1
|
Tahamtan S, Hajihosseini M, Sohrabi A. Comparison of alignment efficiency of different sizes of superelastic nickel-titanium archwires in the initial phase of fixed orthodontic treatment: A single-center, double-blind randomized clinical trial. Am J Orthod Dentofacial Orthop 2024; 166:104-111. [PMID: 38775764 DOI: 10.1016/j.ajodo.2024.04.003] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/01/2023] [Revised: 04/01/2024] [Accepted: 04/01/2024] [Indexed: 08/02/2024]
Abstract
INTRODUCTION This 3-arm parallel, double-blind study aimed to evaluate the alignment efficiency of 3 different diameters of superelastic nickel-titanium (NiTi) archwires during the initial phase of orthodontic treatment. METHODS Ninety-three patients with nonextraction treatment in the mandibular arch (using 0.022-in Roth prescription brackets) were randomly allocated into 3 groups: 0.012-in NiTi (group 1), 0.014-in NiTi (group 2), and 0.016-in NiTi (group 3). The alignment change was measured using the modified Little's irregularity index before archwire placement and every 4 weeks. The alignment efficiency of the 3 groups was analyzed. RESULTS Ninety patients were analyzed (group 1: n = 29, group 2: n = 31, and group 3: n = 30; overall mean age, 16.6 years). The overall Wald test analysis revealed that wire type was not statistically significant (P = 0.91), whereas time exhibited significance as expected (P <0.001). Furthermore, the interaction between wire type and time was not significant (P = 0.93). The time-adjusted estimated difference between 0.014-in and 0.012-in was -0.49 (95% confidence interval, -2.83 to 1.85; P = 0.68). The time-adjusted estimated difference between 0.016-in and 0.012-in was -0.45 (95% confidence interval, -2.95 to 2.05; P = 0.72). No harm was observed. CONCLUSIONS The clinical performance of 3 different sizes of NiTi archwires was similar. In addition, 0.014-in and 0.016-in NiTi archwires demonstrated better performances in aligning any irregularities because of a greater number of wire deformations in the 0.012-in group. REGISTRATION IR.TBZMED.REC.1395.1039. PROTOCOL The protocol was not published before trial commencement. FUNDING None.
Collapse
Affiliation(s)
- Shabnam Tahamtan
- Department of Orthodontics, Dental Research Center, Dental Research Institute, School of Dentistry, Isfahan University of Medical Sciences, Isfahan, Iran
| | | | - Aydin Sohrabi
- Department of Orthodontics, Faculty of Dentistry, Tabriz University of Medical Sciences, Tabriz, Iran.
| |
Collapse
|
2
|
Liu C, Wei Z, Jian F, McIntyre G, Millett DT, Lai W, Wang Y. Initial arch wires used in orthodontic treatment with fixed appliances. Cochrane Database Syst Rev 2024; 2:CD007859. [PMID: 38319008 PMCID: PMC10845215 DOI: 10.1002/14651858.cd007859.pub5] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 02/07/2024]
Abstract
BACKGROUND Initial arch wires are the first arch wires inserted into fixed appliance at the beginning of orthodontic treatment. With a number of different types of orthodontic arch wires available for initial tooth alignment, it is important to understand which are most efficient and which cause the least amount of root resorption and pain during the initial aligning stage of treatment. This is the third update of a Cochrane review first published in 2010. OBJECTIVES To assess the effects of initial arch wires for the alignment of teeth with fixed orthodontic braces, in terms of the rate of tooth alignment, amount of root resorption accompanying tooth movement, and intensity of pain experienced by patients during the initial alignment stage of treatment. SEARCH METHODS We searched Cochrane Oral Health's Trials Register, CENTRAL, MEDLINE, Embase, and two ongoing trials registries on 4 July 2022. SELECTION CRITERIA We included randomised controlled trials (RCTs) of different initial arch wires used to align teeth with fixed orthodontic braces. We included people with full-arch fixed orthodontic appliances on the upper arch, lower arch, or both arches. DATA COLLECTION AND ANALYSIS Two independent review authors were responsible for study selection, data extraction, and assessment of risk of bias in included studies. We contacted corresponding authors of included studies to obtain missing information. We resolved disagreements by discussion between the review authors. Our main outcomes were alignment rate (movement of teeth in mm), root resorption, time to alignment, and intensity of pain measured on a 100-mm visual analogue scale (VAS). We pooled data from studies with similar interventions and outcomes using random-effects models. We reported mean differences (MDs) with 95% confidence intervals (CIs) for continuous data, risk ratios (RRs) with 95% CIs for dichotomous data, and alignment rate ratios with 95% CIs for time-to-event data. Two independent review authors assessed the certainty of evidence. We resolved disagreements by discussion between the review authors. MAIN RESULTS We included 29 RCTs with 1915 participants (2581 arches) in this review. Studies were generally small (sample sizes ranged from 14 to 200 participants). Duration of follow-up varied between three days and six months. Eleven studies received funding, six received no funding, and 12 provided no information about funding sources. We judged eight studies at high risk of bias, nine at low risk, and 12 at unclear risk. We grouped the studies into six main comparisons. Multistrand stainless steel wires versus wires composed of other materials Six studies with 409 participants (545 arches) evaluated multistrand stainless steel (StSt) wires versus wires composed of other materials. We are very uncertain about the effect of multistrand StSt wires versus other wires on alignment rate (4 studies, 281 participants, 417 arches; very low-certainty evidence). There may be little to no difference between multistrand StSt wires and other wires in terms of intensity of pain (MD -2.68 mm, 95% CI -6.75 to 1.38; 2 studies, 127 participants, 127 arches; low-certainty evidence). Conventional nickel-titanium wires versus superelastic nickel-titanium wires Four studies with 266 participants (274 arches) evaluated conventional nickel-titanium (NiTi) wires versus superelastic NiTi wires. There may be little to no difference between the different wire types in terms of alignment rate (124 participants, 124 arches, 2 studies; low-certainty evidence) and intensity of pain (MD -0.29 mm, 95% CI -1.10 to 0.52; 2 studies, 142 participants, 150 arches; low-certainty evidence). Conventional nickel-titanium wires versus thermoelastic copper-nickel-titanium wires Three studies with 210 participants (210 arches) evaluated conventional Ni-Ti versus thermoelastic copper-nickel-titanium (CuNiTi) wires. We are very uncertain about the effects of the different arch wires on alignment rate (1 study, 66 participants, 66 arches; very low-certainty evidence). There may be little to no difference between conventional NiTi wires and thermoelastic CuNiTi wires in terms of time to alignment (alignment rate ratio 1.30, 95% CI 0.68 to 2.50; 1 study, 60 participants, 60 arches; low-certainty evidence). Superelastic nickel-titanium wires versus thermoelastic nickel-titanium wires Twelve studies with 703 participants (936 arches) evaluated superelastic NiTi versus thermoelastic NiTi wires. There may be little to no difference between superelastic NiTi wires and thermoelastic NiTi wires in alignment rate at four weeks (MD -0.28 mm, 95% CI 0.62 to 0.06; 5 studies, 183 participants, 183 arches; low-certainty evidence). We are very uncertain about the effects of the different wires on root resorption (2 studies, 52 participants, 312 teeth; very low-certainty evidence). Superelastic NiTi wires compared with thermoelastic NiTi wires may result in a slight increase in time to alignment (MD 0.5 months, 95% CI 0.21 to 0.79; 1 study, 32 participants, 32 arches; low-certainty evidence) but are probably associated with a slight increase in intensity of pain (MD 6.96 mm, 95% CI 1.82 to 12.10; 3 studies, 94 participants, 138 arches, moderate-certainty evidence). Single-strand superelastic nickel-titanium wires versus coaxial superelastic nickel-titanium wires Three studies with 104 participants (104 arches) evaluated single-strand superelastic NiTi versus coaxial superelastic NiTi wires. Use of single-strand superelastic NiTi wires compared with coaxial superelastic NiTi wires probably results in a slight reduction in alignment rate at four weeks (MD -2.64 mm, 95% CI -4.61 to -0.67; 2 studies, 64 participants, 64 arches, moderate-certainty evidence). Different sizes of nickel-titanium wires Two studies with 149 participants (232 arches) compared different types of NiTi wires. There may be little to no difference between different sizes of NiTi wires in terms of pain (low-certainty evidence). AUTHORS' CONCLUSIONS Superelastic NiTi wires probably produce slightly more pain after one day than thermoelastic NiTi wires, and single-strand superelastic NiTi wires probably have a lower alignment rate over four weeks compared with coaxial superelastic NiTi wires. All other evidence on alignment rate, root resorption, time to alignment, and pain is of low or very low certainty in all comparisons. Therefore, there is insufficient evidence to determine whether any particular arch wire material or size is superior to any other. The findings of this review are imprecise and unreliable; well-designed larger studies are needed to give better estimates of the benefits and harms of different arch wires. Orthodontists should exercise caution when interpreting the findings of this review and be prepared to adapt their treatment plans based on individual patient needs.
