Synthesis of polyethersulfone (PES)/GO-SiO2 mixed matrix membranes for oily wastewater treatment

Synthesis of MOF-5/polyethersulfone (PES) mixed matrix membranes for enhancing membrane filtration performance in polyphenol purification

The various apple products industries produce a large amount of apple residue, which is easily fermented, causes environmental pollution, and its disposal cost is high, but is rich in nutrients, such as polyphenols. Polyphenols can be purified to realize high-value deep processing of apple pomace and to promote energy reuse of food waste. In this study, the highly selective purification of polyphenols was achieved by membrane filtration using prepared Metal-organic framework (MOF)-5/PES mixed matrix membranes with apple peels as raw material. The polyethersulfone mixed matrix membrane was loaded with MOF-5 by the phase inversion method, and their structural and physicochemical properties were characterized by scanning electron microscopy (SEM), and X-ray diffraction (XRD). Zeta potential and specific surface area of MOF-5 particles were measured, as well as the water contact angle and anti-fouling properties of the mixed matrix membrane were analyzed. It was confirmed that the membrane loaded with MOF-5 showed better hydrophilicity and mechanical properties compared with the pristine polyether sulfone membrane. Under practical conditions, the increased hydrophilicity could enhance the anti-fouling properties of membranes, which would improve the flux recovery ratio of membranes. In addition, the prepared MOF-5/PES mixed matrix membrane was applied to the purification of polyphenols, showing excellent purification performance of polyphenols. In particular, the purity of polyphenol after membrane filtration could reach 70.45% when the additional amount of MOF-5 was 10%. This research provides a method to prepare MOF-5/PES mixed matrix membranes, which effectively solves the problem of unstable and unsatisfactory purification effect of commercially available membranes, promotes the development of new materials in membrane science, and realizes high-value deep processing and comprehensive resource development of food waste using membrane filtration.

Preparation and Characterization of Polyethersulfone-Ultrafiltration Membrane Blended with Terbium-Doped Cerium Magnesium Aluminate: Analysis of Fouling Behavior

In this study, various techniques, including X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDS) mapping, X-ray photoelectron spectroscopy (XPS), and water-contact-angle goniometry (WCAG), were used to characterize the crystalline structure and morphological properties of terbium-doped cerium magnesium aluminate (Ce0.67Tb0.33MgAl11O19 or CMAT) in powder form. The results demonstrated that CMAT was successfully synthesized with a particle size of less than 5 µm and a fully evident distribution of elements, as revealed by the SEM images. This was further confirmed by the XRD and HRTEM images. XPS analysis confirmed the presence of all necessary components in CMAT. Additionally, WCAG results showed that the contact angle of CMAT was more hydrophilic with a value of 8.4°. To evaluate its performance, CMAT particles were dispersed in a Polyethersulfone (PES) solution and used to modify a PES ultrafiltration membrane through a phase-inversion method. The resulting membranes were characterized by SEM, atomic force microscopy (AFM), thermogravimetric analysis (TGA), WCAG, and permeability performance and fouling experiments. The addition of CMAT to the PES membranes did not have a significant effect on the structure of the SEM images of the top layer and cross-section of surface properties. However, increasing the concentration of CMAT improved the membrane surface roughness in AFM, and the modified membranes had the ability to resist fouling. The addition of CMAT did not lead to significant energy loss, indicating that the heat flux loss observed can indeed be explained by the amount of C-OH on the PES membrane’s surface. The contact angle of the membranes became more hydrophilic with increasing concentration of CMAT from PES G0 to PES G7. The PES origin membrane showed a higher permeation than the membranes mixed with CMAT, and the modified membranes with CMAT displayed significant fouling resistance.

Enhanced Antifouling in Flat-Sheet Polyphenylsulfone Membranes Incorporating Graphene Oxide-Tungsten Oxide for Ultrafiltration Applications

In this study tungsten oxide and graphene oxide (GO-WO_2.89) were successfully combined using the ultra-sonication method and embedded with polyphenylsulfone (PPSU) to prepare novel low-fouling membranes for ultrafiltration applications. The properties of the modified membranes and performance were investigated using Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), contact angle (CA), water permeation flux, and bovine serum albumin (BSA) rejection. It was found that the modified PPSU membrane fabricated from 0.1 wt.% of GO-WO_2.89 possessed the best characteristics, with a 40.82° contact angle and 92.94% porosity. The permeation flux of the best membrane was the highest. The pure water permeation flux of the best membrane showcased 636.01 L·m^-2·h^-1 with 82.86% BSA rejection. Moreover, the membranes (MR-2 and MR-P2) manifested a higher flux recovery ratio (FRR %) of 92.66 and 87.06%, respectively, and were less prone to BSA solution fouling. The antibacterial performance of the GO-WO_2.89 composite was very positive with three different concentrations, observed via the bacteria count method. These results significantly overtake those observed by neat PPSU membranes and offer a promising potential of GO-WO_2.89 on activity membrane performance.

