Evaluation of surface microhardness and gingival marginal adaptation of three different bulk-fill flowable resin composites: A comparative study

OBJECTIVES

To evaluate surface microhardness and gingival marginal adaptation of three different bulk-fill flowable resin composites (FB-RBCs) in Class V cavities with enamel or dentin margins before and after thermocycling (TMC).

MATERIALS AND METHODS

Three available FB-RBCs were used; Palfique Bulk Flow (PaBF) (Tokuyama Dental), SDR Flow+ Bulk Fill Flowable (Dentsply Sirona), and I-Flow Bulk Fill (I-Dental). Thirty discs were prepared from each type of FB-RBCs. The discs were subjected to Vickers microhardness tester machine. Class V cavities were prepared on 180 molars. Gingival margins of half the specimens were prepared above CEJ and the other half below CEJ. Cavities were restored with FB-RBCs for gingival marginal adaptation test. Two-way ANOVA was used in microhardness, while three-way ANOVA was used for marginal adaptation.

RESULTS

The used materials showed statistically significant differences in microhardness and marginal adaptation.

CONCLUSIONS

Regarding microhardness, PaBF showed the highest value before TMC and SDR was the highest after TMC. Regarding marginal adaptation, SDR revealed the best marginal adaptation than PaBF and I-flow, either subjected to TMC or not.

CLINICAL SIGNIFICANCE

The longevity of cervical restorations depend on both the location of the cavity margin and the material used. The microfractures in resin composite surface due to low surface microhardness as well as marginal gaps seen in laboratory studies could be considered as an indicative parameter for clinical problem associated with marginal differences.

Minimally invasive CAD/CAM lithium disilicate partial-coverage restorations show superior in-vitro fatigue performance than single crowns

OBJECTIVE

To analyze the influence of restoration design (partial-coverage restoration vs. crown) and ceramic layer thickness on the performance and failure loads of CAD/CAM-fabricated lithium disilicate (LDS) reconstructions on molars after fatigue.

MATERIALS AND METHODS

Seventy-two posterior monolithic CAD/CAM-fabricated LDS restorations (IPS e.max CAD, Ivoclar Vivadent) with different occlusal/buccal ceramic layer thicknesses (1.5/0.8, 1.0/0.6, and 0.5/0.4 mm) and restoration designs (PCR: non-retentive full-veneer/partial-coverage restoration, C: crown,) were investigated and divided into six groups (n = 12, test: PCR-1.5, PCR-1.0, PCR-0.5; control: C-1.5, C-1.0, C-0.5). LDS restorations were adhesively bonded (Variolink Esthetic DC, Ivoclar Vivadent) to dentin-analogue composite dies (Z100, 3M ESPE). All specimens were subjected to thermomechanical loading (1.2 million cycles, 49 N, 1.6 Hz, 5-55°C) and exposed to single load to failure testing. Failure analysis was performed with light and scanning electron microscopies. Data were statistically analyzed using ANOVA, Tukey-Test, and t-test (p < 0.05).

RESULTS

Eight crown samples (C-0.5) and one PCR specimen (PCR-0.5) revealed cracks after fatigue, resulting in an overall success rate of 87.5% (crowns: 75%, PCRs: 96.88%). Direct comparisons of PCRs versus crowns for thicknesses of 0.5 mm (p < 0.001) and 1.0 mm (p = 0.004) were significant and in favor of PCRs. Minimally invasive PCRs (0.5 and 1.0 mm) outperformed crowns with the identical ceramic thickness. No difference was detected (p = 0.276) between thickness 1.5 mm PCRs and crowns.

CONCLUSIONS

Minimally invasive monolithic CAD/CAM-fabricated posterior LDS PCRs (0.5 and 1.0 mm) resulted in superior failure load values compared to minimally invasive crowns. Minimally invasive crowns (0.5 mm) are prone to cracks after fatigue.

CLINICAL SIGNIFICANCE

Minimally invasive CAD/CAM-fabricated LDS PCR restorations with a non-retentive preparation design should be considered over single crowns for molar rehabilitation.

The effect of varying monocalcium phosphate and polylysine levels on dental composite properties

OBJECTIVES

The aim was to quantify effects of polylysine (PLS, 2 or 5 wt%) and monocalcium phosphate (MCP, 4 or 8 wt%) on properties of dental composites.

