Effectiveness of Different Application Modalities on the Bond Performance of Four Polymeric Adhesive Systems to Dentin

One of the major goals of adhesive dentistry is to improve the interaction of the already-existing adhesives with different substrates by using different application techniques. Thus, the objective of the present in vitro study was to assess the bond performance of four adhesive systems, Prime&Bond Universal (PBU), Clearfil SE Bond (CSE), OptiBond Universal (OBU), and OptiBond FL (OBFL), to dentin using various application modes: passive application (PA), active application (AA), Compo-Vibes modified application (CVM), and Compo-Vibes application (CV). Eighty extracted human molars were allocated into four groups based on the application modalities tested. The micro-tensile bond strength as well as fracture mode were tested in accordance with ISO/TS 11.405 after 24 h and 6 months of aging. Adhesive contact angle (CA) and scanning electron microscope analysis were also performed (n = 3). Statistical tests were performed with α = 0.05. After 24 h, a significant difference with a higher bond strength value was found for PBU in the AA modality and for CSE in the CVM modality (p < 0.05). However, no significant difference was shown between the techniques used among the other adhesives (OBFL and OBU). Moreover, at 24 h, only the PA demonstrated significant differences between the tested materials (p < 0.05). After 6 months, CSE, PBU, and OBU demonstrated significant differences between the techniques (p < 0.05), with a higher bond strength for CSE in AA and CVM modalities, for PBU in AA modality, and for OBU in AA and PA modalities. No significant differences were found between the techniques used among the OBFL (p > 0.05). In addition, only the CVM technique demonstrated significant differences between the tested materials after 6 months. CV and CVM showed a decreased value after aging for CSE and PBU, respectively. However, all the modalities decreased for OBU and OBFL after aging. All the adhesives showed marked resin infiltration into dentinal tubules in AA among all the modalities tested. Both universal adhesive systems (OBU and PBU) demonstrated statistically lower CA when compared to the other systems (CSE and OBFL) (p < 0.05) when applied in the PA mode. Concerning the AA mode, only CSE and OBFL were tested. The AA demonstrated lower CA values compared to the same adhesives in PA (p < 0.05). It could be concluded that the bond strength could be influenced by both materials and application techniques. It seems that the AA technique could be recommended as a gold standard for the application of an adhesive system to dentin. Plus, the CV and CVM modalities after 6 months of aging were considered stable for PBU and CSE, respectively. Consequently, the performance of these adhesive systems might vary when applied to other modalities. Future studies are needed to test this hypothesis.

The Use of Warm Air for Solvent Evaporation in Adhesive Dentistry: A Meta-Analysis of In Vitro Studies

Any excess solvent from dental adhesive systems must be eliminated prior to material photopolymerization. For this purpose, numerous approaches have been proposed, including the use of a warm air stream. This study aimed to investigate the effect of different temperatures of warm air blowing used for solvent evaporation on the bond strength of resin-based materials to dental and nondental substrates. Two different reviewers screened the literature in diverse electronic databases. In vitro studies recording the effect of warm air blowing to evaporate solvents of adhesive systems on the bond strength of resin-based materials to direct and indirect substrates were included. A total of 6626 articles were retrieved from all databases. From this, 28 articles were included in the qualitative analysis, and 27 remained for the quantitative analysis. The results of the meta-analysis for etch-and-rinse adhesives revealed that the use of warm air for solvent evaporation was statistically significantly higher (p = 0.005). For self-etch adhesives and silane-based materials, this effect was observed too (p < 0.001). The use of a warm air stream for solvent evaporation enhanced the bonding performance of alcohol-/water-based adhesive systems for dentin. This effect seems to be similar when a silane coupling agent is submitted to a heat treatment before the cementation of a glass-based ceramic.

Adhesive sonic agitation improves bonding durability to class-II cavity preparation

The purpose of this study was to evaluate the effect of adhesive sonic agitation on resin-dentin micro-tensile bond strength (µTBS) and interfacial morphology at the gingival wall of class-II cavity preparation. Seventy-two molars with prepared class-II cavities were divided into six groups (n = 12) according to the bonding mode; etch-and-rinse (E&R) or self-etch (SE) and application protocol of the universal adhesive (UA) employed (Clearfil Universal Bond Quick, Kuraray Noritake); following the manufacturer instructions (MI), manual agitation for 20 s (20s), or sonic agitation for 20 s using a modified sonic micro-brush mounted on EndoActivator device, Dentsply Sirona, (sonic). Restored teeth were sectioned into resin-dentin beams and slaps and µTBS was evaluated at 1 week (1w) and after thermocycling (10k). µTBS data were analyzed using the linear mixed-effects modeling with specific contrast (p < 0.05). The resin-dentin interfacial morphology was evaluated using a scanning electron microscope. Adhesive sonic agitation resulted in significantly higher µTBS means in both E&R and SE modes, compared to MI group. The µTBS of MI group showed significant reduction upon aging when applied in SE mode. Sonic agitation was associated with enhanced adhesive infiltration into dentin specially in E&R mode. Sonic agitation of UA using modified sonic micro-brush attached to EndoActivator device significantly improved the resin-dentin µTBS and interfacial morphology at the gingival wall of class-II cavity preparation.

Noncarious cervical lesions: Morphology and progression, prevalence, etiology, pathophysiology, and clinical guidelines for restoration

PURPOSE

To synthesize the literature regarding noncarious cervical lesions (NCCLs) and propose clinical guidelines when lesion restoration is indicated.

MATERIAL AND METHODS

A PubMed search was performed related to NCCL morphology, progression, prevalence, etiology, pathophysiology, and restoration.

RESULTS

NCCLs form as either rounded (saucerlike) depressions with smooth, featureless surfaces that progress mainly in height or as V-shaped indentations that increase in both height and depth. Prevalence ranges from less than 10% to over 90% and increases with age. Common locations are the facial surfaces of maxillary premolars. They have a multifactorial etiology due to personal habits such as excessive horizontal toothbrushing and consumption of acidic foods and drinks. Occlusal factors have been identified as contributing to the prevalence of NCCLs in some studies, whereas other studies indicate there is no relationship. The concept of abfraction has been proposed whereby mechanical stress from occlusal loading plays a role in the development and progression of NCCLs with publications supporting the concept and others indicating it lacks the required clinical documentation. Regardless of the development mechanism, demineralization occurs and they are one of the most common demineralization diseases in the body. Treatment should be managed conservatively through preventive intervention with restorative treatment delayed until it becomes necessary due to factors such as lesion progression, impact on patient's quality of life, sensitivity, poor esthetics, and food collection may necessitate restoration. Composite resins are commonly used to restore NCCLs although other materials such as glass ionomer and resin-modified glass ionomer are also used. Sclerotic dentin does not etch like normal dentin and therefore it has been recommended to texture the dentin surface with a fine rotary diamond instrument to improve restoration retention. Some clinicians use mechanical retention to increase retention. Beveling of enamel is used to increase the bonding area and retention as well as enhance the esthetic result by gradually creating a color change between the restoration and tooth. Both multistep and single-step adhesives have been used. Dentin etching should be increased to 30 seconds due to the sclerotic dentin with the adhesive agent applied using a light scrubbing motion for 20 seconds but without excessive force that induces substantial bending of a disposable applicator. Both flowable and sculptable composite resins have been successfully used with some clinicians applying and polymerizing a layer of flowable composite resin and then adding an external layer of sculptable composite resin to provide enhanced resistance to wear. When caries is present, silver diamine fluoride has been used to arrest the caries rather than restore the lesion.