Technological trends in nanosilica synthesis and utilization in advanced treatment of water and wastewater

Water and wastewater treatment applications stand to benefit immensely from the design and development of new materials based on silica nanoparticles and their derivatives. Nanosilica possesses unique properties, including low toxicity, chemical inertness, and excellent biocompatibility, and can be developed from a variety of sustainable precursor materials. Herein, we provide an account of the recent advances in the synthesis and utilization of nanosilica for wastewater treatment. This review covers key physicochemical aspects of several nanosilica materials and a variety of nanotechnology-enabled wastewater treatment techniques such as adsorption, separation membranes, and antimicrobial applications. It also discusses the prospective design and tuning options for nanosilica production, such as size control, morphological tuning, and surface functionalization. Informative discussions on nanosilica production from agricultural wastes have been offered, with a focus on the synthesis methodologies and pretreatment requirements for biomass precursors. The characterization of the different physicochemical features of nanosilica materials using critical surface analysis methods is discussed. Bio-hybrid nanosilica materials have also been highlighted to emphasize the critical relevance of environmental sustainability in wastewater treatment. To guarantee the thoroughness of the review, insights into nanosilica regeneration and reuse are provided. Overall, it is envisaged that this work's insights and views will inspire unique and efficient nanosilica material design and development with robust properties for water and wastewater treatment applications.

Controlled synthesis of graphene oxide/silica hybrid nanocomposites for removal of aromatic pollutants in water

The remarkable characteristics of graphene make it a model candidate for boosting the effectiveness of nano-adsorbents with high potential owing to its large surface area, π–π interaction, and accessible functional groups that interact with an adsorbate. However, the stacking of graphene reduces its influence adsorption characteristics and also its practical application. On the other hand, the widespread use of aromatic compounds in the industry has aggravated the contamination of the water environment, and how to effectively remove them has become a research hotspot. Herein, we develop the functionalization of silica nanoparticles on graphene oxide nanosheet (FGS) by a facile, cheap, and efficient synthesis protocol for adsorption of Trypan Blue (TB) and Bisphenol A (BPA). It was demonstrated that chemical activation with KOH at high autoclaving temperature successfully transformed rice husk ash (RHA) into FGS. The graphene oxide layered interlamination was kept open by using SiO₂ to expose the interlayers' strong adsorption sites. XRD, EDX, FTIR, Raman spectroscopy, SEM, HR-TEM, and BET surface area are used to investigate the chemical composition, structure, morphology, and textural nature of the as-produced FGS hybrid nanocomposite. The various oxygen-containing functional groups of the hybrid nanocomposites resulted in a significantly increased adsorption capacity, according to experimental findings. In addition, FGS2, the best composite, has a specific surface area of 1768 m²g⁻¹. Based on Langmuir isotherms, the maximal TB dye and BPA removal capacity attained after 30 min were 455 and 500 mg/g, respectively. The Langmuir isotherm model, a pseudo-second-order kinetic model, and an intraparticle diffusion model have all been used to provide mechanistic insights into the adsorption process. This suggests that BPA and TB adsorption on FGS2 is mostly chemically regulated monolayer adsorption. Due to its unique sp²-hybridized single-atom-layer structure, the exposed graphene oxide nanosheets' extremely hydrophobic effect, hydrogen bonding, and strong—electron donor–acceptor interaction contributed to their improved adsorption of BPA and TB. According to adsorption thermodynamics, FGS2 adsorption of TB and BPA is a spontaneous exothermic reaction that is aided by lowering the temperature. For adsorption-based wastewater cleanup, the produced nanocomposites with a regulated amount of carbon and silica in the form of graphene oxide and silica can be used. These findings suggest that functionalized GO/SiO₂ hybrid nanocomposites could be a viable sorbent for the efficient and cost-effective removal of aromatic chemicals from wastewater.

Modification of polyethersulfone membranes by Polyethyleneimine (PEI) grafted Silica nanoparticles and their application for textile wastewater treatment

In the current work, a novel nanocomposite membrane for wastewater treatment applications has been synthesized. A hydrophilic nature nanoadditive comprised grafting polyethylenimine (PEI) molecules onto the surfaces of silica nanoparticles (SiO₂ NPs) was synthesized then entrapped within a polyethersulfone polymeric matrix at disparate ratios via the classical phase inversion technique. A series of experimental tools were employed to probe the influence of SiO₂-PEI on the surface topography and morphological changes, hydrophilicity, porosity, surface chemistry as well as permeation and dyes retention characteristics of the new nanocomposite. Upon increasing the nanoadditives content (up to 0.7 wt. % SiO₂- PEI), clear cross-sectional changes were depicted along with a noticeable decline in the water contact angle by 29.7%. Performance evaluation measurements against synthetic dye solutions were disclosed explicit enhancement in both; retention and permeation characteristics of the nanocomposite membranes. Besides, prolonged permeation test has maintained high flux stability against real textile wastewater; implying better resistance and self-cleaning characteristics have been achieved.

