1
|
Witkowska J, Borowski T, Sowińska A, Choińska E, Moszczyńska D, Morgiel J, Sobiecki J, Wierzchoń T. Influence of Low Temperature Plasma Oxidizing on the Bioactivity of NiTi Shape Memory Alloy for Medical Applications. MATERIALS (BASEL, SWITZERLAND) 2023; 16:6086. [PMID: 37763363 PMCID: PMC10533197 DOI: 10.3390/ma16186086] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 08/02/2023] [Revised: 08/24/2023] [Accepted: 08/31/2023] [Indexed: 09/29/2023]
Abstract
The present study elucidates the impact of glow discharge oxidation within a low-temperature plasma environment on the bioactivity characteristics of an NiTi shape memory alloy. The properties of the produced surface layers, such as structure (TEM observations), surface morphology (SEM observations), chemical and phase composition (EDS and XRD measurements), wettability (optical gonimeter), and the biological response of osteoblasts and platelets to the oxidized surface compared with the NiTi alloy without a surface layer are presented. The presented surface modification of the NiTi shape memory alloy, achieved through oxidizing in a low-temperature plasma environment, led to the creation of a continuous surface layer composed of nanocrystalline titanium oxide TiO2 (rutile). The findings obtained from this study provide evidence that the oxidized layer augments the bioactivity of the shape memory alloy. This augmentation was substantiated through the spontaneous biomimetic deposition of apatite from a simulated body fluid (SBF) solution. Furthermore, the modified surface exhibited improved osteoblast proliferation, and enhanced platelet adhesion and activation. This proposed surface modification strategy holds promise as a prospective solution to enhance the biocompatibility and bioactivity of NiTi shape memory alloy intended for prolonged use in bone implant applications.
Collapse
Affiliation(s)
- Justyna Witkowska
- Faculty of Materials Science and Engineering, Warsaw University of Technology, 02-507 Warsaw, Poland; (T.B.); (E.C.); (D.M.); (J.S.); (T.W.)
| | - Tomasz Borowski
- Faculty of Materials Science and Engineering, Warsaw University of Technology, 02-507 Warsaw, Poland; (T.B.); (E.C.); (D.M.); (J.S.); (T.W.)
| | - Agnieszka Sowińska
- Pathology Department, Children’s Memorial Health Institute, 04-730 Warsaw, Poland;
| | - Emilia Choińska
- Faculty of Materials Science and Engineering, Warsaw University of Technology, 02-507 Warsaw, Poland; (T.B.); (E.C.); (D.M.); (J.S.); (T.W.)
| | - Dorota Moszczyńska
- Faculty of Materials Science and Engineering, Warsaw University of Technology, 02-507 Warsaw, Poland; (T.B.); (E.C.); (D.M.); (J.S.); (T.W.)
| | - Jerzy Morgiel
- Institute of Metallurgy and Materials Science, Polish Academy of Sciences, 30-059 Krakow, Poland;
| | - Jerzy Sobiecki
- Faculty of Materials Science and Engineering, Warsaw University of Technology, 02-507 Warsaw, Poland; (T.B.); (E.C.); (D.M.); (J.S.); (T.W.)
| | - Tadeusz Wierzchoń
- Faculty of Materials Science and Engineering, Warsaw University of Technology, 02-507 Warsaw, Poland; (T.B.); (E.C.); (D.M.); (J.S.); (T.W.)
| |
Collapse
|
2
|
Cherian AM, Nair SV, Maniyal V, Menon D. Surface engineering at the nanoscale: A way forward to improve coronary stent efficacy. APL Bioeng 2021; 5:021508. [PMID: 34104846 PMCID: PMC8172248 DOI: 10.1063/5.0037298] [Citation(s) in RCA: 19] [Impact Index Per Article: 6.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/12/2020] [Accepted: 04/26/2021] [Indexed: 12/12/2022] Open
Abstract
Coronary in-stent restenosis and late stent thrombosis are the two major inadequacies of vascular stents that limit its long-term efficacy. Although restenosis has been successfully inhibited through the use of the current clinical drug-eluting stent which releases antiproliferative drugs, problems of late-stent thrombosis remain a concern due to polymer hypersensitivity and delayed re-endothelialization. Thus, the field of coronary stenting demands devices having enhanced compatibility and effectiveness to endothelial cells. Nanotechnology allows for efficient modulation of surface roughness, chemistry, feature size, and drug/biologics loading, to attain the desired biological response. Hence, surface topographical modification at the nanoscale is a plausible strategy to improve stent performance by utilizing novel design schemes that incorporate nanofeatures via the use of nanostructures, particles, or fibers, with or without the use of drugs/biologics. The main intent of this review is to deliberate on the impact of nanotechnology approaches for stent design and development and the recent advancements in this field on vascular stent performance.