CONCLUSIONS

Noncarious cervical lesions (NCCLs) form as smooth saucerlike depressions or as V-shaped notches. Prevalence values as high as 90% and as low as 10% have been reported due to habits such as excessive toothbrushing and an acidic diet. Occlusal factors have been proposed as contributing to their presence but it remains controversial. Publications have both supported and challenged the concept of abfraction. They are one of the most common demineralization diseases in the body. Conservative treatment through prevention is recommended with restorative treatment delayed as long as possible. When treatment is needed, composite resins are commonly used with proposed restorative guidelines including texturing the sclerotic dentin, beveling the enamel, potential use of mechanical retention, 30 seconds of acid etching, and use of either multistep or single-step adhesives in conjunction with a light scrubbing motion for 20 seconds without excessive force placed on disposable applicators.

Effect of Different Application Modalities on the Bonding Performance of Adhesive Systems to Dentin: A Systematic Review and Meta-Analysis

Diverse types of dental adhesives exhibit different cytotoxic outcomes on cells in vitro. Currently, no standard adhesive application technique has so far been decisive for clinicians for better durability of resin-dentin bonds of adhesive systems. The purpose of this study was to systematically review the literature to evaluate the bonding performance of adhesive systems to dentin by using different application modalities. The systematic research strategy was conducted by two reviewers among multiple databases: PubMed, Scopus, Web of Science, Embase, and Scielo. In vitro studies reporting the effects of additional steps for the application of adhesive systems on the bond strength to dentin were selected. Meta-analysis was performed using Review Manager Software version 5.3.5 using the random effects model. The methodological quality of each in vitro study was assessed according to the parameters of a previous systematic review. The electronic research through different databases generated a total of 8318 references. After the examination of titles and abstracts, a total of 106 potentially relevant studies accessed the full-text evaluation phase. After full-text examination, 78 publications were included for the qualitative analysis, and 68 studies were included in the meta-analysis. Regarding the etch-and-rinse adhesive systems, the application modalities that improved the overall bond strength were the application of a hydrophobic resin layer (p = 0.005), an extended application time (p < 0.001), an application assisted by an electric current (p < 0.001), a double-layer application (p = 0.05), the agitation technique (p = 0.02), and the active application of the adhesive (p < 0.001). For self-etch adhesive systems, the techniques that improved the overall bond strength were the application of a hydrophobic resin layer (p < 0.001), an extended application time (p = 0.001), an application assisted by an electric current (p < 0.001), a double-layer application (p < 0.001), the agitation technique (p = 0.01), and the active application of the adhesive (p < 0.001). The in vitro evidence suggests that the application of adhesive systems using alternative techniques or additional strategies may be beneficial for improving their bond strength to dentin. The application modalities that favored the overall bond strength to dentin were an extended application time, a double-layer application, an application assisted by an electric current, the active application of the adhesive, and the application of a hydrophobic resin layer. Worth mentioning is that some techniques are intended to increase the degree of the conversion of the materials, and therefore, improvements in the biocompatibility of the materials can be expected.

Microtensile bond strength of resin composite to dentin using different adhesive systems and directions of electric current

Thisstudy aimed to evaluate the effect of the electric current direction application on the resin composite-dentin bond strength using three adhesive systems. Human molar teeth were distributed according to the adhesive system (two-step self-etch - Clearfil SE Bond, Kuraray [CSE]; one-step self-etch - Single Bond Universal, 3M ESPE [SBU]; and two-step etch-and-rinse - Adper Single Bond 2, 3M ESPE [SB2]), electric current direction (without electric current - control, direct and reverse electric currents - 35µA), and storage time (24h - immediate and 6 months). Resin composite blocks (Filtek Z350XT, 3M ESPE) were bonded to dentin. The teeth/resin composites specimens were stored in distilled water at 37ºC for 24 hours and 6 months for the microtensile bond strength (µTBS) test (n = 10; ~12 sticks for each tooth). Failure patterns were analyzed on a stereomicroscope and classified as cohesive-dentin, cohesive-resin, adhesive or mixed. Adhesive penetration into dentin and hybrid layer formation were evaluated in a scanning electron microscope (n = 6). Data were submitted to a three-way ANOVA followed by Tukey's post hoc test (α = 0.05). There are no differences in µTBS when the adhesive systems were applied under direct and reverse electric currents, but both electric currents increased the µTBS for all adhesive systems. SBU showed the lowest µTBS values for control groups in both storage times and direct electric current in 6 months of storage. The adhesive failure pattern was more frequently observed in all groups. The electric current formed long resin tags for all adhesive systems. Storage for 6 months did not significantly decrease µTBS values. Both directions of electric current (positive and negative charges) at 35µA can increase the µTBS of the adhesive systems tested to dentin.

Sonic application of one-step self-etch adhesive in composite restorations of non-carious cervical lesions: A double-blind randomized clinical trial

OBJECTIVES

To evaluate the influence of the sonic device on the clinical performance of one-step self-etch adhesive systems in non-carious cervical lesions (NCCLs) after 18 months.

MATERIALS AND METHODS

Forty patients participated in this study. Eighty restorations were assigned to two groups (n = 40): Sonic application and Manual application. After the adhesive application (iBond Self-Etch, Kulzer, Hanau, Germany), NCCLs were restored using composite resin (Charisma, Kulzer, Hanau, Germany). The restorations were evaluated at baseline and after 18 months both according to the Word Dental Federation (FDI) and the United States Public Health Service (USPHS) criteria. Friedman repeated measures analysis of variance by rank and Wilcoxon test for significance in each pair were applied (α = 0.05).

RESULTS

After 18 months, 38 patients were evaluated. Twenty-three restorations were lost (19 for manual vs. 4 for sonic application). The retention rates (95% confidence interval) were 50% (CI 34.8%-65.1%) for manual application and 84.2% (CI 69.6%-92.6%) for sonic application (p < 0.05). Twelve restorations showed marginal staining (nine for manual vs. three for sonic application; FDI, p < 0.05) and nine some marginal discrepancy (seven for manual vs. two for sonic application; FDI, p < 0.05). No restorations showed postoperative sensitivity and caries recurrence at the time.

CONCLUSION

The sonic application increases the retention rate of iBond Self-Etch after 18 months of clinical evaluation in NCCLs.

CLINICAL RELEVANCE

The application of a simplified self-etch adhesive (iBond Self-Etch) associated to a sonic device seems to be an alternative to improve the clinical behavior in NCCLs.

Is the presence of 10-MDP associated to higher bonding performance for self-etching adhesive systems? A meta-analysis of in vitro studies

OBJECTIVE

The purpose of this systematic review and meta-analysis was to analyze the literature on the bond strength of self-etching (SE) adhesives containing 10-MDP or other acidic functional monomers, comparing the bonding performance of both compositions.