Collapse
Affiliation(s)
- Chang Liu
- State Key Laboratory of Oral Diseases, National Center for Stomatology, National Clinical Research Center for Oral Diseases, Department of Oral and Maxillofacial Surgery, Department of Information Management (Department of Dental Informatics), Department of Evidence-Based Dentistry, West China Hospital of Stomatology, Sichuan University, Chengdu, China
| | - Zhi Wei
- State Key Laboratory of Oral Diseases, National Center for Stomatology, National Clinical Research Center for Oral Diseases, Department of Orthodontics, West China Hospital of Stomatology, Sichuan University, Chengdu, China
| | - Fan Jian
- State Key Laboratory of Oral Diseases, National Center for Stomatology, National Clinical Research Center for Oral Diseases, Department of Orthodontics, West China Hospital of Stomatology, Sichuan University, Chengdu, China
| | | | - Declan T Millett
- Oral Health and Development, Cork University Dental School and Hospital, Cork, Ireland
| | - Wenli Lai
- State Key Laboratory of Oral Diseases, National Center for Stomatology, National Clinical Research Center for Oral Diseases, Department of Orthodontics, West China Hospital of Stomatology, Sichuan University, Chengdu, China
| | - Yan Wang
- State Key Laboratory of Oral Diseases, National Center for Stomatology, National Clinical Research Center for Oral Diseases, Department of Orthodontics, West China Hospital of Stomatology, Sichuan University, Chengdu, China
| |
Collapse
|
3
|
Ahmed OK, Kadhum AS. Effectiveness of laser-engineered copper-nickel titanium versus superelastic nickel-titanium aligning archwires: A randomized clinical trial. Korean J Orthod 2024; 54:16-25. [PMID: 38008906 PMCID: PMC10811358 DOI: 10.4041/kjod23.081] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/17/2023] [Revised: 08/18/2023] [Accepted: 08/29/2023] [Indexed: 11/28/2023] Open
Abstract
Objective : To compare the effectiveness of laser-engineered copper-nickel titanium (SmartArch) and superelastic nickel-titanium (SENT) archwires in aligning teeth and inducing root resorption and pain experienced by patients. Methods : Two-arm parallel groups with a 1:1 allocation ratio were used. The participants were patients aged 11.5 years and older with 5-9 mm of mandibular anterior crowding who were indicated for non-extraction treatment. The primary outcome was alignment effectiveness, assessed using Little's irregularity index (LII) over 16 weeks with a single wire (0.016-inch) in the SmartArch group and 2 wires (0.014- and 0.018-inch) in the SENT group (8 weeks each). Secondary outcomes included root resorption evaluated by pre- and post-intervention periapical radiographs and pain levels recorded by the participants during the first week. Results : A total of 40 participants were randomly allocated into 2 groups; 33 completed the study and were analyzed (16 in the SmartArch group and 17 in the SENT group, aged 16.97 ± 4.05 years). The total LII decrease for the SmartArch and SENT groups was 5.63 mm and 5.29 mm, respectively, which was neither statistically nor clinically significant. Root resorption was not significantly different between the groups. The difference in pain levels was not statistically significant for the first 5 days following wire placement; however, there was a significant difference favoring the SENT group in the final 2 days. Conclusions : SmartArch and SENT archwires were similarly effective during the alignment phase of orthodontic treatment. Root resorption should be observed throughout the treatment with either wire. SmartArch wires demonstrated higher pain perception than SENT wires.
Collapse
Affiliation(s)
- Omar Khairullah Ahmed
- Department of Orthodontics, College of Dentistry, University of Baghdad, Baghdad, Iraq
- Ministry of Health, Baghdad, Iraq
| | - Ammar Salim Kadhum
- Department of Orthodontics, College of Dentistry, University of Baghdad, Baghdad, Iraq
| |
Collapse
|
4
|
Sabbagh H, Janjic Rankovic M, Martin D, Mertmann M, Hötzel L, Wichelhaus A. Load Deflection Characteristics of Orthodontic Gummetal ® Wires in Comparison with Nickel-Titanium Wires: An In Vitro Study. MATERIALS (BASEL, SWITZERLAND) 2024; 17:533. [PMID: 38276472 PMCID: PMC10818840 DOI: 10.3390/ma17020533] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/27/2023] [Revised: 11/27/2023] [Accepted: 12/04/2023] [Indexed: 01/27/2024]
Abstract
The aim of this study was to investigate the load deflection characteristics of Gummetal® wires in comparison to nickel-titanium (NiTi) wires. Four different NiTi wires and one Gummetal® archwire were analyzed in two dimensions (0.014″ (0.36 mm) and 0.016″ × 0.022″ (0.41 mm × 0.56 mm)) and in two different orientations (edgewise and ribbonwise) using three-point bending tests at T = 37 °C. Force-displacement curves were recorded and analyzed. The Gummetal® 0.014″ wires exhibited higher forces compared to the NiTi wires at 2.0 mm deflection. At 1.0 mm deflection, the opposite pattern was observed. For the 0.016″ × 0.022″ Gummetal® wires, the forces were within the force interval of the NiTi wires at 2.0 mm deflection. At a deflection of 1.0 mm, no residual force was measurable for the Gummetal® wires. All the NiTi wires investigated showed hysteresis and a superelastic plateau. However, the Gummetal® did not form a plateau, but hysteresis was present. An easier plastic deformability compared to the NiTi wires was observed for all the tested geometries.
Collapse
Affiliation(s)
- Hisham Sabbagh
- Department of Orthodontics and Dentofacial Orthopedics, University Hospital, LMU Munich, Goethestrasse 70, 80366 Munich, Germany; (M.J.R.); (M.M.); (L.H.); (A.W.)
| | - Mila Janjic Rankovic
- Department of Orthodontics and Dentofacial Orthopedics, University Hospital, LMU Munich, Goethestrasse 70, 80366 Munich, Germany; (M.J.R.); (M.M.); (L.H.); (A.W.)
| | - Daniel Martin
- Dental Clinic, Medical Care Center, Untermeitingen, Landsbergerstrasse 7, 86836 Graben, Germany;
| | - Matthias Mertmann
- Department of Orthodontics and Dentofacial Orthopedics, University Hospital, LMU Munich, Goethestrasse 70, 80366 Munich, Germany; (M.J.R.); (M.M.); (L.H.); (A.W.)
| | - Linus Hötzel
- Department of Orthodontics and Dentofacial Orthopedics, University Hospital, LMU Munich, Goethestrasse 70, 80366 Munich, Germany; (M.J.R.); (M.M.); (L.H.); (A.W.)
| | - Andrea Wichelhaus
- Department of Orthodontics and Dentofacial Orthopedics, University Hospital, LMU Munich, Goethestrasse 70, 80366 Munich, Germany; (M.J.R.); (M.M.); (L.H.); (A.W.)
| |
Collapse
|
5
|
Bhatia NK, Chugh VK, Shankar SP, Vinay A P R, Singh S, Moungkhom P, Sardana R. Alignment efficiency and three-dimensional assessment of root resorption after alignment with conventional and copper-nickel-titanium archwires: A randomized controlled trial. Dental Press J Orthod 2024; 28:e2323177. [PMID: 38198391 PMCID: PMC10773444 DOI: 10.1590/2177-6709.28.6.e2323177.oar] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/11/2023] [Accepted: 10/23/2023] [Indexed: 01/12/2024] Open
Abstract
OBJECTIVE To compare alignment efficiency and root resorption between nickel-titanium (NiTi) and copper-nickel-titanium (CuNiTi) archwires after complete alignment in mandibular anterior region. METHODS In this two-arm parallel single-blind randomized controlled trial, forty-four patients with Class I malocclusion with mandibular anterior crowding were recruited form orthodontic clinic of All India Institute of Medical Sciences (Jodhpur, India). Patients were randomly allocated into NiTi and CuNiTi groups, with a 1:1 allocation. Alignment was performed using 0.014-in, 0.016-in, 0.018-in, 0.019x0.025-in archwire sequence in the respective groups, which terminated in 0.019 x 0.025-in stainless-steel working archwire. The primary outcome was alignment efficiency, measured on study models from baseline (T0) to the first, second, third, fourth and fifth-month (T5). Secondary outcome was root resorption, measured from CBCT scans taken at T0 and T5. Mixed-factorial ANOVA was used to compare Little's Irregularity Index (LII). For assessing the proportion of patients with complete alignment at the end of each month, Kaplan-Meier survival curve was built and time to treatment completion was compared between groups using log rank test. Paired t-test was used to assess external apical root resorption (EARR) within groups, whereas independent t-test was used to evaluate LII and EARR between the groups. RESULTS Twenty-two patients were recruited in each group. One patient was lost to follow-up in the CuNiTi group. No statistically significant differences were observed in alignment efficiency between the groups (p>0.05). Intergroup comparison revealed that the changes in root measurement in three-dimensions were not statistically significant (p>0.05), except for mandibular right central incisor, which showed increased resorption at root apex in NiTi group (p<0.01). CONCLUSION The two alignment archwires showed similar rate of alignment at all time points. Root resorption measurement did not differ between the NiTi and CuNiTi groups, except for the mandibular right central incisor, which showed more resorption in NiTi group.
