Clinical evaluation of monolithic zirconia crowns: a failure analysis of clinically obtained cases from a 3.5-year study

Load-bearing capacity of 3D-printed incisor partial-coverage crowns made from zirconia and composite

PURPOSE

This study investigated the fracture resistance of 0.5-mm-thick restorations for minimally invasive therapy. Anterior partial-coverage crowns composed of three-dimensional (3D)-printed 3-mol% yttria-stabilized tetragonal zirconia polycrystal (3Y-TZP; Lithacon 3Y210, Lithoz) and 3D-printed composite (Varseo Smile Crown plus, Bego) were compared with a control group made from milled 3Y-TZP (Cercon ht, DentsplySirona).

METHODS

Three groups each with 27 restorations were produced. For milled 3Y-TZP partial-coverage crowns, drill compensation was needed so the milling bur could access the inner surface at the incisal edge. Restoration fit was verified by cross-sectioning 12 specimens in each group. The remaining 15 restorations were sandblasted (Al2O3, 0.1 MPa) and adhesively cemented (Panavia SA, Kuraray) onto CoCr teeth. Static load-to-failure tests were performed. The load was induced on the incisal edge. The forces needed to fracture the specimens were analyzed using the Welch analysis of variance and post hoc Dunnet-T3 tests. The Weibull parameters were also calculated.

RESULTS

Drill compensation increased cement thickness at the loading area by 200 µm in milled 3Y-TZP restorations compared with the 3D-printed partial-coverage crowns. Fracture resistance was the highest in 3D-printed 3Y-TZP restorations (1570±661N) followed by milled 3Y-TZP (886±164N) and 3D-printed composite partial-coverage crowns (570±233 N). Milled 3Y-TZP was associated with a substantially higher Weibull modulus (m=6) than the 3D-printed materials (m=2), suggesting greater reliability.

CONCLUSIONS

Fracture resistance increased with tighter fit, demonstrating the benefit of the geometric freedom associated with 3D-printing. Future research should focus on making 3D-printed 3Y-TZP more reliable to increase its safety in clinical use.

Clinical Outcome of Indirect Bonded Porcelain Restoration Versus Full-Coverage Crown on Endodontically Treated Teeth in Posterior Areas: A Systematic Review

The significant loss of tooth structure that occurs after dental caries and endodontic therapy is a common clinical challenge. Several methods were discussed in the literature to treat badly damaged teeth. This systematic review aims to compare the clinical outcomes of partial indirect bonded porcelain restorations to full-coverage crowns of endodontically treated teeth in posterior areas. The study followed the Preferred Reporting Items for Systematic Reviews and Meta-Analysis (PRISMA) guidelines. Data included in the review were identified through bibliographic research on electronic databases (PubMed/Medline, Google Scholar, Cochrane Library, and Web of Science). The strategy was applied by searching for randomized clinical trials (RCTs), cohort studies, and case-control studies using keywords (partial indirect bonded porcelain restoration, partial indirect bonded restoration, inlay and onlay, full convergent crown, and ceramic crown). As a result of a literature search through selected databases using the keywords, 88,421 papers were identified. A total of 671 articles were related and screened for inclusion and exclusion criteria. Four hundred and eighty-two articles that did not meet the inclusion criteria were excluded. A total of 189 full-text papers were assessed, and 20 articles were included in this study. Nineteen cohort studies and one case-control study were included and assessed in this review. This study concludes that both full-coverage crowns and partial indirect bonded restorations demonstrate comparable survival rates. However, limited studies exist regarding partial indirect bonded restorations on endodontically treated teeth, indicating the need for further updated studies.

Effect of different surface treatments and adhesive cementation on the surface topography and flexural strength of translucent and ultra-translucent monolithic zirconia

PURPOSE

To evaluate the effect of different surface treatments and adhesive cementation on the miniflexural strength (MFS) of monolithic zirconia.

MATERIALS AND METHODS

Two-hundred and forty (240) sintered bars of translucent zirconia (ZT) and ultra-translucent zirconia (ZUT) were obtained (8 mm ×2 mm ×1 mm). The bars were divided into 16 groups (n = 15) according to the factors "Zirconia" (ZT and ZUT), "Cementation" (Cem) and "surface treatment" (Ctrl:Control, Al:Aluminum oxide/Al2O3 50 µm, Si:Silica/SiO2 coated alumina particles oxide 30 µm, Gl:Glazing+hydrofluoric acid). Half of the bars received an adhesive layer application, followed by application of resin cement and light curing. The surface roughness was measured in non-cemented groups. All the bars were subjected to the MFS test (1.0 mm/min; 100 kgf). Scanning electron microscopy was used for qualitative analyses. MFS data (MPa) and roughness (µm) were statistically evaluated by three-way and two-way ANOVA respectively and Tukey's test (5%).

RESULTS

The surface treatment and the interaction were significant for roughness. Glazing promoted less roughness compared to silicatization. Regarding MFS, only the zirconia and surface treatment factors were significant. For ZT, the sandblasted groups had an increase in MFS and glazing reduced it. There was no difference between the groups without cementation for the ZUT; however, ZUT.Si/Cem, and ZUT.Al/Cem obtained superior MFS among the cemented groups.