Collapse
Affiliation(s)
- Aleena Mary Cherian
- Amrita Centre for Nanosciences and Molecular Medicine, Amrita
Vishwa Vidyapeetham, Ponekkara P.O. Cochin 682041, Kerala,
India
| | - Shantikumar V. Nair
- Amrita Centre for Nanosciences and Molecular Medicine, Amrita
Vishwa Vidyapeetham, Ponekkara P.O. Cochin 682041, Kerala,
India
| | - Vijayakumar Maniyal
- Department of Cardiology, Amrita Institute of Medical Science
and Research Centre, Amrita Vishwa Vidyapeetham, Ponekkara P.O. Cochin
682041, Kerala, India
| | - Deepthy Menon
- Amrita Centre for Nanosciences and Molecular Medicine, Amrita
Vishwa Vidyapeetham, Ponekkara P.O. Cochin 682041, Kerala,
India
| |
Collapse
|
3
|
Melchor-Martínez EM, Torres Castillo NE, Macias-Garbett R, Lucero-Saucedo SL, Parra-Saldívar R, Sosa-Hernández JE. Modern World Applications for Nano-Bio Materials: Tissue Engineering and COVID-19. Front Bioeng Biotechnol 2021; 9:597958. [PMID: 34055754 PMCID: PMC8160436 DOI: 10.3389/fbioe.2021.597958] [Citation(s) in RCA: 13] [Impact Index Per Article: 4.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/23/2020] [Accepted: 04/21/2021] [Indexed: 12/12/2022] Open
Abstract
Over the past years, biomaterials-based nano cues with multi-functional characteristics have been engineered with high interest. The ease in fine tunability with maintained compliance makes an array of nano-bio materials supreme candidates for the biomedical sector of the modern world. Moreover, the multi-functional dimensions of nano-bio elements also help to maintain or even improve the patients' life quality most securely by lowering or diminishing the adverse effects of in practice therapeutic modalities. Therefore, engineering highly efficient, reliable, compatible, and recyclable biomaterials-based novel corrective cues with multipurpose applications is essential and a core demand to tackle many human health-related challenges, e.g., the current COVID-19 pandemic. Moreover, robust engineering design and properly exploited nano-bio materials deliver wide-ranging openings for experimentation in the field of interdisciplinary and multidisciplinary scientific research. In this context, herein, it is reviewed the applications and potential on tissue engineering and therapeutics of COVID-19 of several biomaterials. Following a brief introduction is a discussion of the drug delivery routes and mechanisms of biomaterials-based nano cues with suitable examples. The second half of the review focuses on the mainstream applications changing the dynamics of 21st century materials. In the end, current challenges and recommendations are given for a healthy and foreseeable future.
Collapse
|
4
|
Witkowska J, Sowińska A, Czarnowska E, Płociński T, Rajchel B, Tarnowski M, Wierzchoń T. Structure and properties of composite surface layers produced on NiTi shape memory alloy by a hybrid method. JOURNAL OF MATERIALS SCIENCE. MATERIALS IN MEDICINE 2018; 29:110. [PMID: 30019236 PMCID: PMC6061091 DOI: 10.1007/s10856-018-6118-5] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.2] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 04/13/2018] [Accepted: 07/04/2018] [Indexed: 06/08/2023]
Abstract
A hybrid process that combines oxidation under glow-discharge conditions with ion beam-assisted deposition (IBAD) has been applied to mechanically polished NiTi shape memory alloy in order to produce composite surface layers consisting of a TiO2 layer and an external carbon coating with an addition of silver. The produced surface layers a-C(Ag) + TiO2 type have shown increased surface roughness, improved corrosion resistance, altered wettability, and surface free energy, as well as reduced platelet adhesion, aggregation, and activation in comparison to NiTi alloy in initial state. Such characteristics can be of great benefit for cardiac applications.