METHODS

This study is registered in PROSPERO (CRD42020175715) and it followed the PRISMA Statement. The literature search was performed in PubMed, Web of Science, SciELO, Scopus, LILACS, IBECS, and BBO from the starting coverage date through 30 June 2021. Study eligibility criteria consisted of in vitro studies that evaluated the bond strength (microtensile, microshear, tensile or shear testing) to sound dentin/enamel of a minimum of two distinct SE systems, with at least one material containing 10-MDP and one other being comprised of a distinct acidic composition. Statistical analyses were carried out with RevMan 5.3.5 and using random-effects models with the significance level at p < 0.05. Also, Bayesian network meta-analysis (NMA) was conducted using MetaInsight V3 tool.

RESULTS

From 740 relevant studies evaluated in full-text analysis, 210 were incorporated to the systematic review and 206 in meta-analysis. The majority of studies was classified as having medium risk of bias (56.7%), followed by low (35.2%) and high (8.1%) risk of bias. Data from a total of 64 adhesive systems were collected, which favored the 10-MDP-based group at both dentin (overall effect: 6.98; 95% CI: 5.61, 8.36; p < 0.00001) and enamel (overall effect: 2.79; 95% CI: 1.62, 3.96; p < 0.00001) substrates. Microtensile testing was more frequently used (73.4%) in the included studies. Adhesives based on 10-MDP showed greater bonding performance than adhesives comprised of monomers such as PENTA, 6-MHP, 4-META, 4-MET, pyrophosphate esters, mixed composition or monomers derived from sulfonic acid (p ≤ 0.01); whereas similar bond strength values were verified between 10-MDP-based materials and those containing PEM-F, acrylamide phosphates, 4-AET, MAC-10, or monomers derived from polyacrylic and phosphonic acids (p ≥ 0.05). Adhesives based on GPDM were the only ones that resulted in greater bonding potential than the 10-MDP-based group (p = 0.03). Dental bonds in dentin were favored with the application of 2-step 10-MDP-based adhesives; whereas in enamel the dental bonds were favored for both 2-steps versions of adhesives, regardless of the presence of 10-MDP. Indirect evidence from NMA revealed that 1-step 10-MDP-free and universal 10-MDP-free adhesives seemed to perform worst in dentin and enamel, respectively.

SIGNIFICANCE

Adhesives containing 10-MDP showed higher bonding performance than materials formulated with other acidic ingredients, although this result relied on the type of mechanical testing, type of the substrate, acidic composition of the adhesive, and the application category of the SE system. This review summarized the effects of the foregoing factors on the adhesion to dental substrates.

Influence of acidic monomer concentration and application mode on the bond strength of experimental adhesives

The aim of this research was to evaluate the influence of MDP (10-methacryloyloxydecyl dihydrogen phosphate) concentration and application mode of experimental adhesives on microshear bond strength (μSBS) to dentin after storage in distilled water at 37°C for 24h and 6 months. Five experimental adhesives were prepared with: CQ, DABE, BHT, ethanol, HEMA, TEGDMA, Bis-EMA, UDMA, and Bis-GMA. Concentrations of 0 wt%, 3 wt%, 9 wt%, 12 wt% or 15 wt% of MDP were added to their composition. The adhesives were applied to flat dentin surfaces in etch-and-rinse or self-etching modes. Cylindrical molds filled with light-cured composite resin were placed above the dentin. The specimens were stored in distilled water at 37oC for 24h or 6 months and submitted to μSBS testing. The adhesives were also submitted to pH analysis. The data were analyzed by one-way ANOVA, three-way ANOVA and Tukey's test (α = 5%). All the adhesives used in the etch-and-rinse mode showed significantly higher bond strength than the adhesives applied in the self-etching approach. The 9 wt% adhesive showed the highest bond strength values, and 3 wt% was most stable after storage. A strong negative correlation between MDP concentration and pH was observed. It was concluded that the formulations with low concentrations of MDP (up to 9 wt%) showed better results for bond strength and bond strength degradation over time.

Microshear Bond Strength of Different Adhesive Systems to Dentin

Objectives:

The aim of this study was to compare the microshear bond strength (μSBS) of various adhesive systems to dentin.

Materials and Methods:

In this in vitro experimental study, 60 sound human third molars were divided into four groups. Dentin discs were prepared of middle-third dentin measuring 4 mm in diameter and 2 mm in thickness. Dentin surfaces were bonded with one of the four types of adhesives: (A) Single Bond (3M ESPE), Scotchbond Universal (3M ESPE) in etch and rinse (B) and self-etch (C) modes and (D) Clearfil SE Bond (Kuraray Noritake Dental). After the application of adhesive systems according to the manufacturers’ instructions, composite cylinders (Vit-l-escence) were bonded to dentin surfaces. The μSBS test was performed using a universal testing machine at a crosshead speed of 1 mm/min. Data were analyzed with one-way ANOVA and Tukey’s test (α=0.05).

Results:

The μSBS was the highest in self-etch Scotchbond Universal (15.8±6.08 MPa) followed by Clearfil SE Bond (15.24±4.6 MPa), etch and rinse Scotchbond Universal (11.68±4.07MPa) and Single Bond (11.24±3.74 MPa). A significant difference was only found between Single Bond and etch and rinse Scotchbond Universal groups (P=0.04).

Conclusion:

Based on the results of this study, application of Scotchbond Universal in self-etch mode provides a reliable bond to dentin.

Knoop Hardness of Self-Etch Adhesives Applied on Superficial and Deep Dentin

Statement of the Problem

Low pH of self-etch adhesives might cause suboptimal polymerization.

Purpose

This study aimed to evaluate the effect of dentin depth (deep and superficial) on polymerization efficacy of two self-etch adhesives, with different pH by means of Knoop hardness test.

Materials and Method

In this in vitro study, sixty sound molars were used to prepare 30 superficial dentin and 30 deep dentin specimens. Dentin specimens of each depth were randomly distributed into two equal subgroups (N=15) and bonded by either Adper Prompt L-Pop (strong self-etch adhesive) or Adper Easy Bond (mild self-etch adhesive). Knoop hardness test was employed to evaluate degree of cross-linking of the adhesives. Data were analyzed with SPSS 16, using two-way ANOVA to compare mean hardness values of the study groups (p< 0.05).

Results

There was no interaction effect between dentin depth and the type of adhesive (p= 0.36). Regardless of dentin depth, hardness of Adper Easy Bond was significantly higher than that of Adper Prompt L-pop (p< 0.001). Moreover, both the adhesives showed higher hardness when bonded to superficial dentin compared to deep dentin (p< 0.001).

Conclusion

Degree of cross-linking of the self-etch adhesive with mild acidity was more than that of the strong self-etch adhesive after light-curing. Surface hardness of both adhesives was higher on superficial dentin compared to deep dentin.