Recent advances in dual-filler mixed matrix membranes

Mixed matrix membranes (MMMs) have been widely developed as an attractive solution to overcome the drawbacks found in most polymer membranes, such as permeability-selectivity trade-off and low physicochemical stability. Numerous fillers based on inorganic, organic, and hybrid materials with various structures including porous or nonporous, and two-dimensional or three-dimensional, have been used. Demanded to further improve the characteristics and performances of the MMMs, the use of dual-filler instead of a single filler has then been proposed, from which multiple effects could be obtained. This article aims to review the recent development of MMMs with dual filler and discuss their performances in diverse potential applications. Challenges in this emerging field and outlook for future research are finally provided.

Graphene oxide-reinforced poly (ether-ether-ketone)/silica composites with improved mechanical performance and surface bioactivity

The control of interfacial interaction between polymers and fillers is essential for the fabrication of high-performance polymer composites. In this work, poly(ether-ether-ketone)/silica (PEEK/SiO₂) and PEEK/SiO₂/graphene oxide (GO) composite were prepared by ball milling-ultrasonic dispersion combined with melt extrusion injection molding. GO nanosheets were introduced as the interfacial enhancer to improve interfacial binding between SiO₂ and PEEK. Mechanical tests showed that the incorporation of SiO₂ and GO greatly optimized the modulus, strength, and fracture toughness of the composites. The tensile strength and Young's modulus of the PEEK/SiO₂ composites increases with the increase of SiO₂ content. The maximum tensile strength and Young's modulus of the PEEK/SiO₂ composites are approximate 95.9 ± 0.6 MPa and 4.007 ± 0.005 GPa at 30 wt% of SiO₂, an increase of 6.4% and 21.2% than that of pure PEEK. The maximum tensile strength and Young's modulus of the PEEK/SiO₂/GO composite are further improved to approximate 101.5 ± 0.7 MPa and 4.62 ± 0.08 GPa at a GO content of 1.5% wt, which is 12.6% and 39.4% higher than that of pure PEEK. In addition, SEM images show that numerous HA formed on the surface of the PEEK/SiO₂/GO composite after immersion in SBF for 7 days, and the HA layer becomes gradually thicker after 14 days, implying the good osteogenic activity of PEEK/SiO₂/GO composites. Therefore, these results suggest that the use of GO as a novel filler surface modifier for the preparation of high-performance composites may become a novel interfacial design strategy for the development of high-performance composites.

A Mini-Review of Enhancing Ultrafiltration Membranes (UF) for Wastewater Treatment: Performance and Stability

The scarcity of freshwater resources in many regions of the world has contributed to the emergence of various technologies for treating and recovering wastewater for reuse in industry, agriculture, and households. Deep wastewater treatment from oils and petroleum products is one of the difficult tasks that must be solved. Among the known technologies, UF membranes have found wide industrial application with high efficiency in removing various pollutants from wastewater. It is shown that the search for and development of highly efficient, durable, and resistant to oil pollution UF membranes for the treatment of oily wastewater is an urgent research task. The key parameters to improve the performance of UF membranes are by enhancing wettability (hydrophilicity) and the antifouling behavior of membranes. In this review, we highlight the using of ultrafiltration (UF) membranes primarily to treat oily wastewater. Various methods of polymer alterations of the UF membrane were studied to improve hydrophilicity, the ability of antifouling the membrane, and oil rejection, including polymer blending, membrane surface modification, and the mixed membrane matrix. The influence of the type and composition of the hydrophilic additives of nanoparticles (e.g., Multiwall carbon nanotubes (MWCNT), graphene oxide (GO), zinc oxide (ZnO), and titanium dioxide (TiO2), etc.) was investigated. The review further provides an insight into the removal efficiency percent.

Halloysite Nanotube-Ferrihydrite Incorporated Polyethersulfone Mixed Matrix Membrane: Effect of Nanocomposite Loading on the Antifouling Performance

Membrane filtration is an attractive process in water and wastewater treatment, but largely restricted by membrane fouling. In this study, the membrane fouling issue is addressed by developing polyethersulfone (PES)-based mixed matrix membranes (MMMs) with the incorporation of hydrophilic nanoparticles as an additive. Ultrafiltration MMMs were successfully fabricated by incorporating different loadings of halloysite nanotube-ferrihydrates (HNT-HFO) into a polyethersulfone (PES) matrix and their performance was evaluated for the separation of bovine serum albumin (BSA) solution and oil/water emulsion. The results show that wettability is endowed to the membrane by introducing the additive aided by the presence of abundant -OH groups from the HFO. The loading of additive also leads to more heterogeneous surface morphology and higher pure water fluxes (516.33-640.82 L/m2h) more than twice that of the pristine membrane as reference (34.69 L/m2h) without affecting the rejection. The MMMs also provide much enhanced antifouling properties. The filtration results indicate that the flux recovery ratio of the modified membrane reached 100% by washing with only distilled water and a total flux recovery ratio of >98% ± 0.0471 for HNT-HFO-loaded membranes in comparison with 59% ± 0.0169 for pristine PES membrane.