1
|
Ervik TK, Leite M, Weinbruch S, Nordby KC, Ellingsen DG, Ulvestad B, Dahl K, Berlinger B, Skaugset NP. Characterization of particle exposure during tunnel excavation by tunnel boring machines. Ann Work Expo Health 2024:wxae041. [PMID: 38816184 DOI: 10.1093/annweh/wxae041] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/29/2023] [Accepted: 05/02/2024] [Indexed: 06/01/2024] Open
Abstract
Tunnel boring machines (TBMs) are used to excavate tunnels in a manner where the rock is constantly penetrated with rotating cutter heads. Fine particles of the rock minerals are thereby generated. Workers on and in the vicinity of the TBM are exposed to particulate matter (PM) consisting of bedrock minerals including α-quartz. Exposure to respirable α-quartz remains a concern because of the respiratory diseases associated with this exposure. The particle size distribution of PM and α-quartz is of special importance because of its influence on adverse health effects, monitoring and control strategies as well as accurate quantification of α-quartz concentrations. The major aim of our study was therefore to investigate the particle size distribution of airborne PM and α-quartz generated during tunnel excavation using TBMs in an area dominated by gneiss, a metamorphic type of rock. Sioutas cascade impactors were used to collect personal samples on 3 separate days. The impactor fractionates the dust in 5 size fractions, from 10 µm down to below 0.25 µm. The filters were weighted, and the α-quartz concentrations were quantified using X-ray diffraction (XRD) analysis and the NIOSH 7500 method on the 5 size fractions. Other minerals were determined using Rietveld refinement XRD analysis. The size and elemental composition of individual particles were investigated by scanning electron microscopy. The majority of PM mass was collected on the first 3 stages (aerodynamic diameter = 10 to 0.5 µm) of the Sioutas cascade impactor. No observable differences were found for the size distribution of the collected PM and α-quartz for the 3 sampling days nor the various work tasks. However, the α-quartz proportion varied for the 3 sampling days demonstrating a dependence on geology. The collected α-quartz consisted of more particles with sizes below 1 µm than the calibration material, which most likely affected the accuracy of the measured respirable α-quartz concentrations. This potential systematic error is important to keep in mind when analyzing α-quartz from occupational samples. Knowledge of the particle size distribution is also important for control measures, which should target particle sizes that efficiently capture the respirable α-quartz concentration.
Collapse
Affiliation(s)
- Torunn K Ervik
- National Institute of Occupational Health, P.O. Box 5330, Majorstuen, 0304 Oslo, Norway
| | - Mimmi Leite
- National Institute of Occupational Health, P.O. Box 5330, Majorstuen, 0304 Oslo, Norway
| | - Stephan Weinbruch
- National Institute of Occupational Health, P.O. Box 5330, Majorstuen, 0304 Oslo, Norway
- Technical University of Darmstadt, Institute of Applied Geosciences, Schnittspahnstrasse 9, D-64287, Darmstadt, Germany
| | - Karl-Christian Nordby
- National Institute of Occupational Health, P.O. Box 5330, Majorstuen, 0304 Oslo, Norway
| | - Dag G Ellingsen
- National Institute of Occupational Health, P.O. Box 5330, Majorstuen, 0304 Oslo, Norway
| | - Bente Ulvestad
- National Institute of Occupational Health, P.O. Box 5330, Majorstuen, 0304 Oslo, Norway
| | - Kari Dahl
- National Institute of Occupational Health, P.O. Box 5330, Majorstuen, 0304 Oslo, Norway
| | - Balazs Berlinger
- National Institute of Occupational Health, P.O. Box 5330, Majorstuen, 0304 Oslo, Norway
| | - Nils Petter Skaugset
- National Institute of Occupational Health, P.O. Box 5330, Majorstuen, 0304 Oslo, Norway
| |
Collapse
|