Effect of Active Application on Bond Durability of Universal Adhesives

The purpose of this study was to determine the effect of different adhesive application methods and etching modes on the dentin bond durability of universal adhesives under thermal cycling (TC). All-Bond Universal (Bisco), Adhese Universal (Ivoclar Vivadent), and Scotchbond Universal (3M ESPE) were used as adhesives. In total, 600 bovine teeth with exposed dentin were divided into 12 groups according to the type of adhesive and subjected to the following bonding procedures: 1) etch-and-rinse mode with active application; 2) etch-and-rinse mode with inactive application; 3) self-etch mode with active application; and 4) self-etch mode with inactive application. Bonded specimens were stored in distilled water at 37°C for 24 hours and then subjected to 5000, 10,000, 30,000, or 50,000 TC between 5°C and 55°C before shear bond strength (SBS) testing, creating a division into a total of five different storage conditions. Baseline specimens were stored in distilled water at 37°C for 24 hours. The SBS test was performed at a cross-head speed of 1.0 mm/min. Three-way analysis of variance revealed that all the factors of application mode, adhesive, and thermal cycle period significantly influenced the SBS values (p&lt;0.001), regardless of the etching mode. In the baseline groups, all of the tested adhesives with active application had higher SBS values than those with inactive application, regardless of etching mode. In the TC groups, significantly lower SBS values were observed at 50,000 TC with inactive application compared to those with active application, regardless of the etching mode. From the scanning electron microscopy observation of demineralized and deproteinized resin/dentin interfaces, dense resin tags longer than 50 μm were observed in the etch-and-rinse with active application group. On the other hand, the resin tags in self-etch mode were sparse, thin, and much shorter than those in etch-and-rinse mode. Comparing the penetration status of the resin tags with active and inactive application in self-etch mode, the resin tag penetration with inactive application was much lower than that with active application. Active application is effective in enhancing the dentin bond durability of universal adhesives. When using universal adhesives with different etching modes, practitioners should select the optimal etching mode and appropriate application method in accordance with the cavity conditions.

Effect of various agitation methods on adhesive layer formation of HEMA-free universal dentin adhesive

This study evaluates the effects of various agitation methods on the adhesive layer formation of a new HEMA-free universal dentin adhesive. The µTBS of the universal adhesive, G-Premio BOND in the self-etch mode was evaluated using three agitation methods [passive agitation (PA), active agitation (AA), ultrasonic agitation (UA)], with and without aging treatment. Two-way analysis of variance revealed that aging treatment was not a statistically significant factor. Tukey's HSD test showed significant differences based on the application method, UA>AA>PA. TEM images of the PA group revealed multiple water blisters in the adhesive layers; AA and UA groups presented significantly less or no blisters within the adhesive layers; thus, AA and UA groups exhibited better bonding performance for the HEMA-free universal adhesive. It is assumed that the entrap ped blisters can be reduced with the active application of dentin adhesive, and thus improving the bonding performance.

Clinical Effectiveness of a Resin-modified Glass Ionomer Cement and a Mild One-step Self-etch Adhesive Applied Actively and Passively in Noncarious Cervical Lesions: An 18-Month Clinical Trial

OBJECTIVES:

To evaluate the clinical effectiveness of two methods of application of a mild one-step self-etch adhesive and composite resin as compared with a resin-modified glass ionomer cement (RMGIC) control restoration in noncarious cervical lesions (NCCLs).

METHODS:

A total of 294 restorations were placed in 56 patients, 98 in each one of the following groups: 1) G-Bond active application combined with Solare-X composite resin (A-1SEA), 2) G-Bond passive application combined with Solare-X composite resin (P-1SEA), and 3) GC II LC RMGIC. The restorations were evaluated at baseline and after six, 12, and 18 months according to the FDI criteria for fractures/retention, marginal adaptation, marginal staining, postoperative sensitivity, and secondary caries. Cumulative failure rates were calculated for each criterion at each recall period. The effect of adhesive, method of application, and recall period were assessed. The Kruskal-Wallis test for intergroup comparison and Friedman and Wilcoxon signed ranks tests for intragroup comparison were used for each criterion ( α=0.05).

RESULTS:

The retention rates at 18 months were 93.26% for the A-1SEA group, 86.21% for the P-1SEA group, and 90.91% for the RMGIC group. The active application improved the retention rates compared with the passive application of mild one-step self-etch adhesive; however, no statistically significant difference was observed between the groups. Marginal staining was observed in 13 restorations (1 in A-1SEA, 4 in P-1SEA, and 8 in RMGIC) with no significant difference between the groups. The RMGIC group showed a significant increase in marginal staining at 12 and 18 months from the baseline. There was no significant difference between the groups for marginal adaptation, secondary caries, or postoperative sensitivity.

CONCLUSION:

Within the limitations of the study, we can conclude that mild one-step self-etch adhesive followed by a resin composite restoration can be an alternative to RMGIC with similar retention and improved esthetics in restoration of NCCLs. Agitation could possibly benefit the clinical performance of mild one-step self-etch adhesives, but this study did not confirm that the observed benefit was statistically significant.

Influence of Surface Treatment on Composite Adhesion in Noncarious Cervical Lesions: Systematic Review and Meta-analysis

The purpose of this study was to analyze the influence of dentin surface treatments on the retention rate of resin composite restorations in non-carious cervical lesions (NCCLs). Seven randomized clinical trials were included in this review. Data regarding retention rate, type of surface treatment, and the main characteristics of studies were analyzed. Two reviewers performed a literature search up to December 2016 in eight databases: PubMed (Medline), Lilacs, Ibecs, Web of Science, BBO, Scopus, Scielo and The Cochrane Library. Only clinical trials evaluating dentin surface treatments in resin composite restoration in NCCLs were included. Noncontrolled clinical trials, reviews, editorial letters, case reports, case series and studies published in a language other than English, Portuguese, or Spanish were not included. The included studies evaluated different surface treatments, such as using an adhesive system with a frictional technique, drying the dentin, and removing sclerotic dentin by using a bur and applying EDTA before primer use. The analysis considering the mechanical removal of dentin surface with a bur and the application of an adhesive system in a frictional mode showed these treatments improved retention rates of the resin composite restorations in NCCLs ( p<0.05). There is evidence in the literature suggesting that the mechanical removal of dentin surface with a bur and the application of an adhesive system in a frictional mode could improve the retention rates of resin composite restorations in NCCLs. However, the studies showed high heterogeneity, and additional clinical trials are needed to determine the best dentin treatment option in NCCLs.

Effect of rubbing force magnitude on bond strength of universal adhesives applied in self-etch mode

This study investigated the effect of rubbing force magnitude on dentin bond strengths of multi-mode adhesives applied in self-etch mode. Seventy-two extracted human molar teeth were used. Two different universal adhesives Single Bond Universal (SB) and Clearfil Universal (CL) were applied onto dentin surfaces in three different modes: without rubbing (NR), rubbing with 40 gf (gram-force) (40) or 80 gf (80) load. Teeth were restored with a resin composite. Half of the specimens were subject to thermal aging (10,000 cycles). Microtensile bond strength was measured and data were statistically analyzed with two-way analysis of variance and Tukey's test (α=0.05). Baseline bond strength values for CL adhesive were improved by rubbing (40 and 80 gf) as compared to no rubbing (p<0.05). Rubbing did not significantly improve bond strength values for SB, regardless of aging (p>0.05). Rubbing improves bonding performance of some universal adhesives to dentin when applied in self-etch mode.

