Adsorptive-removal of Bromothymol Blue as Acidic-dye Probe from Water Solution Using Latvian Sphagnum Peat Moss: Thermodynamic Assessment, Kinetic and Isotherm Modeling

Design of chitosan/boehmite biocomposite for the removal of anionic and nonionic dyes from aqueous solutions: Adsorption isotherms, kinetics, and thermodynamics studies

This study introduces a chitosan/boehmite biocomposite as an efficient adsorbent for removing anionic Congo Red (CR) and non-ionic Bromothymol Blue (BTB) from water. Boehmite nanoparticles were synthesized using the Sol-gel method and then attached to chitosan particles using sodium tripolyphosphate through co-precipitation method. Characterized through FTIR, FE-SEM, BET, and XRD, the biosorbent displayed structural integrity with optimized pH conditions of 3 for CR and 4 for BTB, achieving over 90 % adsorption within 30 min. Pseudo second order kinetics model and Langmuir isotherm revealed monolayer sorption with capacities of 64.93 mg/g for CR and 90.90 mg/g for BTB. Thermodynamics indicated a spontaneous and exothermic process, with physisorption as the primary mechanism. The biosorbent demonstrated excellent performance and recyclability over five cycles, highlighting its potential for eco-friendly dye removal in contaminated waters.

High-Efficient Anionic Dyes Removal from Water by Cationic Polymer Brush Functionalized Magnetic Mesoporous Silica Nanoparticles

High efficiency removal of methyl orange (MO) and bromothymol blue (BT) dyes from contaminated water has been reported using magnetic mesoporous nanoparticles modified with cationic polymer brush (poly(2-methacryloyloxy)ethyl] trimethylammonium chloride solution) (Fe3O4-MSNs-PMETAC). Atom transfer radical polymerization (ATRP) was utilized to grow the polymer chains on the magnetic mesoporous silica nanoparticles. The chemical surface modifications were confirmed using IR, TGA, SEM and TEM. The results show that the obtained Fe3O4-MSNs-PMETAC materials were nearly spherical in shape with approximately 30 nm magnetic core, and silica shell thicknesses ranged from 135 to 250 nm. The adsorption performance of the material was found to be unaffected by the pH (3-9) of the media, with a removal efficiency of 100% for both dyes. The adsorption of BT and MO on the surface of Fe3O4-MSNs-PMETAC was found to follow Freundlich and Langmuir models, respectively. Since the synthesized nanocomposite materials exhibit an enhanced properties such as large maximum adsorption capacity, rapid synthesis process, and easy separation from solution, it could be an effective sorbent for the removal of other pollutants such as potentially toxic anionic elements (e.g., arsenate and chromate ions) from water and wastewater.

Kinetics and Mechanism Studies of Oxidation of Dibromothymolsulfonphthalein Toxic Dye by Potassium Permanganate in Neutral Media with the Synthesis of 2-Bromo-6-isopropyl-3-methyl-cyclohexa-2,5-dienone

The oxidation of 3',3″-dibromothymolsulfonphthalein (DBTS) in neutral medium by potassium permanganate multi-equivalent oxidant has been studied spectrophotometrically. Pseudo-first-order plots showed inverted S-shape throughout the entire course of the reaction. The initial rates were found to be relatively fast in the early stages, followed by a decrease in the oxidation rates over longer time periods in the slow stage. Under pseudo-first-order conditions where [DBTS] ≫ 10 [MnO₄ ^-], the experimental results showed a first-order dependence in [MnO₄ ^-] and fractional-first-order kinetics in the [DBTS] concentration. The formation of 1:1 coordination intermediate complex prior to the rate-determining step was revealed kinetically. In addition, the intermediate species involving complexes of Mn(V) coordination has been detected. The oxidation product of DBTS was identified by Fourier transform infrared spectroscopy, ultraviolet-visible spectrophotometry, and gas chromatography-mass analysis. The obtained results indicated the formation of 2-bromo-6-isopropyl-3-methyl-cyclohexa-2,5-dienone as a derivative oxidation of DBTS.

Utilization of Biomass Fly Ash for Improving Quality of Organic Dye-Contaminated Water

Development of innovative methodologies to convert biomass ash into useful materials is essential to sustain the growing use of biomass for energy production. Herein, a simple chemical modification approach is employed to functionalize biomass fly ash (BFA) with 3-aminopropyltriethoxy silane (APTES) to develop an inexpensive and efficient adsorbent for water remediation. The amine-functionalized BFA (BFA-APTES) was fully characterized by employing a range of characterization techniques. Adsorption behavior of BFA-APTES was evaluated against two anionic dyes, namely, alizarin red S (ARS) and bromothymol blue (BTB). In the course of experimental data analysis, the computation tools of data fitting for linear and nonlinear form of Langmuir, Freundlich, and the modified Langmuir-Freundlich adsorption isotherms were used with the aid of Matlab R2019b. In order to highlight the misuse of linearization of adsorption models, the sum of the squares of residues (SSE) values obtained from nonlinear models are compared with R 2 values obtained from the linear regression. The accuracy of the data fitting was checked by the use of SSE as an error function instead of the coefficient of determination, R 2. The dye adsorption capacity of BFA-APTES was also compared with the nonfunctionalized BFA. The maximum adsorption capacities of BFA-APTES for ARS and BTB dye molecules were calculated to be around 13.42 and 15.44 mg/g, respectively. This value is approximately 2-3 times higher than the pristine BFA. A reasonable agreement between the calculated and experimental values of q e obtained from the nonlinear form of kinetic models verified the importance of using equations in their original form. The experimentally calculated thermodynamic parameters including molar standard Gibbs free energy (Δad G m 0) and molar standard enthalpy change (Δad H m 0) reflected that the process of adsorption of dye molecules on the BFA-APTES adsorbent was spontaneous and exothermic in nature. Moreover, the used BFA-APTES adsorbent could be regenerated and reused for several cycles with significant dye adsorption capacity. The remediation capability of the BFA-APTES adsorbent against ARS dye was also demonstrated by packing a small column filled with the BFA-APTES adsorbent and passing a solution of ARS through it. Overall, we provide a simple and scalable route to convert BFA into an efficient adsorbent for water remediation applications.