CONCLUSIONS

Sandblasting increases the flexural strength for ZT, while glaze application tends to reduce it. Applying resin cement increases the flexural strength of ZUT when associated with sandblasting. Sandblasting protocols promote greater surface roughness.

The mechanical complications and behavior of angulated dental implant abutment systems versus conventional abutments, a narrative review

Background

Angulated screw channel (ASC) abutment allows off-axis dental implants to be used in dental restorations without the need for cementation. As this is a relatively new system, research on its clinical performance is limited.

Objectives

To summarize the available in-vitro and in-vivo studies on the mechanical and technical issues associated with the ASC system and compare its clinical performance with that of conventional implant-supported abutments.

Methods

A comprehensive literature search in PubMed, Web of Science, and ScienceDirect databases was performed, focusing on articles about angulated (angled) screw channel (ASC) systems published in English between January 2015 and November 2023. Only in-vitro and in-vivo studies were included.

Results

After analyzing the recorded articles, 26 studies (11 in vivo and 15 in vitro) were included in the final discussion and review.

Conclusion

Although the ASC system is still relatively new, and is presently outperformed by conventional abutment systems in terms of technical and mechanical properties, in short- and medium-term in-vivo studies, it was shown reliable for retaining single or multiple-unit implant restorations in both posterior and anterior zones. Still, further long-term clinical research is needed to fully elucidate the risk factors associated with ASC failures.

Effects of plasma surface treatment on the bond strength of zirconia with an adhesive resin luting agent

The purpose of this study was to evaluate the effect of the atmospheric pressure plasma treatment as a surface treatment method on the contact angle and shear bond strength (SBS) of zirconia ceramics and the failure mode between the self-adhesive resin luting agent and zirconia. The zirconia specimens were divided into eight groups based on the surface treatment method: alumina blasting, air plasma, argon plasma (AP), Katana cleaner, ozonated water, ozonated water+AP, Katana cleaner+AP, and tap water+AP. The contact angles, SBS, and fracture modes were tested. AP treatment significantly reduced the contact angle (p<0.0001). The combination of AP and other cleaning methods showed a higher bond strength and more mixed fractures. Our findings indicate that using atmospheric pressure plasma with argon gas, combined with other cleaning methods, results in a stronger bond than when using alumina blasting alone.

Zirconia CAD-CAM Crowns Behavior after Intraoral Digital Impression in Normal versus Dysfunctional Patients: 3 Years Retrospective Study

OBJECTIVES

 The aim of this study was to evaluate the clinical performance and possible complications of single zirconia crowns fabricated using an intraoral digital computer-aided design-computer-aided manufacturing (CAD-CAM) protocol in normal and dysfunctional patients after 3 years of follow-up.

MATERIALS AND METHODS

 Seventy patients were included in this study. The teeth were prepared with a knife-edge marginal design, and temporary crowns were placed. Digital impressions were taken using optical scanning, and the frameworks were milled using the same technology. The veneering process was performed by the same dental technician. The occlusal corrections were made before cementation. The outcomes were evaluated in terms of survival, failures, and complications. The marginal adaptation of the crowns was also assessed.

RESULTS

 The digital protocol for single zirconia crowns resulted in satisfactory outcomes, with high rates of survival and minimal complications after 3 years of follow-up. The marginal adaptation of the crowns was excellent, with 93% of the restorations achieving the ideal marginal adaptation, while 7% had minor deviations. Parafunctions were found in 41.9% of the prosthetic rehabilitation, but no significant differences were observed between the normal and dysfunctional groups regarding the survival and complications of the crowns.

CONCLUSION

 The digital protocol for single zirconia crowns is a reliable and predictable treatment option, even for patients with parafunction, when proper occlusal corrections are performed before cementation. The use of intraoral digital CAD-CAM technologies with optical impressions can simplify procedures, reduce the workflow time, and minimize the variables linked to the human factor.

Performance of posterior third-generation monolithic zirconia crowns in a complete digital workflow: A three-year prospective clinical study

Background/purpose

Translucent monolithic zirconia restorations have recently introduced. The purpose of this study was to evaluate the clinical behavior and the survival rate of the posterior third-generation monolithic zirconia crowns (MZCs) during three years of clinical service.

Materials and methods

Twenty-four patients who needed thirty crowns were enrolled in this study. Digital impressions were made, and the crowns were milled and cemented with a resin cement. The crowns outcomes were assessed using the California Dental Association's (CDA) criteria. Gingival index (GI), plaque index (PI), and periodontal probing depth (PPD) for MZCs and contralateral natural teeth (control) were assessed. Margin index (MI) for MZCs was also assessed. Data analysis was conducted using the Wilcoxon signed-rank and the Friedman tests.

Results

The 3-year survival rate was 100%. All MZCs were rated as satisfactory throughout the follow-up period, and no biological or mechanical complications were observed. No differences were recorded when GI, PI and PPD at 3-year of follow-up were compared to baseline. No differences were recorded between crowned and control teeth. The MI remained stable throughout the study period.