Assessment of resin-dentin interfacial morphology of two ethanol-based universal adhesives: A scanning electron microscopy study

OBJECTIVE

The objective of this study was to assess the resin-dentin interfacial morphology created by two universal adhesives using scanning electron microscopy (SEM).

MATERIALS AND METHODS

The occlusal surfaces of ten (n = 5) molars were reduced to expose a flat surface of dentin. Two universal adhesives, Scotchbond Universal Adhesive and Tetric N-Bond Universal, were independently applied to air-dried dentin. Light-cured resin-based composite restorative materials were used to incrementally build a composite "buildup." The specimen was sectioned mesiodistally to expose the resin-dentin interface. The inner surfaces of the specimens were polished. Samples were immersed in hydrochloric acid and then rinsed using distilled water. This was followed by immersion of the samples in 1% sodium hypochlorite solution. Then, samples were thoroughly rinsing with distilled water. Dehydration of samples was performed using ascending concentration of ethyl alcohol. Prepared samples were observed SEM at magnifications ×1500 and x4000.

RESULTS

Both universal adhesives could penetrate dentin-forming well-defined resin tags, lateral branches as well as a uniform hybrid layer.

CONCLUSIONS

Two tested universal adhesives applied in self-etch mode can infiltrate into dentin-producing high-quality interfacial morphology. Similar interfacial morphology may be due to the similarity in composition and application mode.

Marginal microleakage in Bulk Fill resins

Abstract Introduction Despite advances and innovations in restorative dentistry, microleakage remains one of the main problems in this area. Objective To evaluate in vitro marginal microleakage of Bulk Fill resins in class II cavities, with cervical termination in the dentin. Material and method Cavities, standardized on the mesial and distal surfaces, were prepared in forty top molars and randomly assigned to four groups (n = 10), according to the resin used. G1 (control): Filtek Z350 (3M/ESPE); G2: Filtek Bulk Fill flow (3M/ESPE); G3: Surefill SDR (Dentsply); G4: X-tra (Voco). These were further subdivided into subgroups according to the strategy used to apply the adhesive (self-etch technique and conventional). After storage for 24 hours in an oven (37 °C), the samples were submitted to the thermocycling test (500 cycles: 5 °C/55 °C). They were later waterproofed, immersed in Basic Fuchsin (0.5%) and sectioned in the mesial-distal direction for evaluation using a stereo magnifying glass at 40X (Coleman) Scores from 0 to 3 were assigned according to the microinfiltration observed. The Mann-Whitney and Kruskal-Wallis tests, with a significance level of 5%, were used for statistical analysis. Result There was no statistically significant difference between the Bulk Fill resins when the total acid-etching technique was used. Only the Filtek Bulk fill flow resin presented statistically significant results when the application of the adhesive system strategy was considered, with worse results, in relation to other groups, when it the self-etching strategy was considered. Conclusion The degree of leakage of the bulk fill resins studied, in class II cavities, was not influenced by the method of application of the adhesive system (conventional or two-step self-etching bonding agent), except for the Filtek Bulk fill flow.

Influence of duration of phosphoric acid pre-etching on bond durability of universal adhesives and surface free-energy characteristics of enamel

The purpose of this study was to evaluate the influence of duration of phosphoric acid pre-etching on the bond durability of universal adhesives and the surface free-energy characteristics of enamel. Three universal adhesives and extracted human molars were used. Two no-pre-etching groups were prepared: ground enamel; and enamel after ultrasonic cleaning with distilled water for 30 s to remove the smear layer. Four pre-etching groups were prepared: enamel pre-etched with phosphoric acid for 3, 5, 10, and 15 s. Shear bond strength (SBS) values of universal adhesive after no thermal cycling and after 30,000 or 60,000 thermal cycles, and surface free-energy values of enamel surfaces, calculated from contact angle measurements, were determined. The specimens that had been pre-etched showed significantly higher SBS and surface free-energy values than the specimens that had not been pre-etched, regardless of the aging condition and adhesive type. The SBS and surface free-energy values did not increase for pre-etching times of longer than 3 s. There were no significant differences in SBS values and surface free-energy characteristics between the specimens with and without a smear layer. The results of this study suggest that phosphoric acid pre-etching of enamel improves the bond durability of universal adhesives and the surface free-energy characteristics of enamel, but these bonding properties do not increase for phosphoric acid pre-etching times of longer than 3 s.

Effect of Er,Cr:YSGG Laser at Different Output Powers on the Micromorphology and the Bond Property of Non-Carious Sclerotic Dentin to Resin Composites

BACKGROUND

The objective of this study was to investigate the influence of Er,Cr:YSGG laser irradiated at different powers on the micromorphology and the bonding property of non-carious sclerotic dentin to resin composites.

METHODS

Two hundred bovine incisors characterized by non-carious sclerotic dentin were selected, and the seventy-two teeth of which for surface morphological analysis were divided into nine groups according to various treatments (A: the control group, B: only treated with the adhesive Adper Easy One, C: diamond bur polishing followed by Adper Easy One, D-I: Er,Cr:YSGG laser irradiating at 1W, 2W, 3W, 4W, 5W, 6W output power, respectively, followed by Adper Easy One). The surface roughness values were measured by the non-contact three-dimensional morphology scanner, then the surface micromorphologies of surfaces in all groups were assessed by scanning electron microscopy (SEM); meanwhile, Image Pro-Plus 6.0 software was used to measure the relative percentage of open tubules on SEM images. The rest, one hundred twenty-eight teeth for bond strength test, were divided into eight groups according to the different treatments (A: only treated with the adhesive Adper Easy One, B: diamond bur polishing followed by the above adhesive, C-H: Er,Cr:YSGG laser irradiating at 1 W, 2 W, 3 W, 4 W, 5 W, 6 W output power, respectively, followed by the above adhesive), and each group was subsequently divided into two subgroups according to whether aging is performed (immediately tested and after thermocycling). Micro-shear bond strength test was used to evaluate the bond strength.

RESULTS

The 4W laser group showed the highest roughness value (30.84±1.93μm), which was statistically higher than the control group and the diamond bur groups (p<0.05). The mean percentages ((27.8±1.8)%, (28.0±2.2)%, (30.0±1.9)%) of open tubules area in the 4W, 5W, 6W group were higher than other groups (p<0.05). The 4W laser group showed the highest micro-shear bond strength not only in immediately tested (17.60±2.55 PMa) but after thermocycling (14.35±2.08MPa).

CONCLUSION

The Er,Cr:YSGG laser at 4W power can effectively improve the bonding property between non-carious sclerotic dentin and resin composites by increasing the roughness and mean percentage area of open tubules.

