Effect of Three Wavelengths of Diode Laser on the Efficacy of Bleaching of Stained Teeth

Evaluation of tooth color change after a bleaching process with different lasers

The aim of this in vitro study was to evaluate the efficiency of diode laser-activated bleaching systems for color change of teeth. 75 extracted teeth were studied in five different bleaching protocols. Group 1: diode laser 445 nm, 320 µm fiber, 0.5W, continuous wave mode, dose 53 J/cm2. Group 2: diode laser 970 nm, 320 µm fiber, 1W, continuous wave mode, dose 106.10 J/cm2. Group 3: diode laser 940 nm, bleaching handpiece, 7W, continuous wave mode, dose 105 J/cm2. Group 4: diode laser 940 nm, 300 µm fiber, 2W, continuous wave mode, dose 47.16 J/cm2. Group 5: bleaching process without laser activation. In groups 1, 2 and 5, teeth were bleached with Perfect Bleach Office + and in groups 3 and 4, LaserWhite20 bleaching gel was used. Tooth color was determined immediately after the bleaching process using a spectrophotometer. Color change data on the CIE L * a * b* system was analyzed statistically by the one-way ANOVA and Tukey's HSD test. All bleaching procedures resulted in a change of color. All laser groups (∆E * ab > 3) have statistically larger ∆E * ab values than the control group (∆E * ab = 0.73) (p < 0.05). The diode laser 445 nm has the largest ∆E * ab value (∆E * ab = 4.65) and results in a significantly higher color difference than all other groups. In terms of color score difference in VITA Shades, all laser-activated groups lead to a lightening effect while the control group leads to only a slight lightening effect. The diode laser 445 nm produced the greatest color difference. Laser-activated bleaching is more effective than conventional bleaching without light activation. The diode laser 445 nm performs best in this in vitro study.

Effect of Laser and Conventional Office Bleaching and Polishing on the Color Change of Stained Nanohybrid and Microhybrid Composite Resin

Aim

The present study investigated the effects of laser and conventional in-office bleaching, and polishing on the color of stained composite resin.

Materials and Methods

A microhybrid composite (Clearfil AP-X) and a nanohybrid composite (Grandio) were selected. Twenty-four discs (2 × 10 mm) for each composite were prepared. The samples were immersed in coffee solution (25 g of coffee in 250 mL water) for seven days. Then the samples were divided into three groups (n = 8) and the stains were removed using bleaching (with Opalescence Xtra Boost), diode laser irradiation with Heydent material and a Sof-Lex polishing kit. The L ∗a ∗b ∗ color parameters were determined using a spectrophotometer before and after immersion and after stain removal procedures, and the overall color changes (ΔE) were calculated. The data were analyzed with two-way analysis of variance.

Results

In the Clearfil composite resin group, the mean ΔE compared to the baseline using in-office bleaching, laser irradiation, and Sof-Lex polishing kit were 3.31, 3.35, and 4.93, respectively. These values with the Grandio composite resin were 3.31, 6.35, and 4.57, respectively. The highest capacity to remove stains was related to the conventional in-office bleaching method. Grandio composite resin underwent more color changes than Clearfil composite resin significantly (P-value < 0.05).

Conclusion

Both composite resins exhibited color changes after immersion in the discoloring solution. However, after staining-removing procedures, the ΔE values decreased. Decreases in the ΔE values were not sufficient to restore the color to that before immersion in the discoloring solution with any stain-removing methods.

The impact of the diode laser 940 nm photoactivated bleaching on color change of different composite resin restorations

The study's main objective was to evaluate as well as compare the impact of diode laser 940 nm and conventional in-office bleaching technique on the color change of different composite resin restorations. A total of ninety composite resin discs (CRDs) were made from Filtek™ Bulk Fill, nanohybrid composite resin Filtek™ Z550 XT Universal Restorative, and flowable composite resin restoration Filtek™ Z350xt Flowable Composite. Group A: (30) CRD for Filtek™ Bulk Fill, group B: (30) CRD for Filtek™ Z550 XT Universal Restorative, and group C: (30) CRD for Filtek™ Z350xt Flowable Composite. A1, B1, and C1: (10 CRD in each group): Control group without bleaching. A2, B2, and C2: 10 CRD in each group bleached with Laser White20 without laser activation. A3, B3, and C3: 10 CRD in each group bleached with Laser White20 and activated by diode laser 940 nm. The color was evaluated using a dental spectrophotometer. One-way ANOVA was utilized for the comparison of the color stability of the CRD. P < 0.05 is regarded as statically significant. Both conventional and diode laser in-office vital tooth bleaching protocols affected the color stability of composite resin restorations. The result demonstrated that bleaching without laser activation produced color change (mean [8.30], standard deviation [SD] (1.95) P [< 0.001]), whereas the bleaching and activation by diode laser produced color change (mean [8.11], SD [1.99], P [< 0.001]). Both types of bleaching protocol affected composite resin restorations' color stability. In all tested materials, color changes after the bleaching protocol were clinically perceptible. The restorations following the bleaching procedure are required to be replaced by clinicians.

Effect of Er:YAG laser irrigation with different etching modes on the push-out bond strength of fiber posts to the root dentine

The objective of this study was to evaluate the effect of Er:YAG laser irrigation on the push-out bond strength of fiber posts to the root dentine. Sixty extracted human mandibular first premolars were collected and decoronated. The residual roots received endodontic treatment. The treated roots were randomly divided into three groups according to different irrigation protocols: group LAI (Er:YAG laser–activated irrigation), group PUI (passive ultrasonic irrigation, positive control), and group CSI (conventional syringe irrigation, negative control) (n = 20). Each group was divided into two subgroups, either total-etching modes or self-etching modes (n = 10). After fiber post restoration, all roots were sectioned into seven 1.0-mm-thick slices. The slices received a push-out test by a universal test machine. The resin tag on the segments’ bonding interfaces was observed by scanning electron microscope. There were significant differences in the effects of the irrigation method, bonding modes, and root regions on the push-out bond strength among the groups (p < 0.05). The specimens with Er:YAG laser–activated irrigation and self-etching mode showed significantly the highest bonding strength (p < 0.001). The lengths and densities of resin tags in group PUI or group LAI with self-etching modes were longer than those in group CSI with total-etching modes. The laser-activated irrigation with self-etching modes improved the bond strength of fiber post to root dentine compared to the passive ultrasonic irrigation or conventional syringe irrigation with total or self-etching modes.