Conclusion

The third-generation monolithic zirconia appears to be a good treatment option for the rehabilitation of posterior single teeth.

Effect of low-temperature degradation and sintering protocols on the color of monolithic zirconia crowns with different yttria contents

This study investigated the effects of low-temperature degradation (LTD) on the L*, a*, and b* values of highly translucent zirconia crowns. Four types of zirconia disks with different yttria contents (IPS e.max ZirCAD LT, IPS e.max ZirCAD MT, IPS e.max ZirCAD MT Multi, IPS e.max ZirCAD Prime, Ivoclar) and two shades (A2 and BL) were used. A crown was manufactured using four types of zirconia and LTD treated. Color measurements were performed, and the color difference (ΔE00) before and after LTD was calculated. The microstructure was determined through X-ray fluorescence and X-ray diffractometry. Highly translucent zirconia crowns showed greater changes in the a* and b* values than in the L* value after LTD, regardless of the shade. The Multi2 crowns exhibited a discernible color change due to the LTD treatment. The X-ray fluorescence results did not reveal any apparent change in the microstructure between sintering programs for all zirconia specimens.

Ultrathin lithium disilicate and translucent zirconia crowns for posterior teeth: Survival and failure modes

PURPOSE

To evaluate the reliability and failure modes of ultrathin (0.5 mm) lithium disilicate, translucent and ultra-translucent zirconia crowns for posterior teeth restorations.

MATERIALS AND METHODS

Fifty-four mandibular first molar crowns of three ceramic materials: (1) Lithium disilicate (e.max CAD, Ivoclar Vivadent), (2) 3Y-TZP (Zirconn Translucent, Vipi), and (3) 5Y-PSZ (Cercon XT, Dentsply Sirona), with 0.5 mm of thickness were milled and cemented onto composite resin abutments. Eighteen samples of each group were tested under mouth-motion step-stress accelerated life testing in a humid environment using mild, moderate, and aggressive profiles. Data was subjected to Weibull statistics. Use level curves were plotted and reliability was calculated for a given mission of 100,000 cycles at 100, 200, and 300 N. Fractographic analyses of representative samples were performed in scanning electron microscope.

RESULTS

Beta (β) values suggest that failures were dictated by material's strength for lithium disilicate and by fatigue damage accumulation for both zirconias. No significant differences were detected in Weibull modulus and characteristic strength among groups. At a given mission of 100,000 cycles at 100 N, lithium disilicate presented higher reliability (98% CB: 95-99) regarding 3Y-TZP and 5Y-PSZ groups (84% CB: 65%-93% and 79% CB: 37&-94%, respectively). At 200 N, lithium disilicate reliability (82% CB: 66%-91%) was higher than 5Y-PSZ (20% CB: 4%-44%) and not significantly different from 3Y-TZP (54% CB: 32%-72%). Furthermore, at 300 N no significant differences in reliability were detected among groups, with a notable reduction in the reliability of all materials. Fractographic analyses showed that crack initiated at the interface between the composite core and the ceramic crowns due to tensile stress generated at the intaglio surface.

CONCLUSIONS

Ultrathin lithium disilicate crowns demonstrated higher reliability relative to zirconia crowns at functional loads. Lithium disilicate and zirconia crown's reliability decreased significantly for missions at higher loads and similar failure modes were observed regardless of crown material. The indication of 0.5 mm thickness crowns in high-load bearing regions must be carefully evaluated.

CLINICAL SIGNIFICANCE

Ultraconservative lithium disilicate and zirconia crowns of 0.5 mm thickness may be indicated in anterior restorations and pre-molars. Their clinical indication in high-load requirement regions must be carefully evaluated.

Digital workflow for monolithic and veneered zirconia and metal-ceramic posterior fixed partial dentures: A five-year prospective randomized clinical trial

Purpose To evaluate and compare the survival, success rates, and biological and technical complications of three-unit posterior monolithic and veneered zirconia and metal-ceramic (MC) posterior fixed partial dentures (FPDs) fabricated using a digital workflow and computer-aided design and computer-aided manufacturing (CAD/CAM) over a 5-year follow-up.Methods Ninety patients in need of three-unit posterior FPDs were randomized to receive monolithic zirconia (MZ), veneered zirconia (VZ), and MC restorations (n = 30 each). Teeth preparations were scanned using an intraoral scanner, and restorations were milled and cemented with resin cement. Clinical performance and periodontal parameters were assessed at baseline and yearly up to 5 years after insertion. Data analysis was performed using the Kaplan-Meier method, Friedman test, and Wilcoxon signed-rank test with Bonferroni correction and Mann-Whitney U test.Results The 5-year survival rates of the MZ, VZ, and MC FPDs were 87%, 97%, and 100%, respectively (P = 0.04). Most complications were biological in nature. Only one MZ FPD fractured 58 months after placement. All the restorations were assessed as satisfactory at each recall. Differences were found in the gingival index score over time in the VZ and MC groups. The margin index remained stable throughout the follow-up period in both zirconia groups.Conclusions The results of this study suggest that using a digital workflow to fabricate posterior FPDs is an adequate treatment option and that monolithic zirconia could be a viable alternative to metal-ceramic or veneered zirconia. However, further long-term studies are necessary to provide stronger evidence in patients with bruxism.