Influence of Organic Acids from the Oral Biofilm on the Bond Strength of Self-Etch Adhesives to Dentin

Abstract: The aim of this study was to evaluate the microtensile bond strength of self-etch adhesive systems to dentin after storage in acids from oral biofilm. Three adhesive systems were used in the study: a two-step self-etch adhesive for use with a silorane-based resin composite (Filtek P90 adhesive system - P90), a two-step self-etch adhesive (Clearfil SE Bond - CSE) and a one-step self-etch adhesive (Adper Easy One - AEO). The bond strength of these products was evaluated by bonding resin composite (Filtek Z350 for CSE and AEO; and Filtek P90 for P90) to 90 bovine dentin tooth fragments, according to the manufacturer's instructions. After 24 h of water storage at 37 °C, the specimens were sectioned into beams (1 mm2) divided and stored in distilled water, lactic acid and propionic acid, for 7 and 30 days. After storage, the specimens were tested for microtensile bond strength. Data were analyzed by three-way ANOVA and Tukey´s test (α=0.05). CSE presented the highest microtensile bond strength after storage in distilled water for 7 and 30 days. The microtensile bond strength of all adhesive systems was lower after storage in lactic acid and propionic acid than after water storage. Significant difference was not found between storage times.

Effect of agitation and storage temperature on water sorption and solubility of adhesive systems

The purpose of this study was to evaluate the influence of storage temperature and flask agitation on the water sorption (WS) and solubility (SL) of simplified adhesive systems. Seventy-two disc-shaped specimens were prepared according to the adhesive system (water/ethanol-based: Adper Single Bond 2; and water-based: One Coat Bond SL) and experimental conditions tested (mechanical agitation and storage temperature). Statistical analysis (3-way ANOVA, alpha=5%) found significantly greater WS and SL means for the water/ethanol-based system when compared to the water-based. Irrespective of factors studied, significant differences in WS and SL were noted between cold and room temperatures, with greater values been obtained at 1°C, and lower ones at 20°C. Agitation provided increased WS for both materials at all temperatures, but did not affect their SL. The mechanical agitation of the flask may negatively affect the dynamics of diffusion of simplified adhesive systems, even at extremely cold or warm temperatures.

Clinical Performance of One-step Self-etch Adhesives Applied Actively in Cervical Lesions: 24-month Clinical Trial

Objectives

To evaluate the clinical performance of two one-step self-etch adhesives in noncarious cervical lesions (NCCL) under active or passive application mode.

Methods

Thirty-one patients with four NCCL were enrolled in this study. One hundred and twenty-four restorations were placed according to one of the following conditions: 1) Adper Prompt L-Pop (AP), active application (APA); 2) AP, passive application (APP); 3) Xeno III (XE), active application (XEA), or 4) XE, passive application (XEP). The restorations were evaluated by the FDI World Dental Federation criteria at baseline and after six, 12, and 24 months of clinical service. The effects of adhesive, mode of application, and recall period were assessed via mixed generalized linear model (α=0.05).

Results

The adhesive AP and the passive application mode showed significantly higher marginal staining than did XE and active application, respectively (p&lt;0.05). With regard to the retention rates, the active application mode yielded higher retention rates at the 24-month recall compared to the passive application, regardless of the material. The individual retention rates (95% confidence interval) of both adhesives in the active application mode were the same, 96.8% (83.8-99.4%), while in the passive application rates were 87.1% (71.2-94.9%) and 80.7% (63.7-90.8%) for XE and AP, respectively.

Conclusions

The active application improved the retention rates of both adhesives after 24 months and minimized the marginal staining at enamel margins.

Effect of blood contamination and decontamination protocols on acetone-based and ethanol-based total etch adhesive systems

STATEMENT OF THE PROBLEM

The efficacy of various decontamination protocols to reverse the effect of blood contamination after acid-etching may depend on the type of adhesive.

OBJECTIVES

To compare the effect of blood contamination and various decontamination protocols on acetone-based and ethanol-based total-etch adhesive systems.

METHODS

Occlusal dentin of 64 human molars was etched and contaminated with fresh human blood. The samples were assigned to two groups as per adhesive used: Prime & Bond NT (acetone-based) and Adper Single Bond 2 (ethanol-based) and then subdivided into eight groups: (1) control, (2) no decontamination, (3) water rinsing, (4) re-etching, (5) sodium hypochlorite, (6) sodium hypochlorite/sodium ascorbate, (7) hydrogen peroxide, and (8) ethanol. Adhesives were applied and specimens were prepared for μTBS after composite buildup. The data were subjected to analysis of variance followed by post hoc Tukey test.

RESULTS

Blood contamination significantly reduced μTBS of both the adhesives. Re-etching and NaOCl/Asc were effective in restoring μTBS to the level of control for both the adhesives whereas NaOCl was effective only for Prime & Bond NT.

CONCLUSION

Both re-etching and NaOCl can be used for regaining μTBS of blood-contaminated acid-etched dentin. NaOCl/Asc yields better results than NaOCl alone, specifically for ethanol-based adhesive.

CLINICAL SIGNIFICANCE

Knowing the adverse effects of prolonged acid-etching, other alternatives for decontamination of etched dentin after blood contamination should be considered. NaOCl alone or NaOCl followed by sodium ascorbate may prove to be good alternatives. These choices also may determine the type of adhesive system.

Effect of the application time of phosphoric acid and self-etch adhesive systems to sclerotic dentin

Objectives:

To evaluate the effect of application time on the resin-dentin bond strength (µTBS) and etching pattern of adhesive systems applied on sclerotic dentine.

Material and Methods:

A total of forty-two bovine incisors had their roots removed. The 1-step self-etch GO (SDI), the 2-step self-etch Adper SE Bond (3MESPE) and the 35% phosphoric acid (3MESPE) from the 2-step etch-and-rinse Adper Single Bond 2 (3MESPE) were applied on the bovine incisal surfaces according to the manufacturer's instructions or duplicating the recommended conditioning time. After adhesive application, thirty teeth were restored with composite resin, stored for 24 h in distilled water at 37º C, and sectioned into resin-dentin bonded sticks (0.8 mm²⁾ and tested according to the µTBS at 0.5 mm/min. The etching pattern of the remaining twelve teeth (n=4 for each material) was examined under scanning electron microscopy. Each tooth was divided into a buccal-to-lingual direction into three thirds, and each third randomly assigned to the groups: control (no treatment), according to the manufacturers' instructions and duplicating the recommended application time. The µTBS and the relative percentage of the tubule area opening were evaluated by two-way repeated measures ANOVA and Tukey's tests (α=0.05).

Results:

The duplication of the conditioning time favored only the GO adhesive (p<0.05). Both application methods significantly increased the tubule area opening (p<0.05) compared to the controls.

Conclusions:

The efficacy of duplicating the conditioning time was only effective for the 1-step self-etch adhesive system tested.

Immediate adhesive properties to dentin and enamel of a universal adhesive associated with a hydrophobic resin coat

OBJECTIVES

To evaluate the effect of acid etching and application of a hydrophobic resin coat on the enamel/dentin bond strengths and degree of conversion (DC) within the hybrid layer of a universal adhesive system (G-Bond Plus [GB]).