Collapse
Affiliation(s)
- Navleen Kaur Bhatia
- All India Institute of Medical Sciences, Department of Dentistry, Section of Orthodontics (Jodhpur, Rajasthan, India)
| | - Vinay Kumar Chugh
- All India Institute of Medical Sciences, Department of Dentistry, Section of Orthodontics (Jodhpur, Rajasthan, India)
| | - Sam Prasanth Shankar
- All India Institute of Medical Sciences, Department of Dentistry, Section of Orthodontics (Jodhpur, Rajasthan, India)
| | - Ritvik Vinay A P
- All India Institute of Medical Sciences, Department of Dentistry, Section of Orthodontics (Jodhpur, Rajasthan, India)
| | - Surjit Singh
- All India Institute of Medical Sciences, Department of Pharmacology (Jodhpur, Rajasthan, India)
| | - Priyawati Moungkhom
- All India Institute of Medical Sciences, Department of Dentistry, Section of Orthodontics (Jodhpur, Rajasthan, India)
| | - Rinkle Sardana
- All India Institute of Medical Sciences, Department of Dentistry, Section of Orthodontics (Jodhpur, Rajasthan, India)
| |
Collapse
|
6
|
Hasan A, Hania M, Mandall N, Fleming PS. The scientific evidence for pre-adjusted edgewise attachments and mechanics. Br Dent J 2023:10.1038/s41415-023-6064-6. [PMID: 37474580 DOI: 10.1038/s41415-023-6064-6] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/29/2022] [Revised: 02/17/2023] [Accepted: 03/02/2023] [Indexed: 07/22/2023]
Abstract
Introduction Fixed orthodontic appliance systems continue to evolve with a wealth of evidence emerging to underpin these refinements.Aims To present the evidence from comparative prospective research informing the selection of fixed appliance design and mechanics.Design Detailed literature review.Materials and methods An electronic search to identify randomised controlled trials and clinical controlled trials was undertaken using pre-defined search terms.Results Based on high-level evidence, no one bracket system has been proven superior in terms of efficiency or outcome. Similarly, a clear advantage associated with one wire type or dimension has not been shown. The effect of lacebacks in terms of anchorage management appears to be limited, while elastomeric chain and nickel titanium closing coils are associated with similar rates of space closure.Discussion A wealth of high-quality recent evidence to support the selection of fixed appliance attachments, archwires and auxiliaries, including lacebacks and space closing mechanics, was identified.Conclusions There has been a considerable increase in the amount of high-quality evidence informing the choice of pre-adjusted edgewise mechanics in recent years. This information can be used to make evidence-based decisions in the selection and manipulation of fixed appliances during daily practice.
Collapse
Affiliation(s)
- Aliya Hasan
- Orthodontic Speciality Registrar, The Royal London Hospital, London, United Kingdom
| | - Mohamed Hania
- Orthodontic Speciality Senior Registrar, University Dental Hospital of Manchester, United Kingdom
| | - Nicky Mandall
- Consultant in Orthodontics, Tameside Hospital NHS Foundation Trust, Lancashire, United Kingdom
| | - Padhraig S Fleming
- Chair/Professor of Orthodontics, School of Dental Science, Trinity College Dublin, Ireland; Honorary Professor, Queen Mary University of London, United Kingdom.
| |
Collapse
|
7
|
Amaya González SY, Roncancio AP, Acuña EÁ, Guevara Barreto LA, Vargas NM, Plaza-Ruiz SP. Alignment efficiency of heat activated and superelastic nickel-titanium archwires in orthodontic patients over three months: A Single-center, randomized clinical trial. J Orthod Sci 2023; 12:9. [PMID: 37351408 PMCID: PMC10282515 DOI: 10.4103/jos.jos_19_22] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/14/2022] [Revised: 04/11/2022] [Accepted: 07/19/2022] [Indexed: 06/24/2023] Open
Abstract
OBJECTIVE The aim of this 2-arm parallel study was to evaluate the alignment efficiency of heat-activated nickel-titanium (NiTi-TE) and superelastic nickel titanium (NiTi-PSE) archwires over the first 3 months of orthodontic treatment and compare these groups. SETTING AND SAMPLE POPULATION Randomized, double-blind, controlled, single-center trial in 52 patients with fixed orthodontic appliances from an orthodontic graduate program in the permanent dentition and moderate crowding in the lower arch. MATERIAL AND METHODS Patients were randomly allocated to one of two interventions: NiTi-TE and NiTi-PSE archwires, 0.014-inch (3M Unitek™, CA, USA) with a follow-up period of 3 months. The primary outcome was the alignment efficiency determined by the reduction in Little's irregularity index (mm), measured in three points, T0: before the start of orthodontic treatment, T1: 1 month later, T2: 2 months later, T3: 3 months later. Data were analyzed using independent sample t tests and repeated measures ANOVA. RESULTS 52 patients (NiTi-TE n = 26; NiTi-PSE n = 26) were randomized and analyzed (average age: 21.73; standard deviation (SD): 6.07; average lower anterior irregularity: 5.20; SD: 0.76) for intention-to-treat (ITT) analysis. No statistically significant differences between the groups were found (mean of the differences: T1: 0.20; 95% CI: -0.558; 0.958; T2: 0.49: 95% CI: -0.339; 1.319; T3: 0.33; 95% CI: -0.308; 0.968). The resolution of crowding with each of the wires was significant (P < 0.0001) at all times. Twelve participants (2 treated with NiTi-TE and 10 treated with NiTi-PSE) lost follow-up due to face-to-face dental-procedures restrictions during the COVID-19 pandemic, the missing data was imputed. CONCLUSIONS NiTi-TE and NiTi-PSE wires of 0.014-inch were similar in their clinical efficiency for the resolution of crowding during the first 3 months of orthodontic treatment. REGISTRATION Clinical Trials NCT03256279.
Collapse
Affiliation(s)
- Suly Y. Amaya González
- Assistant Professor, Fundación Universitaria CIEO-UniCIEO, Bogotá, Colombia, Cra. 5 # 118-10, Bogotá, Cundinamarca, Colombia
| | - Alexandra Pérez Roncancio
- Assistant Professor, Fundación Universitaria CIEO-UniCIEO, Bogotá, Colombia, Cra. 5 # 118-10, Bogotá, Cundinamarca, Colombia
| | - Estefanía Ángel Acuña
- Orthodontic Program Resident, Fundación Universitaria CIEO-UniCIEO, Bogotá, Colombia, Cra. 5 # 118-10, Bogotá, Cundinamarca, Colombia
| | - Luz A. Guevara Barreto
- Orthodontic Program Resident, Fundación Universitaria CIEO-UniCIEO, Bogotá, Colombia, Cra. 5 # 118-10, Bogotá, Cundinamarca, Colombia
| | - Natalia Muñoz Vargas
- Orthodontic Program Resident, Fundación Universitaria CIEO-UniCIEO, Bogotá, Colombia, Cra. 5 # 118-10, Bogotá, Cundinamarca, Colombia
| | - Sonia P. Plaza-Ruiz
- Assistant Professor, Fundación Universitaria CIEO-UniCIEO, Bogotá, Colombia, Cra. 5 # 118-10, Bogotá, Cundinamarca, Colombia
| |
Collapse
|
8
|
Sirri MR, Burhan AS, Hajeer MY, Nawaya FR. Evaluation of Perceived Pain, Discomfort, Functional Impairments, and Satisfaction When Relieving Crowded Lower Anterior Teeth in Young Adult Patients Using Corticision-Assisted Fixed Orthodontic Treatment: A Randomized Controlled Trial. Cureus 2022; 14:e26489. [PMID: 35815305 PMCID: PMC9256009 DOI: 10.7759/cureus.26489] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Accepted: 07/01/2022] [Indexed: 11/05/2022] Open
|
9
|
Turner S, Harrison JE, Sharif FN, Owens D, Millett DT. Orthodontic treatment for crowded teeth in children. Cochrane Database Syst Rev 2021; 12:CD003453. [PMID: 34970995 PMCID: PMC8786262 DOI: 10.1002/14651858.cd003453.pub2] [Citation(s) in RCA: 6] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 01/02/2023]
Abstract
BACKGROUND Crowded teeth develop when there is not enough space in the jaws into which the teeth can erupt. Crowding can affect baby teeth (deciduous dentititon), adult teeth (permanent dentition), or both, and is a common reason for referral to an orthodontist. Crowded teeth can affect a child's self-esteem and quality of life. Early loss of baby teeth as a result of tooth decay or trauma, can lead to crowded permanent teeth. Crowding tends to increase with age, especially in the lower jaw. OBJECTIVES To assess the effects of orthodontic intervention for preventing or correcting crowded teeth in children. To test the null hypothesis that there are no differences in outcomes between different orthodontic interventions for preventing or correcting crowded teeth in children. SEARCH METHODS Cochrane Oral Health's Information Specialist searched four bibliographic databases up to 11 January 2021 and used additional search methods to identify published, unpublished and ongoing studies. SELECTION CRITERIA We included randomised controlled trials (RCTs) that evaluated any active interventions to prevent or correct dental crowding in children and adolescents, such as orthodontic braces or extractions, compared to no or delayed treatment, placebo treatment or another active intervention. The studies had to include at least 80% of participants aged 16 years and under. DATA COLLECTION AND ANALYSIS Two review authors, independently and in duplicate, extracted information regarding methods, participants, interventions, outcomes, harms and results. We resolved any disagreements by liaising with a third review author. We used the Cochrane risk of bias tool to assess the risk of bias in the studies. We calculated mean differences (MDs) with 95% confidence intervals (CI) for continuous data and odds ratios (ORs) with 95% CIs for dichotomous data. We undertook meta-analysis when studies of similar comparisons reported comparable outcome measures, using the random-effects model. We used the I2 statistic as a measure of statistical heterogeneity. MAIN RESULTS Our search identified 24 RCTs that included 1512 participants, 1314 of whom were included in analyses. We assessed 23 studies as being at high risk of bias and one as unclear. The studies investigated 17 comparisons. Twenty studies evaluated fixed appliances and auxiliaries (lower lingual arch, lower lip