Collapse
Affiliation(s)
- Justyna Witkowska
- Faculty of Materials Science and Engineering, Warsaw University of Technology, Wołoska 141, 02-507, Warsaw, Poland.
| | - Agnieszka Sowińska
- Pathology Department, Children's Memorial Health Institute, Dzieci Polskich 20, 04-730, Warsaw, Poland
| | - Elżbieta Czarnowska
- Pathology Department, Children's Memorial Health Institute, Dzieci Polskich 20, 04-730, Warsaw, Poland
| | - Tomasz Płociński
- Faculty of Materials Science and Engineering, Warsaw University of Technology, Wołoska 141, 02-507, Warsaw, Poland
| | - Bogusław Rajchel
- Institute of Nuclear Physics Polish Academy of Sciences, Radzikowskiego 152, 31-342, Cracow, Poland
| | - Michał Tarnowski
- Faculty of Materials Science and Engineering, Warsaw University of Technology, Wołoska 141, 02-507, Warsaw, Poland
| | - Tadeusz Wierzchoń
- Faculty of Materials Science and Engineering, Warsaw University of Technology, Wołoska 141, 02-507, Warsaw, Poland
| |
Collapse
|
5
|
Bakola V, Karagkiozaki V, Tsiapla AR, Pappa F, Moutsios I, Pavlidou E, Logothetidis S. Dipyridamole-loaded biodegradable PLA nanoplatforms as coatings for cardiovascular stents. NANOTECHNOLOGY 2018; 29:275101. [PMID: 29629708 DOI: 10.1088/1361-6528/aabc69] [Citation(s) in RCA: 16] [Impact Index Per Article: 2.7] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/08/2023]
Abstract
Cardiovascular stents are commonly used for the treatment of cardiovascular diseases that in developed societies are the most frequent causes of mortality and morbidity. In recent years, thorough research and development of drug-eluting stents has been done, with emphasis on coronary stenting to avoid the most common complication, in-stent thrombosis. Dipyridamole (DPM) is a medication that inhibits blood clot formation. Drug delivery nanoplatforms consisting of biodegradable polymers can be fabricated via electrospinning deposition, known for its cost-effective and versatile advantages, that produces fibrous scaffolds that are able to sustain and control drug release. A novel drug delivery nanosystem of polylactic acid fibrous scaffold loaded with the anti-platelet drug DPM was fabricated by electrospinning as coating for cardiovascular stents. The surface morphology and topography that were evaluated via atomic force microscopy, scanning electron microscopy and optical microscopy, were found to be good and suitable for tissue engineering. Contact angle measurements established the hydrophobic behavior of these fibrous nanoplatforms. Drug-release kinetics and degradation studies were conducted and revealed a sustained and controllable release of DPM, through this fibrous matrix over time. Finally, cytotoxicity studies took place to evaluate the cytocompatibility of the scaffold that confirmed its compatible behavior. The successful performance of this nanoplatform can lead to it being a valuable tool for atherosclerosis treatment.
Collapse
Affiliation(s)
- V Bakola
- Nanotechnology Lab LTFN (Lab for Thin Films-Nanobiomaterials-Nanosystems-Nanometrology) Aristotle University of Thessaloniki, 54124, Thessaloniki, Greece. BL Nanobiomed P.C. Thessaloniki, Greece
| | | | | | | | | | | | | |
Collapse
|
6
|
Abstract
Implanting a metal stent plays a key role in treating cardiovascular diseases. However, the high corrosion rate of metal-based devices severely limits their practical applications. Therefore, how to control the corrosion rate is vital to take full advantages of metal-based materials in the treatment of cardiovascular diseases. This review details various methods to design and construct polymer-coated stents. The techniques are described and discussed including plasma deposition, electrospinning, dip coating, layer-by-layer self-assembly, and direct-write inkjet. Key point is provided to highlight current methods and recent advances in hindering corrosion rate and improving biocompatibility of stents, which greatly drives the rising of some promising techniques involved in the ongoing challenges and potential new trends of polymer-coated stents.