The effect of low-temperature degradation and building directions on the mechanical properties of additive-manufactured zirconia

This study aimed to investigate the effect of low-temperature degradation (LTD) on the mechanical properties of additive-manufactured zirconia. In addition, the mechanical properties of additive-manufactured were compared with those before aging under similar experimental conditions. This study prepared stereolithography apparatus fabricated zirconia specimens with flexural strength, modulus of elasticity, Vickers hardness, and fracture toughness. The specimen position data were set as parallel (0°), diagonal (45°), and perpendicular (90°) to the direction of the building. The LTD condition was 5 h under 134ºC and 0.2 MPa in an autoclave. It was found that the 0° direction differed significantly from all other conditions before and after aging, and the highest flexural strength was obtained when the additive specimen was manufactured perpendicular to the building direction. However, the results indicate that there is a negligible effect of aging on the mechanical properties of additive-manufactured zirconia.

Translucent Zirconia in Fixed Prosthodontics-An Integrative Overview

Over the past two decades, dental ceramics have experienced rapid advances in science and technology, becoming the fastest-growing field of dental materials. This review emphasizes the significant impact of translucent zirconia in fixed prosthodontics, merging aesthetics with strength, and highlights its versatility from single crowns to complex bridgework facilitated by digital manufacturing advancements. The unique light-conducting properties of translucent zirconia offer a natural dental appearance, though with considerations regarding strength trade-offs compared to its traditional, opaque counterpart. The analysis extends to the mechanical attributes of the material, noting its commendable fracture resistance and durability, even under simulated physiological conditions. Various zirconia types (3Y-TZP, 4Y-TZP, 5Y-TZP) display a range of strengths influenced by factors like yttria content and manufacturing processes. The study also explores adhesive strategies, underlining the importance of surface treatments and modern adhesives in achieving long-lasting bonds. In the realm of implant-supported restorations, translucent zirconia stands out for its precision, reliability, and aesthetic adaptability, proving suitable for comprehensive dental restorations. Despite its established benefits, the review calls for ongoing research to further refine the material's properties and adhesive protocols and to solidify its applicability through long-term clinical evaluations, ensuring its sustainable future in dental restorative applications.

Clinical outcomes of tooth-supported monolithic zirconia vs. porcelain-veneered zirconia fixed dental prosthesis, with an additional focus on the cement type: a systematic review and meta-analysis

PURPOSE

To compare the failure rates and the prevalence of technical complications between full-coverage tooth-supported monolithic zirconia (MZ) and porcelain-veneered zirconia (PVZ) fixed dental prosthesis, based on a systematic literature review.

METHODS

An electronic search was performed in three databases, supplemented by hand searching. Several statistical methods were used.

RESULTS

Seventy-four publications reported 6370 restorations (4264 PVZ; 2106 MZ; 8200 abutment teeth; 3549 patients), followed up until 152 months. A total of 216 prostheses failed, and survival was statistically significant different between groups. PVZ had higher occurrence of complications than MZ; the difference was especially greater for either minor or major chipping. The difference in prevalence of either minor or major chipping was statistically significant for PVZ prostheses between cementation with glass ionomer and adhesive resin cement (higher), adhesive resin and resin-modified glass ionomer cement (RMGIC, higher), and between RMGIC (higher) and glass ionomer cement. For MZ the difference was significant only for minor chipping between RMGIC (higher) and adhesive resin cement. Abutment teeth to PVZ prostheses more often lost vitality. Decementation was not observed with RMGIC. Air abrasion did not seem to clinically decrease the decementation risk. The 5-year difference in the occurrence of minor or major chipping between MZ and PVZ prostheses was statistically significant, but nor for catastrophic fracture.

CONCLUSION

Tooth-supported PVZ prostheses present higher failure and complication rates than MZ prosthesis. The difference in complications is striking when it comes to chipping.

CLINICAL RELEVANCE

Awareness of the outcome differences between different types of zirconia prostheses is important for clinical practice.

Speed-sintering and the mechanical properties of 3-5 mol% Y2O3-stabilized zirconias

Ever faster workflows for the fabrication of all-ceramic restorations are of high economic interest. For that purpose, sintering protocols have been optimized for use in modern sintering furnaces, the so-called speed-sintering. However, conventional furnaces are still the most widely used equipment to sinter zirconia restorations. In this in-vitro study, we evaluated the feasibility of a speed-sintering protocol using a conventional sintering furnace to sinter different dental zirconias (stabilized with 3 mol% up to 5.4 mol% Y2O3) in comparison to a conventional sintering program. The properties evaluated were Young's modulus, Poisson's ratio, density, biaxial flexural strength, and fracture toughness. We show here that despite differences being dependent on material, the physical and mechanical properties of speed-sintered zirconia are comparable to those obtained by the conventional sintering.