METHODS

Light-activated, lower surface polymerisation kinetics versus sample depth (1-4 mm) of 4 formulations were quantified using ATR-FTIR. Water sorption and solubility (at 1 week) were assessed following ISO/4049. PLS release (over 1 month) and biaxial flexural strength (over 6 months) of fully-cured, water-immersed, 1 mm thick discs were determined. Surface mineral precipitation, following immersion in simulated body fluid (SBF), was assessed by SEM. Z250 was used as a conventional composite comparator.

RESULTS

With 40s light exposure, increasing depth (from 1 to 4 mm) led to enhanced delay before polymerisation (from 3 to 17s) and decreased final conversion (72-66%) irrespective of PLS and MCP level. Increasing PLS and MCP raised solubility (4-13 μg/mm3). Water sorption (between 32 and 55 μg/mm3) and final PLS release (8-13% of disc content) were raised primarily by increasing PLS. Higher PLS also reduced strength. Strength reached minimum values (69-94 MPa) at 3 months. Surface mineral deposition was enhanced by increased MCP. For Z250, polymerisation delays (3-6s) and final conversions (55-54%) at 1-4 mm depth, solubility (0 μg/mm3), water sorption (16 μg/mm3) and strength (180 MPa) were all significantly different.

CONCLUSION

Delay time increased whilst final conversion decreased with thicker samples. Higher PLS enhances its percentage release, but lower level is required to keep water sorption, solubility and mechanical properties within ISO 4049 recommendations. Doubling MCP raises solubility and enhances minerals reprecipitation with minimal mechanical property compromise.

Longevity of composite restorations is definitely not only about materials

OBJECTIVES

This review study provides an overview of factors that influence the longevity of all types of direct resin composite restorations.

METHODS

A systematic search was performed in PubMed, Scopus, and Web of Science databases for articles reporting data from primary longitudinal clinical studies on composite longevity published 2011-2021. Prospective or retrospective studies with restorations in permanent dentition, with follow-up periods of at least 5 years were included.

RESULTS

In total, 33 articles were included with different study designs, practice settings, datasets, countries of origin, and sample sizes. Annual failure rates of restorations ranged from 0.08% to 6.3%. Survival rates varied between 23% and 97.7%, success rates varied between 43.4% and 98.7%. Secondary caries, fractures, and esthetic compromise were main reasons for failures. Risk factors for reduced restoration durability included patient-level factors (e.g., caries risk, parafunctional habits, number of check-ups per year, socioeconomic status), dentist factors (different operators, operator's experience), and tooth/restoration factors (endodontic treatment, type of tooth, number of restored surfaces). Patient gender and the composite used generally did not influence durability.

SIGNIFICANCE

A number of risk factors are involved in the longevity of composite restorations. Differences between composites play a minor role in durability, assuming that materials and techniques are properly applied by dentists. Patient factors play a major role in longevity. The decision-making process implemented by dentists relative to the diagnosis of aging or failed restorations may also affect the longevity of restorations. Clinicians should treat patients comprehensively and promote a healthy lifestyle to ensure longevity.

Effect of partial restorative treatment on stress distributions in non-carious cervical lesions: a three-dimensional finite element analysis

BACKGROUND

Partial restoration combined with periodontal root coverage surgery can be applied to the treatment of non-carious cervical lesions (NCCLs) accompanied with gingival recessions in clinical practice. However, the feasibility of NCCL partial restorative treatment from a biomechanical perspective remains unclear. This study aimed to investigate the effect of partial restorations on stress distributions in the NCCLs of mandibular first premolars via three-dimensional finite element analysis.

METHODS

Three-dimensional finite element models of buccal wedge-shaped NCCLs in various locations of a defected zenith (0 mm, 1 mm, and 2 mm) were constructed and divided into three groups (A, B, and C). Three partially restored NCCL models with different locations of the lower restoration border (1 mm, 1.5 mm, and 2 mm), and one completely restored NCCL model were further constructed for each group. The following restorative materials were used in all restoration models: composite resin (CR), glass-ionomer cement (GIC), and mineral trioxide aggregate (MTA). The first principal stress distributions under buccal oblique loads of 100 N were analyzed. Restoration bond failures were also evaluated based on stress distributions at dentin-restoration interfaces.