METHODS

A total of 60 extracted third molars were divided into four groups for bond-strength testing, according to the adhesive strategy: GB applied as a one-step self-etch adhesive (1-stepSE); GB applied as in 1-stepSE followed by one coat of the hydrophobic resin Heliobond (2-stepSE); GB applied as a two-step etch-and-rinse adhesive (2-stepER); GB applied as in 2-stepER followed by one coat of the hydrophobic resin Heliobond (3-stepER). There were 40 teeth used for enamel microshear bond strength (μSBS) and DC; and 20 teeth used for dentin microtensile bond strength (μTBS) and DC. After restorations were constructed, specimens were stored in water (37°C/24 h) and then tested at 0.5 mm/min (μTBS) or 1.0 mm/min (μSBS). Enamel-resin and dentin-resin interfaces from each group were evaluated for DC using micro-Raman spectroscopy. Data were analyzed with two-way analysis of variance for each substrate and the Tukey test (α=0.05).

RESULTS

For enamel, the use of a hydrophobic resin coat resulted in statistically significant higher mean enamel μSBS only for the ER strategy (3-stepER vs 2-stepER, p<0.0002). DC was significantly improved for the SE strategy (p<0.00002). For dentin, the use of a hydrophobic resin coat resulted in significantly higher dentin mean μTBS only for the SE strategy (2-stepSE vs 1-stepSE, p<0.0007). DC was significantly improved in groups 2-stepSE and 3-stepER when compared with 1-stepSE and 2-stepER, respectively (p<0.0009).

CONCLUSIONS

The use of a hydrophobic resin coat may be beneficial for the selective enamel etching technique, because it improves bond strengths to enamel when applied with the ER strategy and to dentin when used with the SE adhesion strategy. The application of a hydrophobic resin coat may improve DC in resin-dentin interfaces formed with either the SE or the ER strategy. On enamel, DC may benefit from the application of a hydrophobic resin coat over 1-stepSE adhesives.

Effect of sonic application mode on the resin-dentin bond strength and nanoleakage of simplified self-etch adhesive

OBJECTIVES

This study aims to evaluate the effect of different application modes on the immediate and 6-month resin-dentin bond strength (μTBS) and nanoleakage in the hybrid and adhesive layers.

MATERIALS AND METHODS

Three 1-step self-etch adhesives (One Coat 7.0 (OC), Clearfil S(3) Bond (CS), and FuturaBond NR (FB)) were applied on a flat superficial dentin surface of 30 human molars under manual mode or sonic vibration at a frequency of 170 Hz (SV). Composite build-ups were constructed incrementally; specimens were sectioned to obtain resin-dentin sticks with cross-sectional area of 0.8 mm(2) and tested in tension (0.5 mm/min) immediately (IM) or after 6 months (6M) of water storage. Two bonded sticks, from each tooth at each storage time, were immersed in a silver nitrate solution, photo-developed, and analyzed under scanning electron microscopy. The amount of nanoleakage was measured using the ImageTool 3.0 software. Data, from each adhesive, were analyzed by two-way ANOVA and Tukey's test (α = 0.05).

RESULTS

OC and CS showed higher μTBS and lower nanoleakage in the IM period when applied with SV groups. For FB, no significant difference was observed between the two modes of application. All materials showed lower nanoleakage in the SV groups. Higher nanoleakage was observed after 6M for OC and FB.

CONCLUSIONS

The sonic application mode at an oscillating frequency of 170 Hz can improve the resin-dentin μTBS, reduce the nanoleakage, and retard the degradation of the resin-dentin μTBS of Clearfil S(3) Bond and One Coat 7.0 adhesives.

CLINICAL SIGNIFICANCE

Sonic application mode at an oscillating frequency of 170 Hz can be helpful and easy to use in dental practice to guaranty long-lasting restorations.

Overview of Clinical Alternatives to Minimize the Degradation of the Resin-dentin Bonds

The incorporation of hydrophilic and acidic resin monomers substantially improved the initial bonding of contemporary etch-and-rinse (ER) and self-etch (SE) adhesives to intrinsically wet dental substrates, providing quite favorable immediate results, regardless of the bonding approach used. However, in the long term, the bonding effectiveness of most simplified ER and SE adhesives drop dramatically. This review examines the fundamental processes that are responsible for the aging mechanisms involved in the degradation of the resin-bonded interfaces and some possible clinical approaches that have been effective in minimizing or even preventing the degradation of the adhesive interfaces produced with simplified adhesives. The incorporation of some of the feasible approaches - described in this review - may improve the quality of the adhesive restorations performed in clinical practice, while manufacturers develop bonding materials that are less susceptible to the aging mechanisms present in the oral environment.

Prolonged curing time reduces the effects of simulated pulpal pressure on the bond strength of one-step self-etch adhesives

The aim of this study was to evaluate the effects of extended light-curing procedures on the microtensile bond strength (μTBS) of one-step self-etch adhesives (1-SEAs) submitted to simulated pulpal pressure. Coronal deep-dentin specimens were bonded using Clearfil S3 Bond (S3), Adper Easy Bond (EB), or G-Bond Plus (GB) following the manufacturers' recommendations and light-cured for 10 seconds or 40 seconds. The dentin-bonded specimens were stored in distilled water for 24 hours without pulpal pressure (control) or submitted to 20 cm H2O simulated pulpal pressure for 24 hours. The specimens were cut into matchsticks and subjected to μTBS testing. The data were statistically analyzed using the three-way analysis of variance and Tukey's tests (p<0.05). Debonded sticks were investigated through scanning electron microscopy. EB obtained higher bond strengths than GB and S3. However, prolonged light activation (40 seconds) provided higher μTBS for all adhesives when submitted to pulpal pressure. Conversely, pulpal pressure caused a drop in μTBS in EB and S3 when light-cured for 10 seconds. A mixed failure mode was mainly attained for the control groups, whereas the specimens submitted to pulpal pressure failed in the adhesive mode. The μTBS of GB was not affected by pulpal pressure when light-cured for 10 seconds. Adhesive was the most prevalent failure mode, except when light-cured for 40 seconds, which showed predominantly cohesive failure. Extended curing times improved the resistance of 1-SEAs to simulated pulpal pressure.

Effect of application mode on interfacial morphology and chemistry between dentine and self-etch adhesives

OBJECTIVE

To investigate the influence of application mode on the interfacial morphology and chemistry between dentine and self-etch adhesives with different aggressiveness.

METHODS

The occlusal one-third of the crown was removed from un-erupted human third molars, followed by abrading with 600 grit SiC under water. Rectangular dentine slabs were prepared by sectioning the tooth specimens perpendicular to the abraded surfaces. The obtained dentine slabs were treated with one of the two one-step self-etch adhesives: Adper Easy Bond (AEB, pH∼2.5) and Adper Prompt L-Pop (APLP, pH∼0.8) with (15s, active application) or without (15s, inactive application) agitation. The dentine slabs were fractured and the exposed adhesive/dentine (A/D) interfaces were examined with micro-Raman spectroscopy and scanning electron microscopy (SEM).

