Effective adsorption of nickel (II) with Ulva lactuca dried biomass: isotherms, kinetics and mechanisms

Dynamic Removal of Nickel (II) on Elaeis guineensis Waste Bed: Study of the Breakage Curve and Simulation

This research focused on the use of residual fiber from oil palm (Elaeis guineensis) for Ni (II) adsorption in a packed bed column. An analysis was conducted on the effect and statistical incidence of changes in temperature, adsorbent particle size, and bed height on the adsorption process. The results showed that particle size and bed height significantly affect the adsorption of Ni (II) ions, reaching adsorption efficiencies between 87.24 and 99.86%. A maximum adsorption capacity of 13.48 mg/g was obtained in the bed with a break time of 180 min. The Ni (II) adsorption in the dynamic system was evaluated by the analysis of the breakage curve with different theoretical models: Yoon-Nelson, dose-response, and Adams-Bohart; the dose-response model was the most appropriate to describe the behavior of the packed bed with an R² of 84.56%. The breakthrough curve obtained from Aspen Adsorption^® appropriately describes the experimental data with an R² of 0.999. These results indicate that the evaluated bioadsorbent can be recommended for the elimination of Ni (II) in aqueous solutions in a dynamic system, and the simulation of the process can be a tool for the scalability of the process.

Mn(II) Sorption on Stream Sediments Sampled in Manganese Mining Area: Dynamics and Mechanisms

The stream sediments that have been impacted by manganese (Mn) containing wastewater for decades contain not only abundant microorganisms but also organic/inorganic substances. To achieve effective treatment of manganese (Mn)-containing effluent and recovery of Mn from water/sediments, the Mn(II) sorption behaviors and mechanism on sediments of a stream in Mn mining areas were studied. In addition, the study analyzed the effects of various factors (initial concentration, solution pH, sediment dose, contact time, and coexisting cations) on the Mn sorption efficiency of Daxin sediments, and explored the contribution of microbial activity in the sediment sorption of Mn(II). The results showed that the sorption process of Mn(II) on the sediments was consistent with the Elovich and Freundlich models, and the removal of heavy metals was maximum at 40 °C (62.47–98.93%), pH = 8 (77.51%), initial concentration of 1 mmol·L−1 (95.37%) and sediment dosing of 12 g·L−1 (98.93%). The addition of 50 mM NaN3 inhibited the microbial activity in the Daxin sediment, reducing the sorption and removal rates of Mn(II) by 0.605 mg·g−1 and 8.92%, respectively. After sorption, the proportion of the Fe–Mn oxidation(iron–manganese) state in Daxin sediments decreased from 54% to 43%, while the proportion of the exchangeable state increased by 10.80%. Microorganisms in the sediment had a positive effect on inhibiting heavy metal migration and reducing the bioavailability of contaminants in the soil. Through this study, we hope to further understand the sorption and desorption mechanism of manganese by stream sediments in manganese ore areas, so as to provide a guide on the management and recovery of Mn from stream sediments in manganese mining areas.

Lead removal from synthetic wastewater by biosorbents prepared from seeds of Artocarpus Heterophyllus and Syzygium Cumini

The present investigation deals with removal of lead (Pb⁺²) ions from waste water using biosorbent prepared from seeds of Artocarpus heterophyllus (SBAh) and Syzygium cumini (SBSc). Biosorbents surface has been characterized through FT-IR spectroscopy to probe the presence of functional groups. Response surface methodology enabled optimized conditions (Pb⁺² concentration 2 μg/mL, pH 5.8 and bioadsorbent dose 60 mg) resulted in Pb⁺² removal ~96% for SBAh and ~93% for SBSc at agitation speed 300 rpm. The adsorption capacity has been found to be 4.93 mg/g for SBAh and 3.95 mg/g for SBSc after 70 min. At optimal experimental conditions, kinetics of biosorption was explained well by inter-particle diffusion model for SBAh (R² = 0.99) whereas Elovich model best fitted for SBSc (R² = 0.98). Further, both the biosorbents followed Temkin adsorption isotherm model.

Ulva lactuca: A bioindicator for anthropogenic contamination and its environmental remediation capacity

Coastal regions are subjected to degradation due to anthropogenic pollution. Effluents loaded with variable concentrations of heavy metal, persistent organic pollutant, as well as nutrients are discharged in coastal areas leading to environmental degradation. In the past years, many scientists have studied, not only the effect of different contaminants on coastal ecosystems but also, they have searched for organisms tolerant to pollutants that can be used as bioindicators or for biomonitoring purposes. Furthermore, many researchers have demonstrated the capacity of different marine organisms to remove heavy metals and persistent organic pollutants, as well as to reduce nutrient concentration, which may lead to eutrophication. In this sense, Ulva lactuca, a green macroalgae commonly found in coastal areas, has been extensively studied for its capacity to accumulate pollutants; as a bioindicator; as well as for its remediation capacity. This paper aims to review the information published regarding the use of Ulva lactuca in environmental applications. The review was focused on those studies that analyse the role of this macroalga as a biomonitor or in bioremediation experiments.

Nickel Removal from Aqueous Solution Using Chemically Treated Mahogany Sawdust as Biosorbent

Sawdust is a waste material, which is generally produced during making furniture and other necessary wood products. With a view to utilizing this waste material, a biosorbent was prepared from mahogany (Swietenia macrophylla) sawdust through simple chemical treatment and was used to remove nickel ion (Ni2+) from an aqueous solution. The adsorbent material was characterized by Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and energy dispersive X-ray (EDX) analysis. The effects of biosorbent dosage (2∼18 g/L), pH of the tested solution (4∼10.5), contact time (up to 360 min), and temperature (298∼318 K) were studied in batchwise experiments. The maximum adsorption capacity of the treated sawdust was determined to be 13.42 mg/g at an optimum condition (sorbent dose of 15 g/L, pH of 9, and temperature of 298 K). The experimental data extrapolation revealed that the adsorption process fitted the Langmuir isotherm model and the kinetics was a pseudo-second-order kinetic model. The obtained thermodynamic parameters indicated that the adsorption reaction was spontaneous, endothermic, and random in nature. The study revealed that sawdust biosorbent has potential adsorption efficiency for nickel ion removal from an aqueous solution.

