Bond strength and surface roughness assessment of novel antimicrobial polymeric coated dental cement

Resin cement integrated with zein-incorporated magnesium oxide nanoparticles has previously been found to inhibit oral microbes and decrease bacterial biofilm. However, the bond strength and surface features of this biomaterial have yet to be investigated. The objective of this study was to evaluate the shear bond strength, mode of fracture, and surface roughness of resin cement modified with zein-incorporated magnesium oxide nanoparticles. Characterization of the cement was performed by X-ray diffraction, field emission scanning electron microscopy, and Fourier transform infrared spectroscopy. 126 human teeth were divided into 3 groups and cemented to lithium disilicate ceramic using resin cement with zein-incorporated magnesium oxide nanoparticles at concentrations of 0%, 1%, and 2% (n = 42). 21 samples of each group were subjected to the shear bond strength test, while the other 21 underwent thermocycling for 10,000 cycles before the test, after which all samples were evaluated for the mode of fracture. To assess surface roughness, resin cement disks were analyzed by a profilometer before and after undergoing thermocycling for 10,000 cycles. The shear bond strength of the cement with 1% and 2% nanoparticles was significantly higher than the control before thermocycling. The mode of fracture was found to be mainly adhesive with all groups, with the unmodified cement presenting the highest cohesive failure. There was no significant difference in surface roughness between the groups before or after thermocycling. The addition of zein-incorporated magnesium oxide nanoparticles to resin cement improved or maintained the shear bond strength and surface roughness of the resin cement.

Topography hierarchy of biocompatible polyhydroxyalkanoate film

Polyhydroxyalkanoates (PHAs) are used for various biomedical applications due to their biocompatibility. Surface properties, such as surface roughness, are crucial for PHAs performance. Traditional parameters used for the characterization of surface roughness, such as R a, are often insufficient to capture the complex and hierarchical (multiscale) topography of PHA films. We measure the topography and surface roughness of thin PHA films with atomic force microscopy and analyze the topography data using several relatively novel data processing methods, including the calculation of autocorrelation functions, topological data analysis, and the distribution of minimum and maximum values of pixels over the topography data. The results provide details of multiscale and anisotropic surface properties that are crucial to PHAs biocompatibility but often overlooked by traditional topography analysis methods.

Cellular responses to 3D printed dental resins produced using a manufacturer recommended printer versus a third party printer

PURPOSE

The aim of this study was to evaluate the influence of different 3D dental resins, using a manufacturer recommended printer and a third-party printer, on cellular responses of human gingival cells.

MATERIALS AND METHODS

Three NextDent resins (Denture 3D+, C&B MFH and Crowntec) were used to produce specimens on printers NextDent 5100 (groups ND, NC and NT, respectively) and Phrozen Sonic Mini 4K (groups PD, PC and PT, respectively). Human gingival fibroblasts were cultured and biocompatibility was evaluated on days 1, 3 and 7. IL-6 and IL-8 concentrations were evaluated at 3 days using ELISA. Surface roughness was evaluated by a contact profilometer. SEM and fluorescence micrographs were analyzed at days 1 and 7. Statistical analyses were performed using SPSS and mean differences were tested using ANOVA and post-hoc Tukey tests (P < .05).

RESULTS

There was an increase in cellular viability after 7 days in groups PC and PT, when compared to group PD. ND group resulted in higher concentration of IL-6 when compared to PT group. SEM and fluorescence micrographs showed less adhesion and thinner morphology of fibroblasts from group PD. No significant differences were found regarding surface roughness.

CONCLUSION

The use of different printers or resins did not seem to influence surface roughness. NextDent 5100 and Phrozen Sonic Mini 4K produced resins with similar cellular responses in human gingival fibroblasts. However, Denture 3D+ resin resulted in significantly lower biocompatibility, when compared to C&B MFH and Crowntec resins. Further testing is required to support its long-term use, required for complete dentures.