RESULTS

When the partial restoration fully covered the defected zenith, the first principal stress around the zenith decreased and the maximum tensile stress was concentrated at the lower restoration border. When the partial restoration did not cover the defected zenith, the first principal stress distribution patterns were similar to those in unrestored models, with the maximum tensile stress remaining concentrated at the zenith. As the elastic modulus of the restorative material was altered, the stress distributions at the interface were not obviously changed. Restoration bond failures were not observed in CR, but occurred in GIC and MTA in most models.

CONCLUSIONS

Partial restorations that fully covered defected zeniths improved the stress distributions in NCCLs, while the stress distributions were unchanged or worsened under other circumstances. CR was the optimal material for partial restorations compared to GIC and MTA.

Renewal MI Dental Composite Etch and Seal Properties

This study's aim was to assess whether the Renewal MI composite can self-etch enamel, seal sound cavities, and stabilize demineralized dentine. Etching was assessed using scanning electron microscopy (SEM). Cavity sealing was quantified using the ISO-11405 dye microleakage test. Demineralized dentine stabilization was evaluated by visualizing resin tag formation, enzyme activity and mineral precipitation at the adhesion interface. Renewal MI provided a mild etching of sound enamel in comparison with 37% phosphoric acid. It provided a comparable seal of sound cavities to Z250/Scotchbond Universal adhesive and a superior seal to Activa, Fuji IX and Fuji II LC. With demineralized dentine, Renewal MI formed 300-400 µm resin tags covering 63% of the adhesion interface compared with 55 and 39% for Z250/Scotchbond and Activa. Fuji IX and Fuji II LC formed no resin tags. A higher tag percentage correlated with lower surface enzyme activity. Unlike Activa and Fuji II LC, Renewal MI promoted mineral precipitation from simulated body fluid, occluding adjacent dentinal tubules within 6 months. These novel etching and sealing properties may facilitate Renewal MI's application in minimally invasive dentistry.

A Retrospective Clinical Study on Factors Influencing the Failure of NCCL Restorations

Objectives

This retrospective study evaluated the factors influencing the clinical failure of noncarious cervical lesion (NCCL) restorations.

Methods

Patients were routinely treated by undergraduate or postgraduate students and randomly received a clinical recall evaluation. A retrospective study was performed with two experienced calibrated examiners to evaluate NCCL restorations, including the critical parameters of retention, caries, marginal discoloration, and marginal integrity. The factors related to the restoration included gender, age, arch site, tooth position, the presence of occlusal wear facets, caries risk, operator, adhesive strategy, and composite. The clinical failure comparison between the parameters and factors was performed using the binary logistic regression analysis.

Results

A total of 460 cervical restorations from 96 patients were evaluated. The adhesive strategy and the presence of occlusal wear facets were the most important factors influencing the parameter failure. Therefore, the highest failure was marginal integrity, in which the gingival marginal integrity failure was 50.7%, and the occlusal marginal integrity failure was 42.4%.

Conclusions

The main factors influencing clinical failure for partial loss, marginal discoloration, and marginal integrity were the adhesive strategy and the presence of occlusal wear facets. Therefore, marginal integrity was the most frequent failure parameter.

Posterior minimally invasive full-veneers: Effect of ceramic thicknesses, bonding substrate, and preparation designs on failure-load and -mode after fatigue

OBJECTIVE

To evaluate the effect of ceramic thicknesses, bonding surface (enamel vs. dentin), and preparation design (box vs. no box) on the fatigue survival and failure load of minimally invasive full-veneer restorations.

MATERIALS AND METHODS

Human-premolars (n = 60) were divided into five test groups (n = 12). All teeth received full-veneer preparation with the following occlusal/labial thicknesses: standard: 1.5/0.8 mm; thin: 1.0/0.6 mm; ultrathin 0.5/0.4 mm. Preparations for each ceramic thickness were refined in enamel (E-1.0 and E-0.5) or dentin (D-1.5, D-1.0, and D-0.5). Control groups DB-1.5, EB-1.0, and EB-0.5 received box preparations. Monolithic lithium disilicate restorations (IPS-e.max-Press, Ivoclar Vivadent) were adhesively cemented (Syntac-Classic/Variolink-II, Ivoclar Vivadent) and subjected to cyclic mechanical loading (F = 49 N, 1.2 million cycles) with simultaneous thermocycling (5-55°C). All specimens were exposed to single load-to-failure. Pair-wise differences were calculated by using a linear regression model and Student-Newman-Keuls method (p < 0.05).