Mechanical and surface properties of additive manufactured zirconia under the different building directions

PURPOSE

This study investigates the mechanical and surface properties of zirconia manufactured using additive manufacturing (AM) technology and the effect of the building direction on the mechanical and surface properties.

METHODS

Specimens were prepared using ZrO₂ paste (3DMix ZrO₂; 3DCeram) and a three-dimensional printing system (CeraMaker 900; 3DCeram) based on the principles of stereolithography (SLA). The mechanical properties (flexural strength, Vickers hardness, fracture toughness, elastic modulus, and Poisson's ratio) and surface properties (chemical composition and surface observation) were evaluated for three building directions (parallel, diagonal, and perpendicular) to investigate the relationship between the building directions and the anisotropy of the mechanical and surface properties of SLA-manufactured zirconia. Statistical analysis was performed using a one-way analysis of variance and Tukey's honestly significant difference test.

RESULTS

The highest flexural strength was obtained for a perpendicular building direction. The flexural strength was significantly higher in the perpendicular direction than in the parallel and diagonal directions; it was also significantly higher in the diagonal direction than in the parallel direction (P<0.05). The Vickers hardness, fracture toughness, elastic modulus, Poisson's ratio, and chemical composition did not differ significantly. Microstructural observations revealed that the layers, large crystals, and pores were more prominent in the parallel direction.

CONCLUSIONS

The flexural strength and surface structure of the tested SLA-manufactured zirconia were influenced by the building direction; however, other mechanical properties remained unaffected. The layer boundaries affected the anisotropic behavior of the builds to a certain extent, owing to the layer-by-layer production method.

Clinical Outcomes of Monolithic Zirconia Crowns on Posterior Natural Abutments Performed by Final Year Dental Medicine Students: A Prospective Study with a 5-Year Follow-Up

The conventional metal-ceramic is still considered the gold standard in fixed prosthetics especially in terms of longevity. Among alternative materials used, Monolithic Zirconia has shown the capability to reconcile excellent biomechanical properties with acceptable aesthetic performance and to overcome several inconveniences related to veneer restorations. This study aims to clinically evaluate Monolithic Zirconia prosthetic crowns on natural abutments in the posterior sectors, performed by final-year dental medicine students (undoubtedly with less experience in the management of such material) by the standardized California Dental Association score system evaluation, to better understand the viability of Monolithic Zirconia. This prospective study was carried out at the Dental School of the University of Bari "Aldo Moro", Italy. Prosthetic rehabilitation included single crowns or a short pontic prosthesis with maximum one intermediate. Final-year dental students performed tooth reduction under the supervision of three expert tutors. The California Dental Association systematics (based on color, surface, anatomical shape, and marginal integrity) were adopted to evaluate the prosthetic maintenance status over time. Annual follow-up visits were re-evaluated by the same parameters each year. Univariate logistic regression analysis was performed to evaluate outcomes and the Kaplan-Meier plot to report survival. The sample consists of 40 crowns performed on 31 patients, 15 males (48.4%) and 16 females (51.6%) with an average age of 59.3 years. The clinical cases subjected to experimental study were found to be "Excellent" (1a/2a/3a/4a) in 34 cases (85%), "Acceptable" in 4 cases (10%), and "To be re-done" in 2 cases (failures) (5%). Our conclusive data support the predictability of Monolithic Zirconia restorations on natural posterior abutments at a long-term follow-up of five years, even when performed by less-experienced clinicians.

Effect of speed sintering of monolithic zirconia with different yttria contents on color and crystal phase

This study evaluated the color and microstructure of monolithic zirconia crowns with different yttrium oxide (Y₂ O₃ ) contents treated by conventional or speed sintering. Four types of zirconia ceramics were assessed: two monolayer zirconia, and two multilayer zirconia. The monolithic zirconia crowns were fabricated using a dental computer-aided design/computer-aided manufacturing (CAD/CAM) system and in two shades (A2 and BL). After milling, the zirconia crowns were sintered using either speed sintering or conventional sintering. For each combination of zirconia (4), shade (2), and sintering condition (2), the color parameters were determined at three positions of each of nine crowns using a non-contact dental spectrophotometer. In addition, the zirconia phases in the specimens were quantified using X-ray diffractometry. Significant differences in the ΔE₀₀ values at different measurement positions were observed for the Multi2 crown of the BL shade group. The color difference resulting from conventional and speed sintering programs was not affected by the difference in yttria content of Mono1, Mono2, and Multi1. However, in Multi2, containing 3Y-TZP and 5Y-PSZ, a color change was caused by the use of speed sintering. Therefore, when performing speed sintering with Multi2, it is necessary to select the color in consideration of these results or take measures for staining.

The 3-year cumulative survival rates of posterior monolithic zirconia crowns and their antagonist teeth, and their influencing factors

PURPOSE

The purpose of this study was to evaluate the 3-year cumulative survival rates of posterior single monolithic zirconia crowns (MZCs) and their antagonists, and to analyze the influencing factors.