Collapse
|
7
|
Burton HE, Freij JM, Espino DM. Dynamic Viscoelasticity and Surface Properties of Porcine Left Anterior Descending Coronary Arteries. Cardiovasc Eng Technol 2017; 8:41-56. [PMID: 27957718 PMCID: PMC5320017 DOI: 10.1007/s13239-016-0288-4] [Citation(s) in RCA: 37] [Impact Index Per Article: 5.3] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 09/03/2016] [Accepted: 11/30/2016] [Indexed: 12/12/2022]
Abstract
The aim of this study was, for the first time, to measure and compare quantitatively the viscoelastic properties and surface roughness of coronary arteries. Porcine left anterior descending coronary arteries were dissected ex vivo. Viscoelastic properties were measured longitudinally using dynamic mechanical analysis, for a range of frequencies from 0.5 to 10 Hz. Surface roughness was calculated following three-dimensional reconstructed of surface images obtained using an optical microscope. Storage modulus ranged from 14.47 to 25.82 MPa, and was found to be frequency-dependent, decreasing as the frequency increased. Storage was greater than the loss modulus, with the latter found to be frequency-independent with a mean value of 2.10 ± 0.33 MPa. The circumferential surface roughness was significantly greater (p < 0.05) than the longitudinal surface roughness, ranging from 0.73 to 2.83 and 0.35 to 0.92 µm, respectively. However, if surface roughness values were corrected for shrinkage during processing, circumferential and longitudinal surface roughness were not significantly different (1.04 ± 0.47, 0.89 ± 0.27 µm, respectively; p > 0.05). No correlation was found between the viscoelastic properties and surface roughness. It is feasible to quantitatively measure the viscoelastic properties of coronary arteries and the roughness of their endothelial surface.
Collapse
Affiliation(s)
- Hanna E. Burton
- Department of Mechanical Engineering, University of Birmingham, Birmingham, B15 2TT UK
| | - Jenny M. Freij
- Department of Mechanical Engineering, University of Birmingham, Birmingham, B15 2TT UK
| | - Daniel M. Espino
- Department of Mechanical Engineering, University of Birmingham, Birmingham, B15 2TT UK
| |
Collapse
|
8
|
Li Y, Xiao Y, Liu C. The Horizon of Materiobiology: A Perspective on Material-Guided Cell Behaviors and Tissue Engineering. Chem Rev 2017; 117:4376-4421. [PMID: 28221776 DOI: 10.1021/acs.chemrev.6b00654] [Citation(s) in RCA: 345] [Impact Index Per Article: 49.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 02/07/2023]
Abstract
Although the biological functions of cell and tissue can be regulated by biochemical factors (e.g., growth factors, hormones), the biophysical effects of materials on the regulation of biological activity are receiving more attention. In this Review, we systematically summarize the recent progress on how biomaterials with controllable properties (e.g., compositional/degradable dynamics, mechanical properties, 2D topography, and 3D geometry) can regulate cell behaviors (e.g., cell adhesion, spreading, proliferation, cell alignment, and the differentiation or self-maintenance of stem cells) and tissue/organ functions. How the biophysical features of materials influence tissue/organ regeneration have been elucidated. Current challenges and a perspective on the development of novel materials that can modulate specific biological functions are discussed. The interdependent relationship between biomaterials and biology leads us to propose the concept of "materiobiology", which is a scientific discipline that studies the biological effects of the properties of biomaterials on biological functions at cell, tissue, organ, and the whole organism levels. This Review highlights that it is more important to develop ECM-mimicking biomaterials having a self-regenerative capacity to stimulate tissue regeneration, instead of attempting to recreate the complexity of living tissues or tissue constructs ex vivo. The principles of materiobiology may benefit the development of novel biomaterials providing combinative bioactive cues to activate the migration of stem cells from endogenous reservoirs (i.e., cell niches), stimulate robust and scalable self-healing mechanisms, and unlock the body's innate powers of regeneration.