bumper, brackets, archwires, lacebacks, headgear and adjunctive vibrational appliances); two studies evaluated removable appliances and auxiliaries (Schwarz appliance, eruption guidance appliance); and two studies evaluated dental extractions (lower deciduous canines or third molars). The evidence should be interpreted cautiously as it is of very low certainty. Most interventions were evaluated by a single study. Fixed appliances and auxiliaries One study found that use of a lip bumper may reduce crowding in the early permanent dentition (MD -4.39 mm, 95% CI -5.07 to -3.71; 34 participants). One study evaluated lower lingual arch but did not measure amount of crowding. One study concluded that coaxial nickel-titanium (NiTi) archwires may cause more tooth movement in the lower arch than single-stranded NiTi archwires (MD 6.77 mm, 95% CI 5.55 to 7.99; 24 participants). Another study, comparing copper NiTi versus NiTi archwires, found NiTi to be more effective for reducing crowding (MD 0.49 mm, 95% CI 0.35 to 0.63, 66 participants). Single studies did not show evidence of one type of archwire being better than another for Titinol versus Nitinol; nickel-titanium versus stainless steel or multistrand stainless steel; and multistranded stainless steel versus stainless steel. Nor did single studies find evidence of a difference in amount of crowding between self-ligating and conventional brackets, active and passive self-ligating brackets, lacebacks added to fixed appliances versus fixed appliances alone, or cervical pull headgear versus minor interceptive procedures. Meta-analysis of two studies showed no evidence that adding vibrational appliances to fixed appliances reduces crowding at 8 to 10 weeks (MD 0.24 mm, 95% CI -0.81 to 1.30; 119 participants). Removable appliances and auxiliaries One study found use of the Schwarz appliance may be effective at treating dental crowding in the lower arch (MD -2.14 mm, 95% CI -2.79 to -1.49; 28 participants). Another study found an eruption guidance appliance may reduce the number of children with crowded teeth after one year of treatment (OR 0.19, 95% CI 0.05 to 0.68; 46 participants); however, this may have been due to an increase in lower incisor proclination in the treated group. Whether these gains were maintained in the longer term was not assessed. Dental extractions One study found that extracting children's lower deciduous canines had more effect on crowding after one year than no treatment (MD -4.76 mm, 95 CI -6.24 to -3.28; 83 participants), but this was alongside a reduction in arch length. One study found that extracting wisdom teeth did not seem to reduce crowding any more than leaving them in the mouth (MD -0.30 mm, 95% CI -1.30 to 0.70; 77 participants). AUTHORS' CONCLUSIONS Most interventions were assessed by single, small studies. We found very low-certainty evidence that lip bumper, used in the mixed dentition, may be effective for preventing crowding in the early permanent dentition, and a Schwarz appliance may reduce crowding in the lower arch. We also found very low-certainty evidence that coaxial NiTi may be better at reducing crowding than single-stranded NiTi, and that NiTi may be better than copper NiTi. As the current evidence is of very low certainty, our findings may change with future research.
Collapse
Affiliation(s)
- Sarah Turner
- Orthodontic Department, Liverpool University Dental Hospital, Liverpool, UK
| | - Jayne E Harrison
- Orthodontic Department, Liverpool University Dental Hospital, Liverpool, UK
| | | | - Darren Owens
- Orthodontic Department, Liverpool University Dental Hospital, Liverpool, UK
| | - Declan T Millett
- Oral Health and Development, Cork University Dental School and Hospital, Cork, Ireland
| |
Collapse
|
10
|
Wazwaz F, Seehra J, Carpenter GH, Ireland AJ, Papageorgiou SN, Cobourne MT. Duration of tooth alignment with fixed appliances: A systematic review and meta-analysis. Am J Orthod Dentofacial Orthop 2021; 161:20-36. [PMID: 34794862 DOI: 10.1016/j.ajodo.2021.06.016] [Citation(s) in RCA: 7] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/01/2021] [Revised: 06/01/2021] [Accepted: 06/01/2021] [Indexed: 12/11/2022]
Abstract
INTRODUCTION A key goal of orthodontic treatment with fixed appliances is alignment of the dentition, and this remains a commonly selected outcome in clinical studies investigating orthodontic tooth movement. This systematic review has evaluated treatment duration to achieve alignment of the mandibular dentition using fixed appliances. METHODS Systematic literature searches without restrictions were undertaken in 9 databases for randomized clinical trials (RCTs) assessing duration and rate of tooth alignment using fixed appliances with or without treatment adjuncts published up to January 2021. After duplicate study selection, data extraction, and risk of bias assessment according to Cochrane, random-effects meta-analyses of aggregate data, and individual patient data were conducted. RESULTS Thirty-five trials were included with 2258 participants (39% male; mean age 17.8 years), giving a pooled duration to achieve whole-arch alignment of the mandibular dentition of 263.0 days (4 trials; 95% confidence interval [CI], 186.7-339.4 days) and incisor alignment in the mandibular arch of 100.7 days (9 trials; 95% CI, 84.1-117.4 days). Surgical-assisted orthodontics was associated with reduced duration of incisor alignment: mean difference of 44.3 days less (4 trials; 95% CI, 20.0-68.9 days; P <0.001; high quality of evidence), whereas subgroup and meta-regression analyses indicated significant effects of baseline crowding and premolar extractions. Individual patient data analysis from 3 RCTs indicated that for each additional participant age year, whole-arch alignment of the mandibular dentition took 13.7 days longer (3 trials; 95% CI, 7.7-17.7 days; P <0.001) and for each additional mm of irregularity, 17.5 days more were needed (2 trials; 95% CI, 9.8-25.2 days; P <0.001). CONCLUSIONS Patient and treatment-related characteristics can significantly affect the duration of tooth alignment and should be taken into account both clinically and when designing trial outcomes. Future research studies investigating rates of orthodontic tooth alignment would benefit from adequate sample sizes and a more consistent methodology in outcome assessment. Data in this systematic review provides a basis for appropriate trial design for future RCTs investigating the rate of orthodontic tooth alignment with fixed appliances.
Collapse
Affiliation(s)
- Fidaa Wazwaz
- Department of Orthodontics, Faculty of Dentistry, Oral and Craniofacial Sciences, Centre for Craniofacial Development and Regeneration, King's College London, London, United Kingdom
| | - Jadbinder Seehra
- Department of Orthodontics, Faculty of Dentistry, Oral and Craniofacial Sciences, Centre for Craniofacial Development and Regeneration, King's College London, London, United Kingdom
| | - Guy H Carpenter
- Department of Mucosal Biology, Faculty of Dentistry, Oral and Craniofacial Sciences, Centre for Host Disease, King's College London, London, United Kingdom
| | - Anthony J Ireland
- Department of Orthodontics, University of Bristol Dental School, London, United Kingdom
| | - Spyridon N Papageorgiou
- Clinic of Orthodontics and Pediatric Dentistry, Center of Dental Medicine, University of Zurich, Zurich, Switzerland
| | - Martyn T Cobourne
- Department of Orthodontics, Faculty of Dentistry, Oral and Craniofacial Sciences, Centre for Craniofacial Development and Regeneration, King's College London, London, United Kingdom.
| |
Collapse
|
11
|
Jain S, Sharma P, Shetty D. Comparison of two different initial archwires for tooth alignment during fixed orthodontic treatment-A randomized clinical trial. J Orthod Sci 2021; 10:13. [PMID: 34568209 PMCID: PMC8423150 DOI: 10.4103/jos.jos_17_20] [Citation(s) in RCA: 5] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/31/2020] [Revised: 08/17/2020] [Accepted: 02/26/2021] [Indexed: 12/03/2022] Open
Abstract
OBJECTIVES: The aim of the study was to clinically evaluate and compare 0.016-inch superelastic nickel–titanium (NiTi) and 0.016-inch heat-activated nickel–titanium (NiTi) archwires in terms of alignment efficiency, root resorption, and pain intensity. METHOD: A total of 20 patients requiring fixed orthodontic treatment, having Little's irregularity index of 5–8, and requiring first premolar extractions were recruited. They were randomly allocated to receive two different archwires (0.016-inch superelastic NiTi or 0.016-inch thermoelastic NiTi). Good-quality impressions were taken of the lower arch before archwire placement (T0) and at every month after that till the alignment was complete. The rate of tooth alignment was measured on casts by determining Little's irregularity index. The pain experienced by the patient was assessed 24 hours and 1 week after the placement of the archwire on a visual analogue scale. Cone beam computed tomographic radiographs of lower anterior teeth were taken before and after alignment to assess root resorption. Data obtained were subjected to statistical analysis using the SPSS software (version 20.0). The level of significance was kept at 5%. RESULTS: The repeated measures ANOVA indicated that there was no significant difference in the aligning efficiency of superelastic and heat-activated NiTi wires. (p = 0.45). The Mann Whitney U test showed that superelastic NiTi wires had statistically significant higher VAS scores than heat-activated NiTi at 24 hours and 1-week interval (p < 0.05). Student's t-test indicated greater root resorption with superelastic NiTi but the difference was not statistically significant. CONCLUSION: Both the wires showed similar aligning efficiency and resulting root resorption. Superelastic NiTi was observed to produce more pain compared to heat-activated NiTi in the aligning phase.