Comparison of Heavy Metals Removal from Aqueous Solution by Moringa oleifera Leaves and Seeds

In this work, biomass obtained from seeds (S-MO) and leaves (L-MO) of the Moringa oleifera plant were used as low-cost biosorbents to remove the Pb(II), Cd(II), Co(II), and Ni(II) from aqueous solutions. The biosorption of the heavy metal ions was done using the batch technique. The effects of contact time (30–1440 min), biosorbent dosage (10–50 g/L) (0.1–0.5 g), and initial concentration of metals (10–500 mg/L) on the sorption capacity of metal ions were investigated. The S-MO and L-MO samples’ characterization was performed using pHpzc, X-ray Diffraction (XRD), and Fourier Transform Infrared Spectroscopy (FTIR). It was found that the pHpzc was notably different between the seeds and leave-derived biosorbents. The removal process’s experimental kinetic data for both S-MO and L-MO were best described by the pseudo-second-order model for all metal ions, with R2 above 0.997 in all cases. Langmuir and Freundlich’s models were also used to analyze the isotherms parameters. Based on the Langmuir model, the maximum sorption capacities (Qm) for L-MO were found as follows: L-MO-Pb > L-MO-Cd > L-MO-Co ≥ L-MO-Ni, and for S-MO, the values of Qm values presented the following order: S-MO-Pb > S-MO-Co > S-MO-Cd > S-MO-Ni.

Mg17Al12 phase in magnesium alloy waste facilitating the Ni2+ reduction in nickel plating wastewater

A process for recycling Ni²⁺ in Ni-plating wastewater was investigated. This study employed Mg alloy flash waste to reduce the Ni²⁺ in the wastewater into metallic Ni. Fine second-phase Mg₁₇Al₁₂ in a network is the critical point for promoting the reduction reaction of Ni²⁺. The microstructures of the Mg alloy flash scrap and the die-cast Mg alloy scrap waste fulfilled the requirement. The Mg₁₇Al₁₂ is like a catalyst for the quick reduction of the Ni²⁺ ions into pure Ni metal. Contrarily, pure Mg (not containing Mg₁₇Al₁₂ particles) and gravity-cast AZ91D Mg alloy (having coarse Mg₁₇Al₁₂ particles) were not suitable for being used for the Ni²⁺ wastewater treatment. Based on the above results and discussion, using the Mg alloy flash scrap waste for treating the laboratory-made Ni²⁺-containing wastewater, the wastewater initially with ∼5600 ppm of Ni²⁺ ions could be reduced to ∼20 ppm in 2 h. When applying the Mg alloy flash scrap for the Ni plating wastewater from industry, the concentration of Ni²⁺ was able to be reduced from ∼16,670 ppm to ∼1434 ppm in 10 min for the wastewater at 90 °C.

New alginate-based interpenetrating polymer networks for water treatment: A response surface methodology based optimization study

Different interpenetrating polymeric networks (IPN) based on sodium alginate, carrageenan and bentonite were developed to remove heavy metals and dyes from contaminated water. Four significant preparation factors; crosslinking time, calcium chloride concentration, alginate to carrageenan mass ratio,and bentonite to carrageenan mass ratio were studied and optimized via full factorial design and response surface methodology to determine the optimum composition with highest adsorption capacity. Different optimal conditions and combinations were found depending on the type of heavy metal or dye to be removed. Low calcium chloride concentration was a common factor in all cases of heavy metals and dyes removal which indicates the negative effect of excessive crosslinking on the removal percentage. The adsorption capacity of methylene blue, Fe³⁺, Ni²⁺, and Cr³⁺ ions is 1271, 1550, 1500 and 1540 mg/g adsorbent, respectively. Reusability tests confirmed that the optimized formulations can be reused five successive times without significant drop in their removal efficiency. Upon utilization of the optimized formulations on real contaminated waters from tannery plant and oasis groundwater, they demonstrated an excellent performance as they removed above 95% of the original heavy metals contaminants and 40% of the acidic dye content.

Removal of thallium from environmental samples using a raw and chemically modified biosorbent derived from domestic wastes

Because of its high toxicity, thallium (Tl) causes environmental pollution even at very low concentrations. Despite its extremely high environmental risk, limited information about Tl removal from water is present on the literature. This work focused on the use of an eco-friendly and low-cost Ilex paraguariensis (yerba mate) biowaste to remove Tl from environmental water samples. Raw (YM) and L-cysteine chemically modified yerba mate (YM@LC) were used. The effect of pH and biosorbent concentration on the biosorption capacity was studied using an experimental design. The optimal experimental conditions were as follows: YM concentration 0.25 g L^-1, pH 6.0, and YM@LC concentration 0.25 g L^-1, pH 4.0. Kinetic studies yielded data that were in accordance with pseudo-second-order model. Equilibrium studies were also developed and indicated that the most appropriate model was that of Sips, with a maximum capacity of biosorption at 328 K of 333.4 mg g^-1 for YM and 384.4 mg g^-1 for YM@LC. The thermodynamic evaluation exhibited an endothermic, spontaneous, and favorable biosorption for both biosorbents. YM and YM@LC showed significant potential for Tl removal from environmental water samples.