higher release of cytokines IL-1, IL-6, IL-10, and TNF-α were found in association to ZBU. SBU, on the other hand, increased the release of IL-8. OBU did not influenced the cytokine release. SBU presented the higher DC, while OBU and ZBU had similar DC, lower than SBU.

SIGNIFICANCE

In conclusion, universal adhesives exhibit toxicity towards hDPSCs, but the extent of toxicity varies depending on the adhesive material. ZBU was associated with increased cytokine release, particularly pro-inflammatory mediators, from hDPSCs. The different LEDs did not influenced the cytotoxicity of the evaluated adhesives.

Effect of Optical Properties of Lithium Disilicate Glass Ceramics and Light-Curing Protocols on the Curing Performance of Resin Cement

This study aimed to investigate the effects of optical properties of lithium disilicate glass ceramics and the light-curing protocols (LCP) on the curing performance of light-cured resin cement. Lithium disilicate glass-ceramics with different optical properties were sectioned to produce ceramic specimens of 0.8 mm thickness. Irradiance through the ceramic specimens was measured by a radiometer. Light transmittance of ceramics was assessed using a UV/Vis spectrophotometer. The light-cured resin cement was injected into a Teflon mold and ceramics with different optical properties were placed on it, cured under different LCPs, and the degree of conversion (DC) and Vickers microhardness of the resin cement were separately measured by Micro-ATR/FTIR spectrometry and the microhardness tester. The shade (p < 0.001) and transparency (p < 0.001) of ceramics affect the irradiance of the light-curing unit. The transparency (p < 0.001) of the ceramic and light-curing protocols (p < 0.001) affect the DC and microhardness of resin cements. When the thickness of the ceramic is 0.8 mm, the light transmittance of the ceramic and the curing performance of the resin cement increase with the increase of the transparency of the ceramic. An appropriate increase in irradiance and exposure time can optimize the curing performance of resin cement. These factors should be taken into account by the clinician when designing the bonding solution for porcelain veneers.

Glass fiber posts relining: can composite opacity influence retention to root canal dentin?

This study aimed at evaluating the influence of glass-fiber post (GFP) relining with composites of different opacities on resin cement layer thickness (CLT), bond strength (BS) to root dentin, and resin cement degree of conversion (DC%). Standardized roots of 52 bovine incisors had their canals prepared and were distributed into 4 groups (n = 10 for CLT and BS; n = 3 for DC%) according to the post used: WP3 (Control)-Whitepost DC3; groups DE, EN and TR-Whitepost DC0.5 relined, respectively, with dentin, enamel, and translucent shade composites. After cementation, specimens were sectioned into six 1.0 mm-thick discs that were submitted to push-out BS test. CLT and failure pattern were evaluated using a stereomicroscope and DC% by micro-Raman spectroscopy. Data were analyzed by two-way ANOVA and Tukey test (α = 0.05). The control group showed greater CLT than all relined groups (p < 0.05), which did not differ from each other (p > 0.05). Groups relined with low opacity composites (TR; EN) showed the highest BS and DC% means (p < 0.05). BS was not different among root thirds (p > 0.05), while DC% decreased from cervical to apical third (p < 0.05). Adhesive failures between cement and dentin were predominant, except for group DE with frequent mixed failures. It could be concluded that composite opacity did not influence CLT, which was thinner when GFP were relined and that relining GFP with lower opacity composites led to higher BS and DC%.

Effects of Color Modifier on Degree of Monomer Conversion, Biaxial Flexural Strength, Surface Microhardness, and Water Sorption/Solubility of Resin Composites

Color modifiers can be mixed with resin composites to mimic the shade of severely discolored tooth. The aim of this study was to assess the effects of a color modifier on the physical and mechanical properties of a resin composite. The composite was mixed with a color modifier at 0 wt% (group 1), 1 wt% (group 2), 2.5 wt% (group 3), or 5 wt% (group 4). The degree of monomer conversion (DC) was examined after light curing for 20 or 40 s. Biaxial flexural strength (BFS)/modulus (BFM), surface microhardness (SH), and water sorption (W_sp)/solubility (W_sl) were also tested. The DC of group 1 was significantly higher than that of groups 3 and 4. The increase in curing time from 20 to 40 s increased the DC by ~10%. The BFS, BFM, W_sp, and W_sl of all the groups were comparable. A negative correlation was detected between the concentration of color modifier and the BFS and DC, while a positive correlation was observed with W_sp. In conclusion, the color modifier reduced the DC of composites, but the conversion was improved by extending the curing time. The increase in color modifier concentration also correlated with a reduction in strength and the increase in the water sorption of the composites.