METHODS

The clinical outcomes of posterior single MZCs and their abutment teeth with antagonists, and the antagonists between April 2014 and September 2020 were evaluated retrospectively. The 3-year cumulative survival rates were calculated and associations between the survival time and predictor variables ("Jaw", "Tooth", and "Pulpal condition") were also verified using Cox proportional hazards models and hazard ratios (HRs).

RESULTS

The 3-year cumulative survival rate of single MZCs was 89.8% (9 of 177 MZCs, 95% confidence interval (CI): 80.0-95.1%). Cox proportional hazards models showed non-vital teeth were significantly associated with failure (HR: 2.76e + 9, P = 0.012). The 3-year cumulative survival rate of antagonists was 94.8% (7 of 171 antagonists, 95% CI: 89.3-97.6%). Non-vital antagonists were also identified as an independent predictor for failure in Cox proportional hazards models (HR: 7.83, P = 0.03).

CONCLUSION

Although posterior single MZCs were clinically acceptable, non-vital pulpal condition could be a potential risk factor for failures in the abutment and antagonist teeth of MZCs.

Comparative Assessment of the Functional Parameters for Metal-Ceramic and All-Ceramic Teeth Restorations in Prosthetic Dentistry-A Literature Review

Simple Summary

In the last decades, the science and technology of all-ceramic teeth restorations witnessed the fastest-growing field of restorative materials in research and development for fixed prosthodontics. Due to their properties, characterized by a high level of biocompatibility, excellent optical properties, and high fracture resistance, all-ceramic material can also be used in the posterior areas of the dental arches. However, metal-ceramic fixed partial dentures are still perceived as the golden standard for those restorations, thanks to the positive clinical outcomes. Irrespective of the materials of which fixed partial dentures are performed, their success rates depend on the expected outcome and on how they perform in the oral environment. Such conditions of failure restorations may include biological factors (i.e., secondary decay, loss of vitality, periodontal disease, or abutment fracture) or technical factors (i.e., chipping, ceramic fracture, framework fracture, or loss of retention). Our aim is to provide the current evidence for the efficacy of metal-ceramics and all-ceramics in the treatment of multiple posterior edentulous spaces. Moreover, we aim to compare the survival rates of metal-ceramic and all-ceramic fixed partial dentures in terms of functionality and biocompatibility in all the aforementioned clinical situations. Our results have shown that all all-ceramic systems, especially densely sintered zirconia and reinforced glass ceramics, have a promising future to satisfy both practitioners and patients. However, technical and biological complications need to be taken into account when planning multi-unit fixed partial dentures for the posterior areas.

Abstract

The metal-ceramic fixed partial prosthesis is the golden standard for posterior tooth restorations. Following the demands of patients and clinicians for metal-free restorations, all-ceramic materials were developed as they offer an adequate alternative with better optical qualities and good mechanical properties. This study aims to carry out a bibliographic review to assess the survival rate and the biological and technical complications of all-ceramic and metal-ceramic fixed partial dentures. An electronic search for articles in the English language literature was performed using PubMed (MEDLINE). This literature review focused on research studies between 2010 and 2020 that performed clinical studies on tooth-supported fixed partial dentures with a mean follow-up of at least 3 years. All the studies, which analyzed the survival and complications of tooth-supported fixed partial dentures, were included. Thus, 14 studies reporting on 756 all-ceramic and 160 metal-ceramic fixed partial dentures met the inclusion criteria. A comparative analysis was carried out based on all the data existing in the studies included in this review. The metal-ceramic fixed partial dentures showed survival rates of 95% to 100% at 3-, 5-, and 10-year follow-up periods. Zirconia fixed partial dentures were reported to have survival rates of 81% to 100% at 3-, 5-, 9-, 10-year follow-up evaluations. The reinforced glass-ceramic fixed partial dentures showed survival rates of 70% to 93.35% at 5 years, while the alumina FPDs showed a survival rate of 68% at 3 years follow-up. The incidence of caries and loss of vitality were reported as higher for all-ceramic prostheses as compared to the metal-ceramic ones. A significant framework fracture was reported for glass-infiltrated alumina fixed partial dentures in comparison to metal-ceramic fixed partial dentures. All-ceramic and metal-ceramic restorations showed similar survival rates after 3 years, although all-ceramic restorations have problems with technical complications such as chipping, which can lead to framework fractures over time.

Comparison of stress distribution between zirconia/alloy endocrown and CAD/CAM multi-piece zirconia post-crown: three-dimensional finite element analysis

OBJECTIVES

This study aimed to evaluate a digital multi-piece zirconia post-crown to restore a mandibular second molar with extensive coronal loss and limited restoration space, and to compare the stress distribution between endocrowns made of zirconia or alloy and CAD/CAM multi-piece zirconia post-crowns.