Collapse
Affiliation(s)
- Shubhangi Jain
- Department of Orthodontics and Dentofacial Orthopedics, I.T.S-CDSR, Muradnagar, Ghaziabad, Uttar Pradesh, India
| | - Payal Sharma
- Department of Orthodontics and Dentofacial Orthopedics, I.T.S-CDSR, Muradnagar, Ghaziabad, Uttar Pradesh, India
| | - Divya Shetty
- Department of Orthodontics and Dentofacial Orthopedics, I.T.S-CDSR, Muradnagar, Ghaziabad, Uttar Pradesh, India
| |
Collapse
|
12
|
Azizi F, Extiari A, Imani MM. Tooth alignment and pain experience with A-NiTi versus Cu-NiTi: a randomized clinical trial. BMC Oral Health 2021; 21:431. [PMID: 34488744 PMCID: PMC8419894 DOI: 10.1186/s12903-021-01789-5] [Citation(s) in RCA: 7] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/17/2021] [Accepted: 08/28/2021] [Indexed: 11/20/2022] Open
Abstract
Background Nickel-titanium (NiTi) archwires are routinely used for initial leveling and alignment of teeth in orthodontic treatment. This study aimed to clinically compare the level of pain and tooth alignment in orthodontic treatment with A-NiTi versus Cu-NiTi archwires. Methods In this parallel randomized clinical trial, 88 orthodontic patients (12–25 years) with an irregularity index > 2 mm in the anterior site of the lower dental arch who required non-extraction orthodontic treatment of the lower arch were randomized into two age- and sex-matched groups (n = 44) for treatment with A-NiTi and Cu-NiTi initial archwires. Each archwire was used for 6 weeks. After 6 weeks, the irregularity index was measured, and the level of pain was scored using the Modified McGill pain questionnaire (MPQ) and visual analog scale (VAS) according to the time of onset and duration of pain, and analgesic intake. Data were analyzed by paired t test, independent samples t test, and Chi-square test (P < 0.05). Results The irregularity index significantly decreased in both groups after 6 weeks of treatment (P < 0.001). However, the difference in this respect was not significant between the two groups (P > 0.05). Pain perception (P = 0.487), duration of pain (P = 0.546), and analgesic intake (P = 0.102) were not significantly different between the two groups either. Conclusion Both A-NiTi and Cu-NiTi archwires are equally effective for tooth alignment in the anterior site of the lower dental arch and have no significant difference with regard to the level of pain experienced by patients. Trial registration number: IRCT20190705044102N1 and Name of the registry: Iranian registry of clinical trials (https://irct.ir/)
Date of registration: September, 26, 2019
Collapse
Affiliation(s)
- Fatemeh Azizi
- Department of Orthodontics, Faculty of Dentistry, Kermanshah University of Medical Sciences, Kermanshah, Iran
| | - Aida Extiari
- Students Research Committee, Kermanshah University of Medical Sciences, Kermanshah, Iran
| | - Mohammad Moslem Imani
- Department of Orthodontics, Faculty of Dentistry, Kermanshah University of Medical Sciences, Kermanshah, Iran.
| |
Collapse
|
13
|
Theerasopon P, Lindauer SJ, Charoemratrote C. Separation of aligning and leveling stages to control mandibular incisor inclination: A randomized clinical trial. Dental Press J Orthod 2021; 26:e2119378. [PMID: 33950082 PMCID: PMC8103905 DOI: 10.1590/2177-6709.26.2.e2119378.oar] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/15/2019] [Accepted: 05/24/2020] [Indexed: 11/22/2022] Open
Abstract
OBJECTIVE To determine whether separating the alignment and leveling phases can reduce proclination of the mandibular incisors. METHODS Eligibility criteria included Class I subjects with an irregularity index of 3-5 mm, 3-4 mm curve-of-Spee (COS), and non-extraction treatment. Thirty adults were randomly allocated into two groups: (1) Control group was leveled and aligned simultaneously with flat archwires progressively to 0.016x0.022-in stainless-steel; (2) Experimental group was aligned first with 0.014-in-superelastic NiTi with mild accentuated COS, then leveled using 0.016x0.022-in beta-titanium accentuated COS archwires and gradually reduced the curve until flat. Mandibular incisor position and inclination were evaluated by cephalometric analysis. COS and irregularity index were evaluated in study models. Assessment was conducted twice after 0.016-in NiTi and after 0.016x0.022-in stainless-steel archwire placements. Dental changes from cephalograms and models were compared within group using paired t-test and between groups using independent t-test. RESULTS Control group: Round-wire-phase, mandibular incisors tipped labially (4.38° and 1 mm) with intrusion (-1.13 mm); Rectangular-wire-phase, mandibular incisors further intruded and proclined (-0.63 mm and 1.38°). Experimental group: During aligning with round accentuated COS archwires, mandibular incisors tipped very slightly labially (0.75° and 0.50 mm) with no significant intrusion; during leveling with rectangular archwires, incisors majorly intruded (1.75 mm) with slight proclination (1.81°). The experimental group had significant less incisor proclination (control: 5.76°, experimental: 2.56°) with more incisor intrusion (control: -1.75 mm, experimental: -2.13 mm). The COS in experimental group showed significant greater reduction (-2.88 mm) than that of the control group (-1.69 mm). CONCLUSION In control group, mandibular incisor proclination was markedly observed in round archwires, with further proclination caused by rectangular archwires. In experimental group, minimal proclination was exhibited when accentuated COS round archwires were used for aligning. Leveling with rectangular archwires caused less proclination with more COS reduction.
Collapse
Affiliation(s)
- Pornpat Theerasopon
- University of Phayao, School of Dentistry, Department of Orthodontics (Phayao, Thailand)
| | - Steven J Lindauer
- Virginia Commonwealth University, School of Dentistry, Department of Orthodontics (Richmond/VA, USA)
| | - Chairat Charoemratrote
- Prince of Songkla University, Faculty of Dentistry, Department of Preventive Dentistry (Songkhla, Thailand)
| |
Collapse
|
14
|
Nabbat SA, Yassir YA. A clinical comparison of the effectiveness of two types of orthodontic aligning archwire materials: a multicentre randomized clinical trial. Eur J Orthod 2020; 42:626-634. [PMID: 32011678 DOI: 10.1093/ejo/cjz102] [Citation(s) in RCA: 9] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/13/2022]
Abstract
OBJECTIVES To compare the heat-activated nickel titanium (HANT) with superelastic nickel-titanium (SENT) archwires in terms of their effectiveness of aligning teeth, possibility of inducing root resorption, and perception of pain. SUBJECTS AND METHODS Orthodontic patients aged 12 years or over with mandibular anterior crowding of 3-6 mm, who required treatment without extractions were randomly allocated (a simple non-stratified randomization) to the HANT and SENT archwires groups with a 1:1 allocation ratio. The archwire sequence in both groups was 0.014-inch and 0.016-inch, respectively. Each archwire was placed for 4 weeks. The outcome measures included the amount of crowding assessed blindly using Little's irregularity index (LII), apical root resorption, and pain perception. The effectiveness of alignment was tested using 2 × 2 mixed factorial analysis of variance (ANOVA) model, while root resorption and pain perception were tested by the Mann-Whitney U-test and Wilcoxon signed-rank test (P < 0.05). RESULTS Thirty-four patients were randomized and recruited from four centres, of those 31 were analysed (15 participants for the HANT and 16 for the SENT groups) with an overall mean age of 19.13 ± 5.73 years. The total reduction in the LII was 2.69 mm and 2.74 mm for the HANT and SENT groups, respectively. This did not reach the level of statistical (P = 0.809) or clinical significance. Similarly, root resorption and pain perception showed non-significant difference between groups. However, there was a slight increase in root resorption with the SENT group. LIMITATIONS A long-term evaluation of root resorption is required. CONCLUSIONS Both HANT and SENT archwires were equally effective in the aligning stage of orthodontic treatment. Root resorption with SENT wires should be monitored throughout treatment. REGISTRATION The trial was registered with ClinicalTrials.gov on 18 September 2019, registration number: NCT04090931.
Collapse
Affiliation(s)
- Sarah A Nabbat
- Department of Orthodontic, College of Dentistry, University of Baghdad, Iraq
| | - Yassir A Yassir
- Department of Orthodontic, College of Dentistry, University of Baghdad, Iraq
| |
Collapse
|
15
|
Amaya S, Pérez A, Guzmán H, Espinosa A, Motta G, Mojica J, Plaza-Ruiz SP. Changes in the mechanical properties of two nickel-titanium archwires after 3 months of clinical usage. J World Fed Orthod 2020; 9:175-180. [PMID: 33168487 DOI: 10.1016/j.ejwf.2020.10.001] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/10/2020] [Revised: 10/08/2020] [Accepted: 10/12/2020] [Indexed: 11/24/2022]
Abstract
BACKGROUND Nickel-titanium archwires have unique mechanical properties that make them the archwire of choice during the first phase of orthodontic treatment. However, during its clinical use when subjected to oral conditions, these properties can undergo great changes. MATERIALS AND METHODS A sample of 24 randomly chosen superelastic NiTi orthodontic archwires (12 TE and 12 PSE) with a 0.014-inch round section from the same manufacturer were distributed into four groups of six archwires each. The first two groups were new wires (as-received), which were used as controls (T0), and the other two were collected after 3 months of clinical usage (as-retrieved) in orthodontic patients (T1). Mechanical properties were measured by mechanical tensile testing and three-point bending tests under the same experimental and temperature conditions (36°C) in a universal testing machine. Comparisons between the groups at T0 and T1 were performed with t-tests and Mann-Whitney U tests. A paired t-test and Wilcoxon signed rank sum test were used for intragroup comparisons (T1-T0). RESULTS At baseline, PSE wires presented significantly (P < 0.05) higher load at fracture, range, ultimate tensile strength (UTS), yield strength, springback, maximum tension and flexural ultimate strength (FUS) than those of TE wires. At T1, a significant decrease in load at fracture and UTS in PSE wires and in FUS in TE wires was found. After 3 months of clinical usage, the changes (T1-T0) in the mechanical properties of both alloys were similar. CONCLUSIONS After 3 months of clinical usage, wires lost some of their mechanical properties and had less resistance to breakage. However, the as-received differences between both wires were maintained after clinical usage.