Transmission of violet and blue light and current light units through glass-reinforced ceramics with different thicknesses

Purpose To evaluate the effect of glass-reinforced ceramics (leucite and lithium disilicate) with different thicknesses (1, 2, and 3 mm) on the wavelength and irradiance spectrum of blue and violet lights. In addition, the effect of the ceramics on four current light-curing units (LCUs) was evaluated: a halogen lamp, a single peak LED, and two multi-peak LEDs.Methods Ceramic discs of different thicknesses (1, 2, and 3 mm) were obtained from computer-aided design and computer-aided manufacturing (CAD-CAM) blocks. The irradiance, radiant exposure, and emission spectrum of the four LCUs were analyzed using a spectrometer-based instrument. To evaluate the violet and blue lights, a specific device that provides a narrow emission spectrum was used.Results The ceramics reduced the irradiance of all the tested LCUs. However, the wavelength of the transmitted light was only altered slightly. The effect of leucite and lithium disilicate varied according to the type of LCU and thickness of the ceramic disc evaluated .Conclusions From the results, it could be concluded that the thickness of the leucite and lithium disilicate ceramic significantly reduced the irradiance of the light emitted by the LCUs, with minimal changes on the wavelength spectrum of the lights. The effects of the ceramic on irradiance and transmitted wavelengths of the blue and violet lights was slightly different.

Physicochemical properties of dental resins formulated with amine-free photoinitiation systems

OBJECTIVE

To assess the mechanical properties of two different dimethacrylate resin blends containing the photosensitizer camphorquinone (CQ) alone or in combination with one or more synergists including an amine and/or an iodonium.

METHODS

Two co-monomer resin blends were formulated using Bis-GMA/TEGDMA and UDMA/TEGDMA, both at 1:1 mass ratio. Each resin blend was divided into four groups, comprising the following four photoinitiation systems: (1) CQ + 2-(dimethylamino)ethyl methacrylate (DMAEMA); (2) CQ + DMAEMA + bis(4-methyl phenyl)iodonium hexafluorophosphate (BPI); (3) CQ; and (4) CQ + BPI. Materials were evaluated for polymerisation kinetics, water sorption, solubility, flexural strength and modulus.

RESULTS

BisGMA/TEGDMA with CQ showed minimal and insignificant degree of conversion and was not tested for water sorption/solubility and mechanical properties. The ternary system (i.e., CQ + DMAEMA + BPI), promoted the highest degree of conversion for each monomer blend. The resins containing amine had higher mechanical properties than the amine free. However, the UDMA amine free resins exhibited greater flexural strength and modulus than the corresponding amine free BisGMA resins. BisGMA/TEGDMA containing CQ + DMAEMA or CQ + BPI had significantly higher water sorption and solubility than the other groups.

SIGNIFICANCE

Resins containing amine presented better properties than the amine-free systems. The addition of iodonium salt (BPI) improved the degree of conversion of the resins, even without an amine co-initiator. The amine-free initiator system (CQ + BPI) was more effective when used with UDMA versus BisGMA based-resins respectively.

Influence of Different Cordless Light-emitting-diode Units and Battery Levels on Chemical, Mechanical, and Physical Properties of Composite Resin

Clinical Relevance

Irradiance may decrease as the light-emitting diode (LED) is discharged. Therefore, the LED must be charged carefully to prevent the possibility of influencing the chemical, mechanical, and physical properties of composite resin.

