Field Analysis of Polychlorinated Biphenyls (PCBs) in Soil Using Solid-Phase Microextraction (SPME) and a Portable Gas Chromatography-Mass Spectrometry System

An expedited field analysis method was developed for the determination of polychlorinated biphenyls (PCBs) in soil matrices using a portable gas chromatography-mass spectrometry (GC-MS) instrument. Soil samples of approximately 0.5 g were measured with a portable scale and PCBs were extracted by headspace solid-phase microextraction (SPME) with a 100 µm polydimethylsiloxane (PDMS) fiber. Two milliliters of 0.2 M potassium permanganate and 0.5 mL of 6 M sulfuric acid solution were added to the soil matrices to facilitate the extraction of PCBs. The extraction was performed for 30 min at 100 ℃ in a portable heating block that was powered by a portable generator. The portable GC-MS instrument took less than 6 min per analysis and ran off an internal battery and helium cylinder. Six commercial PCB mixtures, Aroclor 1016, 1221, 1232, 1242, 1248, 1254, and 1260, could be classified based on the GC chromatograms and mass spectra. The detection limit of this method for Aroclor 1260 in soil matrices is approximately 10 ppm, which is sufficient for guiding remediation efforts in contaminated sites. This method was applicable to the on-site analysis of PCBs with a total analysis time of 37 min per sample. However, the total analysis time could be improved to less than 7 min per sample by conducting the rate-limiting extraction step for different samples in parallel.

Development and verification of a model for estimating the screening utility in the detection of PCBs in transformer oil

A simple new model for estimating the screening performance (false positive and false negative rates) of a given test for a specific sample population is presented. The model is shown to give good results on a test population, and is used to estimate the performance on a sampled population. Using the model developed in conjunction with regulatory requirements and the relative costs of the confirmatory and screening tests allows evaluation of the screening test's utility in terms of cost savings. Testers can use the methods developed to estimate the utility of a screening program using available screening tests with their own sample populations.

Pretreatment method for immunoassay of polychlorinated biphenyls in transformer oil using multilayer capillary column and microfluidic liquid-liquid partitioning

Polychlorinated biphenyls (PCBs) are persistent organic pollutants that are present in the insulating oil inside a large number of transformers. To aid in eliminating PCB-contaminated transformers, PCBs in oil need to be measured using a rapid and cost-effective analytical method. We previously reported a pretreatment method for the immunoassay of PCBs in oil using a large-scale multilayer column and a microchip with multiple microrecesses, which permitted concentrated solvent extraction. In this paper, we report on a more rapid and facile pretreatment method, without an evaporation process, by improving the column and the microchip. In a miniaturized column, the decomposition and separation of oil were completed in 2 min. PCBs can be eluted from the capillary column at concentrations seven-times higher than those from the previous column. The total volume of the microrecesses was increased by improving the microrecess structure, the enabling extraction of four-times the amount of PCBs achieved with the previous system. By interfacing the capillary column with the improved microchip, PCBs in the eluate from the column were extracted into dimethyl sulfoxide in microrecesses with high enrichment and without the need for evaporation. Pretreatment was completed within 20 min. The pretreated oil was analyzed using a flow-based kinetic exclusion immunoassay. The limit of detection of PCBs in oil was 0.15 mg kg(-1), which satisfies the criterion set in Japan of 0.5 mg kg(-1).

Optimization of a commercial biosensor for polychlorinated biphenyls and evaluation of its utility for screening

We previously described our systematic progress that eventually resulted in a commercially available immunoassay based biosensor (PCB biosensor) for detecting PCBs in oil. However, IC50 of the commercialized PCB biosensor was approximately 2 ppb for PCBs, and did not achieve the theoretical detection limit (TDL) which would represent an IC50 of approximately 0.5 ppb. In this study, we characterize the effects of the antibody concentration, flow volume and flow rate on the PCB biosensor's response. Using the optimum operating conditions, the PCB biosensor achieved the TDL and its performance as a screening test was improved. Working at the stringent maximum residue limit specified by Japanese law (0.5 ppm total PCBs), the optimized biosensor exhibited excellent performance (0% false negatives and 7% false positives) in the screening of 110 samples of used Japanese transformer oil. The general approach for optimization described here is expected to benefit immunoassay researchers attempting to achieve optimum performance.

Analysis of polychlorinated biphenyls in transformer oil by using liquid-liquid partitioning in a microfluidic device

Polychlorinated biphenyls (PCBs) that are present in transformer oil are a common global problem because of their toxicity and environmental persistence. The development of a rapid, low-cost method for measurement of PCBs in oil has been a matter of priority because of the large number of PCB-contaminated transformers still in service. Although one of the rapid, low-cost methods involves an immunoassay, which uses multilayer column separation, hexane evaporation, dimethyl sulfoxide (DMSO) partitioning, antigen-antibody reaction, and a measurement system, there is a demand for more cost-effective and simpler procedures. In this paper, we report a DMSO partitioning method that utilizes a microfluidic device with microrecesses along the microchannel. In this method, PCBs are extracted and enriched into the DMSO confined in the microrecesses under the oil flow condition. The enrichment factor was estimated to be 2.69, which agreed well with the anticipated value. The half-maximal inhibitory concentration of PCBs in oil was found to be 0.38 mg/kg, which satisfies the much stricter criterion of 0.5 mg/kg in Japan. The developed method can realize the pretreatment of oil without the use of centrifugation for phase separation. Furthermore, the amount of expensive reagents required can be reduced considerably. Therefore, our method can serve as a powerful tool for achieving a simpler, low-cost procedure and an on-site analysis system.