Collapse
Affiliation(s)
- Suly Amaya
- Assistant Professor, Orthodontic Department, Fundación Universitaria CIEO UniCIEO, Bogotá, Colombia.
| | - Alexandra Pérez
- Assistant Professor, Orthodontic Department, Fundación Universitaria CIEO UniCIEO, Bogotá, Colombia
| | - Humberto Guzmán
- Associate Professor, Orthodontic Department, Fundación Universitaria CIEO UniCIEO, Bogotá, Colombia
| | - Andrés Espinosa
- Orthodontic Program Resident, Orthodontic Department, Fundación Universitaria CIEO UniCIEO, Bogotá, Colombia
| | - Grecia Motta
- Orthodontic Program Resident, Orthodontic Department, Fundación Universitaria CIEO UniCIEO, Bogotá, Colombia
| | - Juan Mojica
- Orthodontic Program Resident, Orthodontic Department, Fundación Universitaria CIEO UniCIEO, Bogotá, Colombia
| | - Sonia P Plaza-Ruiz
- Associate Professor, Orthodontic Department, Fundación Universitaria CIEO UniCIEO, Bogotá, Colombia
| |
Collapse
|
16
|
Effectiveness of two thermal activated orthodontic archwire sequences based on transition temperature range during alignment: A randomized non-controlled comparative study. Int Orthod 2020; 18:706-713. [PMID: 33071153 DOI: 10.1016/j.ortho.2020.09.006] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/07/2020] [Revised: 09/16/2020] [Accepted: 09/20/2020] [Indexed: 11/24/2022]
Abstract
INTRODUCTION It has been suggested that heat-activated NiTi archwires (HANT) speed up crowding alleviation. HANT wires are available with different austenite finish temperatures. OBJECTIVE The aim of the present study was to compare the effectiveness of two alignment sequences using thermally activated archwires with different austenite activation temperatures for the correction of mandibular anterior crowding. MATERIAL AND METHODS The following NiTi archwire sequence was used for both groups: 0.012 in (conventional NiTi), 0.018 in (heat-activated NiTi archwires), 0.016×0.022 in (heat-activated NiTi archwires) and 0.019×0.025 in (conventional NiTi). The conventional NiTi used for both groups belongs to the same commercial brand. Two different austenite activation temperatures (35°C and 37°C) were used for the heat-activated archwires. The primary outcome was the degree of crowding correction measured on study models. The secondary outcome was crowding survival time over a six-month period. This RTC included fifty-four patients that were randomly allocated to the two different archwire sequences. A Mann-Whitney test was used to compare the groups regarding crowding alleviation. A survival curve was created using the Kaplan-Meier method to illustrate the reduction of crowding over time. A Mantel-Cox log-rank test was used to compare survival times (until correction of crowding). RESULTS No differences in crowding alleviation were identified between both groups (log-rank test; P=0.77). CONCLUSIONS The two alignment sequences with different thermal activated archwires at 35°C and 37°C achieved similar clinical results during the correction of mandibular anterior crowding.
Collapse
|
17
|
Sapata VM, Sapata DM, Gurgel JA, Neto AM, Ramos AL. DSC analysis and evaluation of forces released on deactivation of 0.40-mm (0.016") orthodontic thermo-activated NiTi wires: An in vitro study. J Dent Res Dent Clin Dent Prospects 2020; 14:12-18. [PMID: 32454953 PMCID: PMC7235700 DOI: 10.34172/joddd.2020.002] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/09/2022] Open
Abstract
Background
. This study evaluated the phase transformation of NiTi orthodontic wires and forces they release on deactivation. Methods. The structural phase transformations of the following five thermo-activated nickel-titanium (NiTi) wires were evaluated using differential scanning calorimetry (DSC): Flexy Thermal Sentalloy® (GAC International), NiTi (35ºC) (Eurodonto), Thermo-Plus® (Morelli), FlexyNiTi® Flexy Thermal (35ºC) (Orthometric) and Damon® CuNiTi (35ºC) (ORMCO Corp.). The wires had a cross-section of 0.40 mm (0.016"). In addition, the forces they released were investigated using the three-point bending test. Five arches of each wire were tested using DSC (-20/80ºC at 10ºC/min), and six arches from each wire were sectioned for bending tests. The data were analyzed with ANOVA and post hoc Tukey tests. Pearson’s correlation test was performed between the results yielded by the DSC tests and those by three-point analyses (P=0.05). Results. The DSC analysis showed differences between the NiTi alloys from all the manufacturers, with no differences between the lots of the same brand. ORMCO and Orthometric wires exhibited similar TTR values in cooling (P=0.49), and statistically similar TTR values in heating (P=0.056). The three-point bending test showed different patterns in releasing forces. A correlation was found between the DSC analysis and the three-point bending test results. Conclusion. The higher the temperature transformation was, the larger was the variation of force. All the wires presented higher forces at 3-mm deflection from 155 (±12.3) to 168.1 (±8) cN. The DSC analysis and the three-point bending test showed differences between the NiTi alloys from all the manufacturers.
Collapse
Affiliation(s)
| | | | | | | | - Adilson Luiz Ramos
- Department of Dentistry, Universidade Estadual Maringá, Maringá, PR, Brazil
| |
Collapse
|
18
|
A comparative assessment of clinical efficiency between premium heat-activated copper nickel-titanium and superelastic nickel-titanium archwires during initial orthodontic alignment in adolescents: a randomized clinical trial. Prog Orthod 2019; 20:46. [PMID: 31840204 PMCID: PMC6911816 DOI: 10.1186/s40510-019-0299-4] [Citation(s) in RCA: 16] [Impact Index Per Article: 3.2] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/25/2019] [Accepted: 11/12/2019] [Indexed: 11/29/2022] Open
Abstract
Background To compare the clinical efficiency of premium heat-activated copper nickel-titanium (Tanzo Cu-NiTi) and NT3 superelastic NiTi during initial orthodontic alignment. Subject and methods A total of 50 patients were randomly allocated to 1 of 2 different archwire types (group 1, Tanzo Cu-NiTi; group 2, NT3 superelastic NiTi). Eligibility criteria included Class I or Class II malocclusion, moderate maxillary anterior crowding, and healthy periodontal condition. Impressions of the upper arches were taken before archwire placement (T0) and at every 4 weeks (T1, T2, T3, and T4). For T1 and T2 stages, 0.014-in., and for T3 and T4 stages, 0.018-in. archwires were used. The primary outcome was the alignment efficiency assessed using Little’s irregularity index. The secondary outcomes were arch width and incisor inclination changes. Data were analyzed using independent samples t test, repeated measures ANOVA, and Mann-Whitney U test. Marginal models were established for the estimation of coefficients. Results The anterior irregularity index reduction was mostly observed between T0 and T2 periods, which were respectively − 7.40 ± 0.50 mm (p < 0.001; 95% CI, − 8.94, − 5.85) and − 6.80 ± 0.55 mm (p < 0.001; 95% CI, − 8.49, − 5.12) for groups 1 and 2 (p < 0.001). With both wires, Little’s irregularity index decreased over time, and the difference between the groups was not significant (p = 0.581; estimated effect size, 0.011). No statistically significant difference was found between the groups in terms of intercanine and intermolar width and incisor inclination changes. Conclusion There were no significant between-group differences in alignment efficiency, arch width, and incisor inclination change. There was an increased alignment with 0.014-in. compared with 0.018-in. diameter archwire.