SUMMARY

The aim of this study was to evaluate the influence of different light-emitting diode (LED) curing units and battery levels on the chemical, mechanical, and physical properties of composite resins. The irradiance for each cycle from full to completely discharged battery level was evaluated, for five different new cordless LED units: Optilight Color (Gnatus), Bluephase (Ivoclar), Valo (Ultradent), Radii Plus (SDI), and Radii Xpert (SDI). After the irradiance evaluation, composite resin specimens were prepared and light cured, while varying the battery level for each LED unit: high level (HL, 100%), medium level (ML, 50%), and low level (LL, 10%). The degree of conversion, diametral tensile strength, sorption, and solubility were also evaluated. Data were checked for homoscedasticity and submitted to two-way and three-way analysis of variance, depending on the test performed, followed by the Tukey test with a significance level of 95%. A negative correlation was found between irradiance and cycles of light curing, which was checked by the Pearson correlation test. Valo and Radii Xpert were not influenced by the battery level in any test performed. However, different battery levels for some LED units can influence the degree of conversion, diametral tensile strength, sorption, and solubility of composite resins.

Effects of radiant exposure and wavelength spectrum of light-curing units on chemical and physical properties of resin cements

Objectives

In this study, we evaluated the influence of different radiant exposures provided by single-peak and polywave light-curing units (LCUs) on the degree of conversion (DC) and the mechanical properties of resin cements.

Materials and Methods

Six experimental groups were established for each cement (RelyX ARC, 3M ESPE; LuxaCore Dual, Ivoclar Vivadent; Variolink, DMG), according to the different radiant exposures (5, 10, and 20 J/cm²) and two LCUs (single-peak and polywave). The specimens were made (7 mm in length × 2 mm in width × 1 mm in height) using silicone molds. After 24 hours of preparation, DC measurement was performed using Fourier transform infrared spectrometry. The same specimens were used for the evaluation of mechanical properties (flexural strength, FS; elastic modulus, E) by a three-point bending test. Data were assessed for normality, after which two-way analysis of variance (ANOVA) and post hoc Tukey's test were performed.

Results

No properties of the Variolink cement were influenced by any of the considered experimental conditions. In the case of the RelyX ARC cement, DC was higher when polywave LCU was used; FS and E were not influenced by the conditions evaluated. The LuxaCore cement showed greater sensitivity to the different protocols.

Conclusions

On the basis of these results, both the spectrum of light emitted and the radiant exposure used could affect the properties of resin cements. However, the influence was material-dependent.

Effect of diphenyliodonium hexafluorphosphate on resin cements containing different concentrations of ethyl 4-(dimethylamino)benzoate and 2-(dimethylamino)ethyl methacrylate as co-initiators

OBJECTIVE

The present study evaluated the influence of diphenyliodonium hexafluorphosphate (DPI) combined with two different amines [ethyl 4-(dimethylamino)benzoate (EDAB) and 2-(dimethylamino)ethyl methacrylate (DMAEMA)] on the properties of model resin cements.

METHODS

A comonomer base containing a 1:1 mass ratio of 2.2-bis[4-(2-hydroxy-3-methacryloxypropoxy)phenyl]propane (bis-GMA) and triethyleneglycol dimethacrylate (TEGDMA) was obtained, after which 1mol% of camphorquinone and 0.1mol% of hydroxyl butyl toluene were added to the comonomer blend. Concentrations of co-initiators varied at 0, 0.5 or 1mol% for DPI and in 1 or 2mol% for amines (DMAEMA or EDAB). Silanated Ba-Al-Si glass (60wt%) was added as filler. The combination of each amine and DPI concentration resulted in 12 formulations, which had the following properties analyzed: degree of conversion (DC), water sorption (Wsp) and solubility (Wsl), flexural strength (FS) and flexural modulus (Ef). Data for DC, FS and Ef were analyzed by two-way ANOVA and Tukey's test (α=0.05) and Wsp and Wsl by Kruskal-Wallis and Dunn tests (α=0.05).

RESULTS

EDAB promoted a higher DC than did DMAEMA; however, DPI increased DC for all materials with DMAEMA. The physical properties of resin formulations containing EDAB were significantly better than those of groups with DMAEMA; however, DPI had a positive influence on the chemical and physical properties of the model resin cement containing DMAEMA, especially with higher concentrations of amine.

SIGNIFICANCE

EDAB proved to be more reactive than DMAEMA, being less influenced by DPI. Resins containing a 1:2 CQ/amine ratio had better properties than those with 1:1.

Effect of preheating and shade on surface microhardness of silorane-based composites

AIM

The aim of the present study was to evaluate the effect of preheating and shade on the surface microhardness of silorane-based composites.