Collapse
Affiliation(s)
- Yulin Li
- Key Laboratory for Ultrafine Materials of Ministry of Education, East China University of Science and Technology , Meilong Road 130, Shanghai 200237, People's Republic of China
| | - Yin Xiao
- Institute of Health and Biomedical Innovation, Queensland University of Technology , Kelvin Grove, Brisbane, Queensland 4059, Australia
| | - Changsheng Liu
- Key Laboratory for Ultrafine Materials of Ministry of Education, East China University of Science and Technology , Meilong Road 130, Shanghai 200237, People's Republic of China
| |
Collapse
|
9
|
Bakola V, Karagkiozaki V, Pappa F, Tsiapla A, Pavlidou E, Moutsios I, A.Laskarakis, Logothetidis S. Drug Delivery Nanosystems for Cardiovascular Stents. ACTA ACUST UNITED AC 2017. [DOI: 10.1016/j.matpr.2017.07.016] [Citation(s) in RCA: 5] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/26/2022]
|
10
|
Nandakumar D, Bendavid A, Martin PJ, Harris KD, Ruys AJ, Lord MS. Fabrication of Semiordered Nanopatterned Diamond-like Carbon and Titania Films for Blood Contacting Applications. ACS APPLIED MATERIALS & INTERFACES 2016; 8:6802-6810. [PMID: 26928086 DOI: 10.1021/acsami.5b11614] [Citation(s) in RCA: 9] [Impact Index Per Article: 1.1] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/05/2023]
Abstract
Biomaterials with the ability to interface with, but not activate, blood components are essential for a multitude of medical devices. Diamond-like carbon (DLC) and titania (TiO2) have shown promise for these applications; however, both support platelet adhesion and activation. This study explored the fabrication of nanostructured DLC and TiO2 thin film coatings using a block copolymer deposition technique that produced semiordered nanopatterns with low surface roughness (5-8 nm Rrms). These surfaces supported fibrinogen and plasma protein adsorption that predominantly adsorbed between the nanofeatures and reduced the overall surface roughness. The conformation of the adsorbed fibrinogen was altered on the nanopatterned surfaces as compared with the planar surfaces to reveal higher levels of the platelet binding region. Planar DLC and TiO2 coatings supported less platelet adhesion than nanopatterned DLC and TiO2. However, platelets on the nanopatterned DLC coatings were less spread indicating a lower level of platelet activation on the nanostructured DLC coatings compared with the planar DLC coatings. These data indicated that nanostructured DLC coatings may find application in blood contacting medical devices in the future.
Collapse
Affiliation(s)
- Deepika Nandakumar
- Biomedical Engineering, School of AMME, University of Sydney , Sydney, New South Wales 2007, Australia
| | - Avi Bendavid
- Material Science and Engineering, CSIRO , Lindfield, New South Wales 2070, Australia
| | - Philip J Martin
- Material Science and Engineering, CSIRO , Lindfield, New South Wales 2070, Australia
| | - Kenneth D Harris
- National Institute for Nanotechnology, National Research Council , Edmonton, Alberta T5B 0N1, Canada
| | - Andrew J Ruys
- Biomedical Engineering, School of AMME, University of Sydney , Sydney, New South Wales 2007, Australia
| | - Megan S Lord
- Graduate School of Biomedical Engineering, University of New South Wales , Sydney, New South Wales 2052, Australia
| |
Collapse
|
11
|
Fernandez-Yague MA, Larrañaga A, Gladkovskaya O, Stanley A, Tadayyon G, Guo Y, Sarasua JR, Tofail SAM, Zeugolis DI, Pandit A, Biggs MJ. Effects of Polydopamine Functionalization on Boron Nitride Nanotube Dispersion and Cytocompatibility. Bioconjug Chem 2015; 26:2025-37. [PMID: 26282841 DOI: 10.1021/acs.bioconjchem.5b00257] [Citation(s) in RCA: 35] [Impact Index Per Article: 3.9] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/17/2023]
Abstract
Boron nitride nanotubes (BNNTs) have unique physical properties, of value in biomedical applications; however, their dispersion and functionalization represent a critical challenge in their successful employment as biomaterials. In the present study, we report a process for the efficient disentanglement of BNNTs via a dual surfactant/polydopamine (PD) process. High-resolution transmission electron microscopy (HR-TEM) indicated that individual BNNTs become coated with a uniform PD nanocoating, which significantly enhanced dispersion of BNNTs in aqueous solutions. Furthermore, the cytocompatibility of PD-coated BNNTs was assessed in vitro with cultured human osteoblasts (HOBs) at concentrations of 1, 10, and 30 μg/mL and over three time-points (24, 48, and 72 h). In this study it was demonstrated that PD-functionalized BNNTs become individually localized within the cytoplasm by endosomal escape and that concentrations of up to 30 μg/mL of PD-BNNTs were cytocompatible in HOBs cells following 72 h of exposure.