Collapse
|
19
|
Aksoy A, Cesur MG, Dağdeviren BH, Özkaynak YA, Karacin G, Gültekin F. Assessment of Pain, Anxiety, and Cortisol Levels During the Initial Aligning Phase of Fixed Orthodontic Treatment. Turk J Orthod 2019; 32:34-40. [PMID: 30944898 DOI: 10.5152/turkjorthod.2019.18043] [Citation(s) in RCA: 6] [Impact Index Per Article: 1.2] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/01/2018] [Accepted: 07/09/2018] [Indexed: 11/22/2022]
Abstract
Objective We assessed pain and anxiety using psychological testing instruments (State-Trait Anxiety Inventory for Children, visual analog scale) and a physiological testing instrument (salivary cortisol hormone level) after the insertion of orthodontic appliances and during the initial alignment phase of orthodontic treatment. Methods The study group involved two groups matched according to age and gender. Group 1 used 0.016-, 0.016×0.016-, and 0.16×0.22-inch and Group 2 used 0.014-, 0.016-, and 0.016×0.016-inch superelastic nickel-titanium archwires in the initial alignment phase of treatment. Pain and anxiety instruments were applied, and saliva samples were collected from the patients before and after molar band insertions, and bracket and initial archwire placement, and 7 days after the initial bonding and archwire replacements. Results Cortisol levels and state anxiety scores revealed statistically significant differences within groups (p<0.01, p<0.05). No significant differences were found between Group 1 and Group 2 in cortisol hormone levels, anxiety scores, or pain measurements (p>0.05). Although not statistically significant, the most severe pain was measured in the posterior teeth after band insertion and in the anterior teeth after the first archwire insertion (p>0.05). Conclusion Orthodontic appliances and the initial alignment phase of orthodontic treatment affect patients' anxiety and cortisol hormone levels. Both archwires were equally effective with regard to perceived pain, anxiety, and stress hormone levels.
Collapse
Affiliation(s)
- Alev Aksoy
- Department of Orthodontics, Süleyman Demirel University School of Medicine, Isparta, Turkey
| | - Mine Geçgelen Cesur
- Department of Orthodontics, Adnan Menderes University School of Dentistry, Aydın, Turkey
| | | | | | - Gizem Karacin
- Department of Orthodontics, Süleyman Demirel University School of Medicine, Isparta, Turkey
| | - Fatih Gültekin
- Department of Medical Biochemisrtry, Health Sciences University School of Medicine, İstanbul, Turkey
| |
Collapse
|
20
|
Sebastian B, Abraham ME, Sarma PS, Cherian KK. Alignment efficiency of coaxial tubular superelastic nickel-titanium vs single-stranded superelastic nickel-titanium in relieving mandibular anterior crowding in extraction cases: A single-centre randomized controlled clinical trial. Orthod Craniofac Res 2019; 22:105-111. [PMID: 30657251 DOI: 10.1111/ocr.12289] [Citation(s) in RCA: 5] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/12/2018] [Revised: 01/09/2019] [Accepted: 01/10/2019] [Indexed: 11/29/2022]
Abstract
OBJECTIVES To compare the alignment efficiency of coaxial tubular and single-stranded 0.016" superelastic NiTi archwires in relieving mandibular anterior crowding in extraction cases and to evaluate whether alignment efficiency differed as the initial irregularity increased. SETTING AND SAMPLE POPULATION Forty female patients aged between twelve and twenty years from the postgraduate orthodontic clinic at the authors' centre. MATERIALS AND METHODS All patients in this single-centre, 2-arm parallel trial were randomly allocated in a 1:1 ratio and the mandibular anterior irregularity was measured from the mandibular cast at 0-, 4-, 8- and 12-week intervals using a digital calliper. RESULTS All forty patients (mean age, 15.08 ± 2.11) completed the study with either coaxial tubular superelastic NiTi (mean age, 15.30 ± 2.36) or single-stranded superelastic NiTi (mean age, 14.85 ± 1.84). The largest mean irregularity index reduction of -4.88 ± 2.74 and -6.17 ± 2.38 in the single-stranded superelastic NiTi and the coaxial tubular superelastic NiTi groups, respectively (P = 0.122) was at 4 weeks. Student's t test and repeated measures ANOVA indicated that none of the mean comparisons were statistically significant at a 5% level. Pearson's correlation value (r) indicated no statistically significant influence of initial crowding on alignment efficiency. CONCLUSIONS There was no statistically significant difference between the alignment efficiency of coaxial tubular superelastic NiTi and single-stranded superelastic NiTi in extraction cases, and the degree of initial crowding had no influence on the alignment efficiency.
Collapse
Affiliation(s)
- Biju Sebastian
- Department of Orthodontics, Pushpagiri College of Dental Sciences, Tiruvalla, India
| | - Merin Elsa Abraham
- Department of Orthodontics, Pushpagiri College of Dental Sciences, Tiruvalla, India
| | | | - Karun Koshy Cherian
- Department of Orthodontics, Pushpagiri College of Dental Sciences, Tiruvalla, India
| |
Collapse
|
21
|
Wang Y, Liu C, Jian F, McIntyre GT, Millett DT, Hickman J, Lai W. Initial arch wires used in orthodontic treatment with fixed appliances. Cochrane Database Syst Rev 2018; 7:CD007859. [PMID: 30064155 PMCID: PMC6513532 DOI: 10.1002/14651858.cd007859.pub4] [Citation(s) in RCA: 9] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 02/05/2023]
Abstract
BACKGROUND Initial arch wires are the first arch wires to be inserted into the fixed appliance at the beginning of orthodontic treatment and are used mainly for the alignment of teeth by correcting crowding and rotations. With a number of different types of orthodontic arch wires available for initial tooth alignment, it is important to understand which wire is most efficient, as well as which wires cause least amount of root resorption and pain during the initial aligning stage of treatment. This is an update of the review entitledInitial arch wires for alignment of crooked teeth with fixed orthodontic braces, which was first published in 2010. OBJECTIVES To assess the effects of initial arch wires for the alignment of teeth with fixed orthodontic braces, in terms of the rate of tooth alignment, amount of root resorption accompanying tooth movement, and intensity of pain experienced by patients during the initial alignment stage of treatment. SEARCH METHODS Cochrane Oral Health's Information Specialist searched the following databases: Cochrane Oral Health's Trials Register (to 5 October 2017), the Cochrane Central Register of Controlled Trials (CENTRAL) (the Cochrane Library, 2017, Issue 9), MEDLINE Ovid (1946 to 5 October 2017), and Embase Ovid (1980 to 5 October 2017. The US National Institutes of Health Trials Registry (ClinicalTrials.gov) and the World Health Organization International Clinical Trials Registry Platform were searched for ongoing trials. No restrictions were placed on the language or date of publication when searching the electronic databases. SELECTION CRITERIA We included randomised controlled trials (RCTs) of initial arch wires to align teeth with fixed orthodontic braces. We included only studies involving participants with upper or lower, or both, full arch fixed orthodontic appliances. DATA COLLECTION AND ANALYSIS Two review authors were responsible for study selection, 'Risk of bias' assessment and data extraction. We resolved disagreements by discussion between the review authors. We contacted corresponding authors of included studies to obtain missing information. We assessed the quality of the evidence for each comparison and outcome as high, moderate, low or very low, according to GRADE criteria. MAIN RESULTS For this update, we found three new RCTs (228 participants), bringing the total to 12 RCTs with 799 participants. We judged three studies to be at high risk of bias, and three to be at low risk of bias; six were unclear. None of the studies reported the adverse outcome of root resorption. The review assessed six comparisons.1. Multistrand stainless steel versus superelastic nickel-titanium (NiTi) arch wires. There were five studies in this group and it was appropriate to undertake a meta-analysis of two of them. There is insufficient evidence from these studies to determine whether there is a difference in rate of alignment between multistrand stainless steel and superelastic NiTi arch wires (mean difference (MD) -7.5 mm per month, 95% confidence interval (CI) -26.27 to 11.27; 1 study, 48 participants; low-quality evidence). The findings for pain at day 1 as measured on a 100 mm visual analogue scale suggested that there was no meaningful difference between the interventions (MD -2.68 mm, 95% CI -6.75 to 1.38; 2 studies, 127 participants; moderate-quality evidence).2. Multistrand stainless steel versus thermoelastic NiTi arch wires. There were two studies in this group, but it was not appropriate to undertake a meta-analysis of the data. There is insufficient evidence from the studies to determine whether there is a difference in rate of alignment between multistrand stainless steel and thermoelastic NiTi arch wires (low-quality evidence). Pain was not measured.3. Conventional NiTi versus superelastic NiTi arch wires. There were three studies in this group, but it was not appropriate to undertake a meta-analysis of the data. There is insufficient evidence from these studies to determine whether there is any difference between conventional and superelastic NiTi arch wires with regard to either alignment or pain (low- to very low-quality evidence).4. Conventional NiTi versus thermoelastic NiTi arch wires. There were two studies in this group, but it was not appropriate to undertake a meta-analysis of the data. There is insufficient evidence from these studies to determine whether there is a difference in alignment between conventional and thermoelastic NiTi arch wires (low-quality evidence). Pain was not measured.5. Single-strand superelastic NiTi versus coaxial superelastic NiTi arch wires. There was only one study (24 participants) in this group. There is moderate-quality evidence that coaxial superelastic NiTi can produce greater tooth movement over 12 weeks (MD -6.76 mm, 95% CI -7.98 to -5.55). Pain was not measured.6. Superelastic NiTi versus thermoelastic NiTi arch wires. There were three studies in this group, but it was not appropriate to undertake a meta-analysis of the data. There is insufficient evidence from these studies to determine whether there is a difference in alignment or pain between superelastic and thermoelastic NiTi arch wires (low-quality evidence). AUTHORS' CONCLUSIONS Moderate-quality evidence shows that arch wires of coaxial superelastic nickel-titanium (NiTi) can produce greater tooth movement over 12 weeks than arch wires made of single-strand superelastic NiTi. Moderate-quality evidence also suggests there may be no difference in pain at day 1 between multistrand stainless steel arch wires and superelastic NiTi arch wires. Other than these findings, there is insufficient evidence to determine whether any particular arch wire material is superior to any other in terms of alignment rate, time to alignment, pain and root resorption.