METHODS

Three shades of two different types of composites were evaluated: a silorane-based composite and a methacrylate-based composite. The composites were tested at 23°C, and after preheating at 55°C. Five specimens were prepared for each experimental group. The top surface of the specimens was irradiated for 20 s using an LED unit. Vickers microhardness test was used to evaluate both top and bottom surfaces of the specimens, followed by 24-h storage in the dark. Statistical analysis was performed using one-way anova and Tukey's post-hoc test at a level of significance of α = 0.05.

RESULTS

There was a significant rise in microhardness as the temperature increased from 23 to 55°C for both the top and bottom surfaces of the tested composites (P < 0.05). The C2 shade of both composites exhibited the lowest microhardness (P < 0.05), while the A2 and A3 shades did not show significant differences compared to each other (P > 0.05) Filtek Silorane presented significantly lower microhardness than Filtek Z250 (P < 0.05), regardless of the temperature, shade, or depth of measurement.

CONCLUSIONS

Preheating, shade, and composition of the tested composite resins affected their surface microhardness.

Effect of ceramic shade on the degree of conversion of a dual-cure resin cement analyzed by FTIR

OBJECTIVES

The aim of this research was to evaluate the degree of monomer conversion of different resin cement shades when photocured under different feldspathic ceramic shades. The photocuring time was also evaluated as well as the translucency of each ceramic shade.

METHODS

Three VITA VM7 ceramic shades (Base Dentin 0M1, Base Dentin 2M2 and Base Dentin 5M3) were used to determine the translucency percentage. A spectrophotometer MiniScan was used to measure the opacity percentage of each specimen (2-mm-thick) and then the translucency was calculated. To measure the degree of conversion (DC), the resin cement (Variolink II; A3 Yellow and transparent) specimens (thickness: 100 μm) were photocured under a ceramic block (2-mm-thick) for 20 or 40s. Specimens photocured without the ceramic block were used as control. Sixteen groups (n=3) were evaluated. Micro-ATR/FTIR spectrometry was used to evaluate the extent of polymerization of all specimens after 24h. The %DC was calculated of experimentally polymerized versus maximally polymerized composite.

RESULTS

The translucency percentages of 0M1, 2M2 and 5M3 ceramics were 12.41 (1.02)%, 5.75 (1.91)% and 1.07 (0.03)%, respectively. The %DC of both resin cement shades cured under ceramic 5M3 was significantly lower than the other groups (p<0.05). The %DC of 0M1 groups exhibited no significant difference from 2M2 groups (p>0.05), with the exception of the transparent cement photocured for 40s.

CONCLUSION

Photocuring under 2mm ceramic showed that the increase in chroma saturation significantly decreased Variolink II resin cement %DC (100-μm-thick).

Effect of light-activation with different light-curing units and time intervals on resin cement bond strength to intraradicular dentin

The aim of this study was to assess the bond strength of a resin cement to intraradicular dentin varying the light-curing unit and the moment at which the light was applied. Post spaces of endodontically treated canines were prepared. The roots were distributed into 6 groups (n=10) according to the light-curing unit and the moment of light exposure: I) Quartz tungsten halogen-600 mW/cm² (QTH) + immediate light activation (t0); II) QTH + light activation after 10 min (t10); III) Light-emitting diodes (LED)-800 mW/cm² (LED-800)+ t0; IV) LED-800 + t10; V) LED-1,500 mW/cm² (LED-1500)+ t0; VI) LED-1500 + t10. After post cementation, slices from coronal, middle and apical post/root regions were submitted to the push-out test and failure evaluation. It was verified that LED-800 (4.40 ± 3.00 MPa) and LED-1500 (4.67 ± 3.04 MPa) provided bond strength statistically superior to QTH (3.13 ± 1.76 MPa) (p<0.05), and did not differ from each other (p>0.05). There was no significant difference between t0 and t10 (p>0.05). Coronal post/root region (4.75 ± 3.10 MPa) presented significantly higher bond strength than the apical (3.32 ± 2.30 MPa) (p<0.05) and middle regions (4.14 ± 2.99 MPa) showed intermediate values. Adhesive failures were predominant when using QTH. Adhesive and mixed failures occurred more frequently in the apical region. Higher adhesion of the resin cement to intraradicular dentin was observed in the coronal region with LED light-activation, regardless of the moment of light exposure.