Collapse
Affiliation(s)
| | - Aitor Larrañaga
- Department of Mining-Metallurgy Engineering and Materials Science & POLYMAT, School of Engineering, University of the Basque Country (UPV/EHU) , 480130 Bilbao, Spain
| | | | - Alanna Stanley
- Department of Anatomy, National University of Ireland Galway (NUIG) , Galway, Ireland
| | | | - Yina Guo
- Department of Physics and Energy, and Materials and Surface Science Institute (MSSI), University of Limerick , Limerick, Ireland
| | - Jose-Ramon Sarasua
- Department of Mining-Metallurgy Engineering and Materials Science & POLYMAT, School of Engineering, University of the Basque Country (UPV/EHU) , 480130 Bilbao, Spain
| | - Syed A M Tofail
- Department of Physics and Energy, and Materials and Surface Science Institute (MSSI), University of Limerick , Limerick, Ireland
| | | | | | | |
Collapse
|
12
|
Forgerini FL, Marchiori R. A brief review of mathematical models of thin film growth and surfaces. A possible route to avoid defects in stents. BIOMATTER 2014; 4:e28871. [PMID: 25482417 PMCID: PMC4122570 DOI: 10.4161/biom.28871] [Citation(s) in RCA: 18] [Impact Index Per Article: 1.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Indexed: 11/25/2022]
Abstract
The morphology of thin films has been extensively studied in the last years. The properties of a thin film are closely related to its microstructure, especially to its morphology and surface roughness. Optical reflectivity, conductivity, and porosity are characteristics that depend on the film structure. The knowledge of atomistic details of the thin film growth process is useful for the development of new techniques and the control of thin films and new materials. Models of growth process are very powerful tools that can help researchers to predict and control physical, chemical, and mechanical properties. In this work we briefly summarize the theoretical models that have been used in the studies of thin films growth. By describing the deposition process of atoms/molecules on the surface of the substrate, one can study the evolution of the bulk and the surface roughness of a thin film. If an experimental growth process is appropriately described by a theoretical model (or even a combination of one or more different models), it can also provide indications to control the surface roughness and porosity of the film. Controlling the growth process one can obtain materials with a set of desired properties, namely tribological, porosity, and electrical ones. These characteristics are necessary for example, for hosting a solid lubricant on the surface of the material. We believe that the models presented in this work can be very useful in understanding the mechanisms of control and adherence of electrodeposited films which are commonly used in medical applications such as stent devices. We also believe that the models can be helpful to the understanding surface problems related to the superficial defects in stents.
Collapse
|
13
|
Stapleton PA, Nurkiewicz TR. Vascular distribution of nanomaterials. WILEY INTERDISCIPLINARY REVIEWS-NANOMEDICINE AND NANOBIOTECHNOLOGY 2014; 6:338-48. [PMID: 24777845 DOI: 10.1002/wnan.1271] [Citation(s) in RCA: 31] [Impact Index Per Article: 3.1] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 12/19/2013] [Revised: 03/19/2014] [Accepted: 03/29/2014] [Indexed: 02/06/2023]
Abstract
UNLABELLED Once considered primarily occupational, novel nanotechnology innovations, and applications have led to widespread domestic use and intentional biomedical exposures. With these exciting advances, the breadth and depth of toxicological considerations must also be expanded. The vascular system interacts with every tissue in the body, striving to maintain homeostasis. Engineered nanomaterials (ENM) have been reported to distribute in many different tissues and organs. However, these observations have tended to use approaches requiring tissue homogenization and/or gross organ analyses. These techniques, while effective in establishing presence, preclude an exact determination of where ENM are deposited within a tissue. If nanotechnology is to achieve its full potential, it is necessary to identify this exact distribution and deposition of ENM throughout the cardiovascular system, with respect to vascular hemodynamics and in vivo ENM modifications taken into account. Distinct levels of the vasculature will first be described as individual compartments. Then the vasculature will be considered as a whole. These unique compartments and biophysical conditions will be discussed in terms of their propensity to favor ENM deposition. Understanding levels of the vasculature will also be discussed. Ultimately, future studies must verify the mechanisms speculated on and presented herein. CONFLICT OF INTEREST The authors have declared no conflicts of interest for this article. For further resources related to this article, please visit the WIREs website.
Collapse
Affiliation(s)
- Phoebe A Stapleton
- Center for Cardiovascular and Respiratory Sciences, West Virginia University School of Medicine, Morgantown, WV, USA; Department of Physiology and Pharmacology, West Virginia University School of Medicine, Morgantown, WV, USA
| | | |
Collapse
|