Collapse
Affiliation(s)
- Yan Wang
- West China Hospital of Stomatology, Sichuan UniversityDepartment of Orthodontics, State Key Laboratory of Oral DiseasesNo. 14, Section Three, Ren Min Nan RoadChengduSichuanChina610041
| | - Chang Liu
- West China Hospital of Stomatology, Sichuan UniversityDepartment of Oral and Maxillofacial Surgery, State Key Laboratory of Oral DiseasesNO.14, 3rd Section of Ren Min Nan RoadChengduSichuanChina610041
| | - Fan Jian
- West China Hospital of Stomatology, Sichuan UniversityDepartment of Orthodontics, State Key Laboratory of Oral DiseasesNo. 14, Section Three, Ren Min Nan RoadChengduSichuanChina610041
| | - Grant T McIntyre
- University of DundeeSchool of Dentistry2 Park PlaceDundeeScotlandUKDD1 4HR
| | - Declan T Millett
- Cork University Dental School and HospitalOral Health and DevelopmentUniversity CollegeCorkIreland
| | - Joy Hickman
- Glan Clwyd HospitalDepartment of OrthodonticsRhylUKLL18 5UJ
| | - Wenli Lai
- West China Hospital of Stomatology, Sichuan UniversityDepartment of Orthodontics, State Key Laboratory of Oral DiseasesNo. 14, Section Three, Ren Min Nan RoadChengduSichuanChina610041
| | | |
Collapse
|
22
|
Aydın B, Şenışık NE, Koşkan Ö. Evaluation of the alignment efficiency of nickel-titanium and copper-nickel-titanium archwires in patients undergoing orthodontic treatment over a 12-week period: A single-center, randomized controlled clinical trial. Korean J Orthod 2018; 48:153-162. [PMID: 29732301 PMCID: PMC5932317 DOI: 10.4041/kjod.2018.48.3.153] [Citation(s) in RCA: 14] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/20/2017] [Revised: 08/29/2017] [Accepted: 10/07/2017] [Indexed: 11/24/2022] Open
Abstract
Objective The aim of this trial was to compare the alignment efficiency and intermaxillary arch dimension changes of nickel-titanium (NiTi) or copper-nickel-titanium (CuNiTi) round archwires with increasing diameters applied sequentially to the mandibular arch. Methods The initial alignment phase of fixed orthodontic treatment with NiTi or CuNiTi round archwires was studied in a randomly allocated sample of 66 patients. The NiTi group comprised 26 women, 10 men, and the CuNiTi (27℃) group comprised 20 women, 10 men. The eligibility criteria were as follows: anterior mandibular crowding of minimum 6 mm according to Little's Irregularity Index (LII), treatment requiring no extraction of premolars, 12 to 18 years of age, permanent dentition, skeletal and dental Class I malocclusion. The main outcome measure was the alignment of the mandibular anterior dentition; the secondary outcome measure was the change in mandibular dental arch dimensions during 12 weeks. Simple randomization (allocation ratio 1:1) was used in this single-blind study. LII and mandibular arch dimensions were measured on three-dimensional digital dental models at 2-week intervals. Results No statistically significant difference was observed between NiTi and CuNiTi according to LII (p > 0.05). Intercanine and intermolar arch perimeters increased in the CuNiTi group (p < 0.001). Inter-first premolar width showed a statistically significant interaction in week × diameter × application (p < 0.05). Conclusions The effects of NiTi and CuNiTi round archwires were similar in terms of their alignment efficiency. However, the intercanine and intermolar arch perimeters, and the inter-first premolar width changes differed between groups.
Collapse
Affiliation(s)
- Burcu Aydın
- Department of Orthodontics, Faculty of Dentistry, Suleyman Demirel University, Isparta, Turkey
| | - Neslihan Ebru Şenışık
- Department of Orthodontics, Faculty of Dentistry, Suleyman Demirel University, Isparta, Turkey
| | - Özgür Koşkan
- Departments of Animal Science, Genetics, and Biometrics, Faculty of Agriculture, Suleyman Demirel University, Isparta, Turkey
| |
Collapse
|
23
|
Nordstrom B, Shoji T, Anderson WC, Fields HW, Beck FM, Kim DG, Takano-Yamamoto T, Deguchi T. Comparison of changes in irregularity and transverse width with nickel-titanium and niobium-titanium-tantalum-zirconium archwires during initial orthodontic alignment in adolescents: A double-blind randomized clinical trial. Angle Orthod 2018; 88:348-354. [PMID: 29504810 DOI: 10.2319/061417-393.1] [Citation(s) in RCA: 19] [Impact Index Per Article: 3.2] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/23/2022] Open
Abstract
OBJECTIVES The purpose of this prospective, double-blind, randomized clinical trial was to compare the clinical efficiency of nickel-titanium (NiTi) and niobium-titanium-tantalum-zirconium (TiNbTaZr) archwires during initial orthodontic alignment. MATERIALS AND METHODS All subjects (ages between 12 and 20 years) underwent nonextraction treatment using 0.022-inch brackets. All patients were randomized into two groups for initial alignment with 0.016-inch NiTi archwires (n = 14), or with 0.016-inch TiNbTaZr archwires (n = 14). Digital scans were taken during the course of treatment and were used to compare the improvement in Little's Irregularity Index and the changes in intercanine and intermolar widths. RESULTS There was approximately a 27% reduction in crowding during the first month with the use of 0.016-inch TiNbTaZr (Gummetal) wire, and an additional 25% decrease in crowding was observed during the next month. There was no significant difference between the two treatment groups in the decrease in irregularity over time ( P = .29). There was no significant difference between the two groups in the changes in intercanine and intermolar width ( P = .80). CONCLUSIONS It can be concluded that Gummetal wires and conventional NiTi wires possess a similar ability to align teeth, and Gummetal wires have additional advantages over conventional NiTi, such as formability and use in patients with nickel allergy.
Collapse
|
24
|
Comparison of arch width and depth changes and pain/discomfort with conventional and copper Ni-Ti archwires for mandibular arch alignment. J World Fed Orthod 2018. [DOI: 10.1016/j.ejwf.2018.01.001] [Citation(s) in RCA: 4] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/20/2022]
|
25
|
Mahmoudzadeh M, Farhadian M, Alijani S, Azizi F. Comparaison de deux arcs initiaux (A-NiTi et NiTi thermiques) pour évaluer la quantité d’alignement dentaire et la perception de la douleur : étude clinique randomisée. Int Orthod 2018; 16:60-72. [PMID: 29478924 DOI: 10.1016/j.ortho.2018.01.008] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.2] [Reference Citation Analysis] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/29/2022]
Affiliation(s)
- Majid Mahmoudzadeh
- Département d'orthodontie, faculté dentaire, université de sciences médicales, Hamadan, Iran
| | - Maryam Farhadian
- Unité de recherche de modélisation, biostatistique et santé publique des maladies non transmissibles, université d'Hamadan de sciences médicales, Hamadan, Iran
| | - Sara Alijani
- Département d'orthodontie, faculté dentaire, université de sciences médicales, Hamadan, Iran
| | - Fatemeh Azizi
- Département d'orthodontie, faculté dentaire, université de sciences médicales, Kermanshah, Iran.
| |
Collapse
|
26
|
Clinical comparison of two initial arch wires (A-NiTi and Heat Activated NiTi) for amount of tooth alignment and perception of pain: A randomized clinical trial. Int Orthod 2018; 16:60-72. [PMID: 29478933 DOI: 10.1016/j.ortho.2018.01.007] [Citation(s) in RCA: 4] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/22/2022]
Abstract
OBJECTIVES The aim of this study was to compare two initial arch wires, 0.014″ A-NiTi and 0.016″ Heat Activated NiTi (HANT), for amount of tooth alignment and perception of pain. MATERIALS AND METHODS In total, 59 orthodontic patients (21 males and 38 females) from three orthodontic clinics participated in this 2-arm, parallel-group clinical trial and were randomized to 0.014″ A-NiTi (n=30) or 0.016″ HANT groups (n=29). Patient recruitment commenced in April 2016 and ended in December 2016. Age of the patients was between 12 to 25 years with an average of 17.92±3.74 years. Eligibility criteria included permanent dentition, non-extraction treatment plan in lower arch, Irregularity Index>2 in lower arch, no systemic disease influencing pain, no chronic Non Steroid Anti Inflammatory Drug (NSAID) therapy, and no history of dental pain, mucosal ulcers or temporomandibular disorders (TMD). Blinding was applicable to the patients and outcome assessment. The primary outcome was to compare the reduction of the Irregularity Index mean from bonding sessions to 4 weeks later in these groups and the secondary outcome was evaluation of the pain according to the modified McGill Pain Questionnaire (MPQ) with Visual Analogue Scale questionnaire (VAS). RESULTS The mean differences of irregularity indices between the two groups are not statistically significant (95% CI: 0.39-1.03; P=0.36) and according to the questionnaire, there was no significant difference between the two groups in trigger, site, description, duration, beginning, medication, and pain reduction over time. However, the VAS scale of HANT group was significantly higher than that of A-NiTi (P=0.04). CONCLUSION Results from this investigation suggested that there was no clinical difference in amount of tooth alignment and perception of pain between 0.014″ A-NiTi and 0.016″ HANT wires.
Collapse
|