RESULTS

All full-veneers of group D-1.5, E-1.0, E-0.5, DB-1.5, EB-1.0, and EB-0.5 survived fatigue. Two full-veneers (D-1.0 and D-0.5) revealed cracks during fatigue, resulting in an overall fatigue survival rate of 98.1%. Mean load-to-failure values (N) were as followed: 1005 (D-1.5); 866 (D-1.0); 816 (D-0.5); 1495 (E-1.0); 1279 (E-0.5); 1129 (DB-1.5); 1087 (EB-1.0); and 833 (EB-0.5). Irrespective of ceramic thicknesses, enamel-based full-veneers resulted in higher failure loads than dentin-based restorations. Box preparation reduced the failure loads of thin and ultrathin enamel-based restorations.

CONCLUSION

All tested monolithic lithium disilicate full-veneer restorations exceeded physiological masticatory forces. Minimally invasive full-veneer restorations with enamel as a bonding surface and a non-retentive preparation design showed superior performance.

CLINICAL SIGNIFICANCE

Enamel-based non-retentive full-veneers made of monolithic lithium disilicate may serve as a reliable and esthetical minimally invasive treatment option for premolars.

Composite restorations placed in non-carious cervical lesions-Which cavity preparation is clinically reliable?

The purpose of this in-vivo study was to evaluate the clinical performance of restorations placed in non-carious cervical lesions (NCCLs), using different cavity preparation designs, after 7.7 years. A total of 85 NCCLs with coronal margins in enamel and cervical margins in dentin were randomly assigned to the following treatment protocols: dentin surface cleaning, dentin surface roughening with round bur plus flowable composite, dentin surface roughening/cervical groove preparation with round bur, dentin surface roughening/cervical groove preparation with round bur plus flowable composite. After enamel beveling and selective enamel etching, the defects were restored with composite. The restorations were assessed by two independent, calibrated and blinded investigators, using modified USPHS criteria. At 7 years (7.7 (± 0.35)), a total of 64 restorations (75.3%) were available for follow-up examination. The total retention rate, irrespective of the test groups, was 82.8%. Restorations placed without any preparation showed the highest loss rate (27.8%). Esthetic appearance, marginal adaptation, anatomic form and marginal discoloration did not differ significantly between the groups. Composites are long-term stable materials for restoring NCCLs. Restorations placed without any dentin preparation (cavity cleaning only) showed the highest loss rate.

Catechin-based Dentin Pretreatment and the Clinical Performance of a Universal Adhesive: A Two-year Randomized Clinical Trial

CLINICAL RELEVANCE

At 24 months, the dentin pretreatment with epigallocatechin-3-gallate did not impair the clinical performance of the adhesive Single Bond Universal regardless of the bonding strategy used.

SUMMARY

Purpose: To evaluate the two-year effect of dentin pretreatment with epigallocatechin-3-gallate (EGCG) on the clinical performance of restorations of noncarious cervical lesions (NCCLs) with Single Bond Universal, applied in two different modes (self-etch and etch-and-rinse).Methods and Materials: In this randomized clinical trial, 33 volunteers were selected, and 156 NCCLs were assigned to four groups: ER, etch-and-rinse; ER-EGCG, 0.1% EGCG dentin pretreatment + etch-and-rinse; SE, self-etch; and SE-EGCG, 0.1% EGCG dentin pretreatment + self-etch. The NCCLs were restored with a nanofilled resin composite and evaluated at baseline and at six, 12, 18, and 24 months using FDI criteria for retention, marginal staining, marginal adaptation, caries, and postoperative sensitivity. Two evaluators were blinded to the treatments performed, and impressions were taken for resin replicas to allow indirect observations. Statistical analyses were performed with Kruskal-Wallis and McNemar tests with a significance level of 5%.Results: Six restorations (one from ER, two from SE, one from ER-EGCG, and two from SEEGCG) were lost at 24 months with no significant differences (p>0.05). The retention rates were 97.0% (ER and ER-EGCG), 94.1% (SE), and 94.2% (SE-EGCG). For marginal adaptation, a significant difference was detected between the baseline and 24 months for the SE group (p=0.0313). There were no statistical differences among all other evaluated criteria at 24 months, neither for each group at baseline nor for 24-month comparisons (p>0.05).Conclusions: The pretreatment with EGCG provided no benefit in the clinical performance of the adhesive regardless of the bonding strategy used. In addition, it adds an additional required step to the restorative procedure.