MATERIAL AND METHODS

Four three-dimensional finite element analysis models of a mandibular second molar with extensive coronal loss and limited restoration space were created as follows: (A) intact molar; (B) zirconia endocrown restored molar; (C) multi-piece post-crown restored-molar with tapered nail; (D) multi-piece post-crown restored molar with T-shaped nail. Models C and D were divided into two subgroups according to the material type: C1/D1, zirconia; C2/D2, NiCr alloy. The maximum modified von Mises failure criterion (mvM) stresses were calculated, and the stress distribution was recorded to analyze the effects of the restoration and material types on the biomechanical properties of dentin and prosthesis.

RESULTS

The maximum mvM stress of dentin in model B (33.80 MPa) was lower compared with models C (C1, 37.81 MPa; C2, 36.36 MPa) and D (D1, 36.34 MPa; D2, 34.97 MPa) under vertical load, but the opposite was observed under oblique load. The highest mvM stress was concentrated in the nail region located in the root canal, and the T-shaped nail values were greater than the tapered nail, whereas model D with T-shaped nail showed a lower mvM stress level in dentin compared with Model C with tapered nail.

CONCLUSIONS

The digital multi-piece zirconia post-crown is a potential approach to restore mandibular second molars with extensive coronal loss and limited restoration space.

CLINICAL RELEVANCE

The digital multi-piece zirconia post-crown has potential to restore mandibular second molars with extensive coronal loss and limited restoration space using an innovative approach.

FRACTOGRAPHIC ANALYSIS OF LITHIUM DISILICATE CERAMICS AND MONOLITHIC ZIRCONIA CERAMICS

Objective: To compare the fracture mode of lithium disilicate ceramics and zirconia ceramics through a single-load-to-failure test, and reveal the cause of failure through the fractographic analysis of fracture morphology. Methods: Based on the standardized preparations, 10 IPS e.max disilicate ceramic crowns (IPCs) and 10 monolithic zirconia ceramic crowns (MZCs) were designed and fabricated. All the specimens were placed on a universal material testing machine for a single-load-to-failure test. The fracture load was recorded, and two independent sample [Formula: see text]-tests were performed. Additionally, the type of fracture under a stereo-microscope was observed, and the morphological characteristics of the fracture with a scanning electron microscope (SEM) were investigated. Results: The fracture load of the IPC group was [Formula: see text][Formula: see text]N, and that of the MZC group was [Formula: see text][Formula: see text]N, with a statistically significant difference ([Formula: see text], [Formula: see text]). The fracture types of the IPC group and the MZC group were similar, namely, types II and III. The fracture modes of the two groups were all ceramic layer fracture. Through SEM, the origin of the crack on the occlusal surface could be traced back. The crystal fracture of IPC group had a rock sugar-like pattern, and the crystal distribution of MZC group was uniform. Conclusions: Zirconia ceramics have higher fracture load and a denser crystal structure compared to lithium disilicate. Fractographic analysis method could be a better way to analyze the failure mode of single-layer porcelain materials and reveal the origin of fracture.

Spectrometric Analysis of the Wear from Metallic and Ceramic Dental Implants following Insertion: An In Vitro Study

Titanium wear is a growing area of interest within dental implantology. This study aimed to investigate titanium and zirconium wear from dental implants at the time of insertion using X-ray-fluorescence spectrometry (XRF) and an in vitro protocol utilizing artificial bovine bone plates. Five groups were analyzed using XRF-spectrometry: groups 1–4 (titanium implants) and group 5 (zirconia implants). The implants were inserted into two bone blocks held together by a vice. The blocks were separated, and the insertion sites were analyzed for titanium (Ti) and zirconium (Zr). Statistical descriptive analyses of Ti and Zr concentrations in the coronal, middle and apical bone interface were performed. A comparative analysis confirmed differences between the implant’s surface stability and Ti accumulation within the insertion sites of the bone block. There was a direct relationship between implant length and the quantity of titanium found on the bone block. The data generally indicates greater quantities of titanium in the coronal thirds of the implants, and less in the apical thirds. The titanium and zirconium found in the bone samples where the group 5 implants were inserted was not of statistical significance when compared to control osteotomies. The results of this study confirm wear from metallic, but not ceramic, dental implants at the time of insertion.

Prospective Clinical Evaluation of Posterior Third-Generation Monolithic Zirconia Crowns Fabricated with Complete Digital Workflow: Two-Year Follow-Up

Clinical studies on the behavior of posterior translucent monolithic zirconia restorations are lacking. We assessed the clinical outcome and survival rate of posterior third-generation monolithic zirconia crowns over a 2-year period. A total of 24 patients, requiring 30 posterior full-contour restorations were selected. All abutments were scanned, and crowns were milled and cemented with a self-adhesive dual cure cement. Crowns were assessed using the California Dental Association’s criteria. Gingival status was assessed by evaluating the gingival index, plaque index, periodontal probing depth of the abutments and control teeth, and the margin index of the abutment teeth. Statistical analyses were performed using the Friedman and the Wilcoxon signed-rank tests. During the 2-year follow-up, no biological or mechanical complications were observed, and the survival and success rate was 100%. All restorations ranked as satisfactory throughout the follow-up period. The gingival index and plaque index were worse at the end of the 2-year follow-up. The margin index was stable during the 2 years of clinical service. No significant differences were recorded in periodontal parameters between crowns and control teeth. Third-generation monolithic zirconia could be a reliable alternative to posterior metal–ceramic and second-generation monolithic zirconia posterior crowns.

