No positive effect of Acid etching or plasma cleaning on osseointegration of titanium implants in a canine femoral condyle press-fit model

Critical Role of Etching Parameters in the Evolution of Nano Micro SLA Surface on the Ti6Al4V Alloy Dental Implants

The surface of dental implants plays a vital role in early and more predictable osseointegration. SLA (sandblasted large grit and acid-etched) represents the most widely accepted, long-term clinically proven surface. Primarily, dental implants are manufactured by either commercially pure titanium (CP-Ti) or Ti6Al4V ELI alloy. The acid etch behavior of CP-Ti is well known and its effects on the surface microstructure and physicochemical properties have been studied by various researchers in the past. However, there is a lack of studies showing the effect of acid etching parameters on the Ti6Al4V alloy surface. The requirement of the narrow diameter implants necessitates implant manufacturing from alloys due to their high mechanical properties. Hence, it is necessary to have an insight on the behavior of acid etching of the alloy surface as it might be different due to changed compositions and microstructure, which can further influence the osseointegration process. The present research was carried out to study the effect of acid etching parameters on Ti6Al4V ELI alloy surface properties and the optimization of process parameters to produce micro- and nanotopography on the dental implant surface. This study shows that the Ti6Al4V ELI alloy depicts an entirely different surface topography compared to CP-Ti. Moreover, the surface topography of the Ti6Al4V ELI alloy was also different when etching was done at room temperature compared to high temperature, which in turn affected the behavior of the cell on these surfaces. Both microns and nano-level topography were achieved through the optimized parameters of acid etching on Ti6Al4V ELI alloy dental implant surface along with improved roughness, hydrophilicity, and enhanced cytocompatibility.

Acellular mineralized allogenic block bone graft does not remodel during the 10 weeks following concurrent implant placement in a rabbit femoral model

OBJECTIVES

Due to bone loss, endosseous implants often require addition of a bone graft to support adequate primary fixation, bone regeneration, and osseointegration. The aim of this study was to compare effectiveness of autogenic and allogenic bone grafts when used during simultaneous insertion of the implant.

MATERIALS AND METHODS

4-mm-diameter rabbit diaphyseal bone autografts or allografts (n = 16/group) with a 3.2-mm pre-drilled hole in the center were placed into a 4 mm defect in the proximal femur of 3.5 kg male New Zealand White rabbits. Machined 3.2 × 10 mm grit-blasted, acid-etched titanium-aluminum-vanadium (Ti6Al4V) implants were placed. Control implants were placed into progressively drilled 3.2-mm holes in the contralateral limbs. Post-insertion day 70, samples were analyzed by micro-CT and calcified histology, or by mechanical torque and push-out testing followed by decalcified histology.

RESULTS

Both grafts were integrated with the native bone. Micro-CT showed less bone volume (BV) and bone volume/total volume (BV/TV) in the allograft group, but histology showed no differences in BV or BV/TV between groups. Allograft lacked living cells, whereas autograft was cellularized. No difference was found in maximum removal torque between groups. Compressive loading at the graft-to-bone interface was significantly lower in allograft compared with autograft groups.

CONCLUSIONS

There was less bone in contact with the implant and significantly less maximum compressive load in the allograft group compared with autograft. The allograft remained acellular as demonstrated by empty lacunae. Taken together, block allograft implanted simultaneously with an implant produces a poorer quality bone compared with autograft.

Strontium folic acid derivative functionalized titanium surfaces for enhanced osteogenic differentiation of mesenchymal stem cells in vitro and bone formation in vivo

The introduction of the bioactive strontium (Sr) element has become an attractive method in the design of bio-functional layers on titanium surfaces. However, there are still no effective solutions to some of the associated problems including the toxicity of free Sr²⁺ ions and the rapid and irreversible loss of the strontium element from the bio-functional layers. In this study, we successfully fabricated a bioactive layer on Ti substrates with a strontium folic acid derivative (FASr). About 3.11 at% Sr was incorporated into the Ti surface. The characterization results showed that FASr was stable over a long period of time and minimal free Sr²⁺ ions were detected in simulated body fluid (SBF). In the in vitro experiment, the FASr could significantly promote the cell adhesion, proliferation and osteogenic differentiation of mesenchymal stem cells (MSCs) over a short period. Furthermore, it could dramatically accelerate the bone formation around the implant. In vivo, a total of 30 7-week old male Sprague Dawley (SD) rats were applied for implantation tests. The results showed that this positive stimulatory effect became more evident in the later stages of the in vivo observation. This study provides an effective strategy for designing and optimizing Ti-based implants.

Local delivery of zoledronate from a poly (D,L-lactide)-Coating increases fixation of press-fit implants

Early secure fixation of total joint replacements is crucial for long-term survival. Antiresorptive agents such as bisphosphonates have been shown to increase implant fixation. We investigated whether local delivery of zoledronate from poly-D, L-lactide (PDLLA)-coated implants could improve implant fixation and osseointegration. Experimental titanium implants were bilaterally inserted press-fit into the proximal tibiae of 10 dogs. On one side the implant was coated with PDLLA containing zoledronate. The contralateral implant was uncoated and used as control. Observation period was 12 weeks. Implant fixation was evaluated with histomorphometry and biomechanical push-out test. We found an approximately twofold increase in all biomechanical parameters when comparing data from the zoledronate group with their respective controls. Histomorphometry showed increased amount of preserved bone and increased bone formation around the zoledronate implants. This study indicates that local delivery of zoledronate from a PDDLA coating has the potential to increase implant fixation.