RESULTS

The interfacial morphology, degree of dentine demineralization (DD) and degree of conversion (DC) of the strong self-etch adhesive APLP showed more significant dependence on the application mode than the mild AEB. APLP exhibited inferior bonding at the A/D interface if applied without agitation, evidenced by debonding from the dentine substrate. The DDs and DCs of the APLP with agitation were higher than those of without agitation in the interface, in contrast to the comparable DD and DC values of two AEB specimen groups with different application modes. Raman spectral analysis revealed the important role of chemical interaction between acid monomers of self-etch adhesives and dentine in the above observations.

CONCLUSION

The chemical interaction with dentine is especially important for improving the DC of the strong self-etching adhesive at the A/D interface. Agitation could benefit polymerization efficacy of the strong self-etch adhesive through enhancing the chemical interaction with tooth substrate.

Comparison of microleakage of composite restorations using fifth and sixth generation dentin bonding agent: an in vivo study

INTRODUCTION

The success of bonded restorations depends on effective bonding between restorative materials and tooth structure, and it prevents microleakage. New dentin bonding systems have been introduced which promotes this concept. The aim of this study was to compare the amount of microleakage between 'single bond' vs 'Prompt L-Pop' during different time periods.

MATERIALS AND METHODS

In this clinical trial study, 60 nonretentive class five cavities were prepared on buccal surfaces of human premolars which were scheduled to be removed for orthodontic purposes. The cavities were restored using two different bonding agents; fifth generation (Single Bond) and sixth generation (Prompt L-Pop) and then filled with resin composite (Filtek Z-250). The samples in both groups were extracted after placing the restoration in three periods of time: Immediately, 1 week and 6 months postplacement. Specimens were sealed with two layers of nail varnish except for 1 mm around restoration and immersed in a silver nitrate solution for 24 hours. The teeth were then sectioned longitudinally and the degree of microleakage was determined by stereomicroscope based on standard usual criteria.

RESULTS

Single bond showed more leakage at dentin margin than enamel margin in all three extraction periods and differences were significant among three groups (p < 0.05). In samples which were restored with Prompt L-Pop only in groups of 6 months there were significant differences between enamel and dentin margins. At enamel margin there were no significant differences between microleakage of groups according to the passage of time (p > 0.05).

CONCLUSION

The results of this study using two different bonding systems, indicate that adhesion to enamel was more valuable than dentin and perhaps systems that include self-etching primers are less sensitive to remaining moisture on dentin and they are less affected during different time periods.

Distinct photopolymerization efficacy on dentin of self-etch adhesives

The effect of application mode on polymerization effectiveness of self-etch adhesives with different pHs has rarely been studied. We applied 2 self-etch adhesives-Adper Prompt L-Pop (APLP, pH ~ 0.8) and Adper Easy-Bond (AEB, pH ~ 2.5)-to dentin with or without agitation (dynamic or static application), to investigate photopolymerization efficacy on dentin, and to understand the role of chemical interaction/reaction between adhesives and dentin. Micro-Raman spectra and imaging were acquired across the dentin/adhesive (D/A) interface. The degree of conversion (DC) of each adhesive as a function of position was calculated. SEM-EDS was used to obtain the elemental distribution along the interface. Photopolymerization efficacies of the two self-etch adhesives on dentin were apparently different. APLP exhibited decreasing DCs as the distance from the D/A interface became greater for both application modes, while the DCs for the dynamic mode were much higher than those for the static mode. As for AEB, the DCs remained almost constant across the adhesive layer and showed no significant difference between two modes. Raman spectral analysis disclosed that the chemical interaction between dentin and adhesives was responsible for the observations. We also verified this by tracking the distribution of the elements Ca and P in the adhesive layers.

Effect of multiple coatings of one-step self-etching adhesive on microtensile bond strength to primary dentin

OBJECTIVE

To investigate the effect of multiple coatings of the one-step self-etching adhesive on immediate microtensile bond strength to primary dentin.

METHODS

Twelve caries-free human primary molars were randomly divided into 2 groups with 6 teeth each. In group 1, each tooth was hemisected into two halves. One half was assigned to control subgroup 1, which was bonded with a single-step self-etching adhesive according to the manufacturer's instructions; the other half was assigned to experimental subgroup 1 in which the adhesive was applied three times before light curing. In group 2, the teeth were also hemisected into two halves. One half was assigned to control subgroup 2, which was bonded with the single-step self-etching adhesive according to the manufacturer's instructions; the other half was assigned to experimental subgroup 2 in which three layers of adhesive were applied with light curing each successive layer. Microtensile bond strength was immediately tested after specimen preparation.

RESULTS

When the adhesive was applied three times before light curing, the bond strength of the experimental subgroup 1 (n=33, 57.49 +/-11.61 MPa) was higher than that of the control subgroup 1 (n=31, 49.71 +/-11.43 MPa, P<0.05). When using the technique of applying multiple layers of adhesive with light curing each successive layer, no difference of immediate bond strength was observed between the control subgroup 2 and the experimental subgroup 2 (P>0.05).

CONCLUSION

strength to primary dentin when using the technique of light-curing after applying three layers of adhesive.

Factors affecting the bond strength of self-etch adhesives: A meta-analysis of literature

Aim:

The purpose of this study is to critically evaluate the factors that affect the bond strength of one-step and two-step self-etch adhesives by using meta-analysis.

Materials and Methods:

Potential papers that were selected according to inclusion and exclusion criteria from articles were published in 13 peer-reviewed journals using “PubMed data base”. From each report, means and standard deviations of bond strengths were extracted and tabulated with corresponding experimental conditions.

Results:

All the studied parameters showed no significant difference, except for dentin origin/site and bonding area. In addition, statistical analysis done with ANOVA showed statistical significance between the one-step and two-step self-etch adhesives.

Conclusions:

Our analysis has showed that two-step self-etch adhesive system showed a superior in vitro performance in comparison to one-step self-etch system. Nevertheless, certain factors such as dentin origin, site and area of bonding affect the bond strength of adhesives.

Effect of 3-year water storage on the performance of one-step self-etch adhesives applied actively on dentine

OBJECTIVES

To evaluate the effect of the application method on the immediate and 3-year resin-dentine bond strength (μTBS) and nanoleakage (NL) for 3 one-step self-etch adhesives (Adper Prompt L-Pop; Clearfil S(3) Bond and Xeno III).

METHODS

The occlusal enamel of 42 human molars were removed to expose a flat dentine surface. The adhesives were applied under inactive or active application. After light-curing (600mW/cm(2) for 10s), composite buildups were constructed incrementally and sectioned to obtain bonded sticks (0.8mm(2)) to be tested in tension immediately or after 3 years of water storage of water storage. For NL, 2 bonded sticks from each tooth at each time were coated with nail varnish, placed in silver nitrate and polished down with SiC paper. The μTBS data was submitted to a two-way repetead mesures ANOVA and Tukey's test for each adhesive (α=0.05).

RESULTS

The active application showed higher immediate and 3-year μTBS than the inactive application (p<0.05). An increase in the silver nitrate deposition was seen for all conditions after 3 years; however this was more pronounced for all materials under inactive application (p<0.05).

CONCLUSIONS

The active application improves the immediate bonding performance of the adhesive systems. Reductions of the bond strength were observed for all materials after 3 years, however reduced degradation rate was observed when the materials are applied actively in dentine.