Monolithic zirconia crowns: effect of thickness reduction on fatigue behavior and failure load

PURPOSE

The objective of this study was to evaluate the effect of thickness reduction and fatigue on the failure load of monolithic zirconia crowns.

MATERIALS AND METHODS

140 CAD-CAM fabricated crowns (3Y-TZP, inCorisTZI, Dentsply-Sirona) with different ceramic thicknesses (2.0, 1.5, 1.0, 0.8, 0.5 mm, respectively, named G2, G1.5, G1, G0.8, and G0.5) were investigated. Dies of a mandibular first molar were made of composite resin. The zirconia crowns were luted with a resin composite cement (RelyX Unicem 2 Automix, 3M ESPE). Half of the specimens (n = 14 per group) were mouth-motion-fatigued (1.2 million cycles, 1.6 Hz, 200 N/ 5 – 55℃, groups named G2-F, G1.5-F, G1-F, G0.8-F, and G0.5-F). Single-load to failure was performed using a universal testing-machine. Fracture modes were analyzed. Data were statistically analyzed using a Weibull 2-parameter distribution (90% CI) to determine the characteristic strength and Weibull modulus differences among the groups.

RESULTS

Three crowns (21%) of G0.8 and five crowns (36%) of G0.5 showed cracks after fatigue. Characteristic strength was the highest for G2, followed by G1.5. Intermediate values were observed for G1 and G1-F, followed by significantly lower values for G0.8, G0.8-F, and G0.5, and the lowest for G0.5-F. Weibull modulus was the lowest for G0.8, intermediate for G0.8-F and G0.5, and significantly higher for the remaining groups. Fatigue only affected G0.5-F.

CONCLUSION

Reduced crown thickness lead to reduced characteristic strength, even under failure loads that exceed physiological chewing forces. Fatigue significantly reduced the failure load of 0.5 mm monolithic 3Y-TZP crowns.

Five-year clinical performance of monolithic and partially veneered zirconia single crowns-a prospective observational study

PURPOSE

The purpose of this study was to prospectively evaluate the medium-term clinical performance and esthetics of monolithic and partially (i.e., facially) veneered zirconia single crowns (MZ-SC and PZ-SC, respectively).

METHODS

Between September 2011 and June 2013, 68 participants received 90 MZ-SC and 72 PZ-SC. Clinical study documentation was performed at crown cementation (baseline), at 6-month follow-up, and then yearly thereafter using standardized report forms. Three participants with four MZ-SC dropped out during clinical follow-up. Thus, 65 participants (n = 31, 47.7% men) fitted with 158 restorations (86 MZ-SC, 72 PZ-SC) were evaluated. The mean observation period of the restorations was 5.8 ±2.5 years; 6.3 ±2.2 for MZ-SC and 5.2 ±2.6 for PZ-SC.

RESULTS

The 5-year rate of complication-free survival (success) was 87.0% for MZ-SC and 95.8% for PZ-SC (log-rank test, p = 0.026). The 5-year failure-free survival rate was 93.1% for MZ-SC and 96.2% for PZ-SC (log-rank test, p = 0.111), and the 5-year ceramic fracture-free survival rate was 100% for MZ-SC and 98.6% for PZ-SC (log-rank test, p = 0.274). Crowns of both designs were awarded excellent scores for esthetics by participants and dentists.

CONCLUSIONS

Monolithic and partially veneered zirconia crowns can be used clinically with high medium-term survival and success and uncompromised esthetic results.

Effects of abutment tooth and luting agent colors on final color of high-translucent zirconia crowns

PURPOSE

This study aimed to evaluate the effects of the tooth portion evaluated and the colors of the abutment tooth and resin luting agent on the final color of monolithic zirconia crowns.

METHODS

Monolithic zirconia crowns were fabricated for left maxillary central incisors using two shades (A2 and A3) of highly translucent monolithic zirconia disks. A model of the abutment tooth was fabricated using resin core materials (white: W; dentin: D). The color of the crowns was measured with try-in pastes (clear: C; brown: B) as a resin-luting agent substitute. The measurement was performed after placing the crown on the model with the attached abutment tooth with try-in paste. The color of three labial portions (cervical, body, and incisal) was evaluated using a dental spectrophotometer. The color difference (ΔE) between the CIELab values of the zirconia disks and the final me asurement of zirconia crowns was calculated.

RESULTS

The ΔE between the crown of the A2 shade and the zirconia disk of the A2 shade had the highest ΔE value in the body portion with W-B (ΔE=3.92). Similarly, the A3 shade had the highest ΔE value in the cervical portion, with W-B (ΔE=4.27). The results of three-way ANOVA showed that the ΔE values were influenced by the tooth portion evaluated and the color of the abutment tooth.

CONCLUSIONS

The final color of the monolithic zirconia crowns was significantly in fluenced by the tooth portion evaluated and the color of the abutment tooth.