Clinical performance of single implant prostheses restored using titanium base abutments: A systematic review and meta-analysis

PURPOSE

The aim of this review was to evaluate the survival rates of restorations utilizing titanium base abutments (TBA) for restoring single-unit implant prostheses.

MATERIALS AND METHODS

This review was conducted following the preferred reporting items for systematic reviews and meta-analyses (PRISMA) guidelines. The focus question was: In patients who require the restoration of a single dental implant utilizing a titanium base abutment, what are the determining factors and outcomes relating to implant prosthesis prognosis and survival? A comprehensive search of databases (PubMed, EMBASE, and Cochrane Library) was conducted on 16 April 2023 and updated on 5 May 2023. Randomized clinical trials (RCT), retrospective studies and prospective studies, reporting on the use of TBA for single implant prostheses, were reviewed. A Cochrane collaboration risk of bias assessment analysis was performed for randomized clinical studies, and the Newcastle-Ottawa Scale tool was applied for non-randomized studies. A meta-analysis was performed on clinical trials reporting on survival rates of both TBA and other abutments. Other clinical studies, reporting on TBA only, were included for descriptive statistics.

RESULTS

The search provided 1159 titles after duplicates were removed. Six RCTs were included to perform a meta-analysis and compare the survival of the TBA to other abutments [OR 0.74; 95% CI: 0.21-2.63, heterogeneity; I2 0%; p = .99]. Twenty-three prospective and retrospective studies fulfilled the criteria and were included in the meta-analysis after 12 months of function. A total of 857 single implant-supported prostheses fabricated with a TBA were included. TBA abutments have an estimate 98.6% survival rate after 1 year in function (95% CI: 97.9%-99.4%). The mean follow-up period was 31.2 ± 16.9 months.

CONCLUSIONS

Single implant prosthesis restored with titanium base abutments showed favourable short-term survival rates.

Incomplete Polymerization of Dual-Cured Resin Cement Due to Attenuated Light through Zirconia Induces Inflammatory Responses

Zirconia restorations are becoming increasingly common. However, zirconia reduces the polymerization of dual-cured resin cement owing to light attenuation, resulting in residual resin monomers. This study investigated the effects of dual-cured resin cement, with incomplete polymerization owing to attenuated light through zirconia, on the inflammatory response in vitro. The dual-cured resin cement (SA Luting Multi, Kuraray) was light-irradiated through zirconia with three thickness diameters (1.0, 1.5, and 2.0 mm). The light transmittance and the degree of conversion (DC) of the resin cement significantly decreased with increasing zirconia thickness. The dual-cured resin cement in 1.5 mm and 2.0 mm zirconia and no-irradiation groups showed significantly higher amounts of hydroxyethylmethacrylate and triethyleneglycol dimethacrylate elution and upregulated gene expression of proinflammatory cytokines IL-1β and IL-6 from human gingival fibroblasts (hGFs) and TNFα from human monocytic cells, compared with that of the 0 mm group. Dual-cured resin cement with lower DC enhanced intracellular reactive oxygen species (ROS) levels and activated mitogen-activated protein (MAP) kinases in hGFs and monocytic cells. This study suggests that dual-cured resin cement with incomplete polymerization induces inflammatory responses in hGFs and monocytic cells by intracellular ROS generation and MAP kinase activation.

Toxicity of resin-matrix cements in contact with fibroblast or mesenchymal cells

The main aim of this study was to perform an integrative review on the toxic effects of resin-matrix cements and their products in contact with fibroblasts or mesenchymal cells. A bibliographic search was performed on PubMed using the following search terms: "cytotoxicity" AND "fibroblast" OR "epithelial" OR "mesenchymal" AND "polymerization" OR "degree of conversion" OR "methacrylate" OR "monomer" AND "resin cement" OR "resin-based cement". The initial search in the available database yielded a total of 277 articles of which 21 articles were included in this review. A decrease in the viability of mouse fibroblasts ranged between 13 and 15% that was recorded for different resin-matrix cements after light curing exposure for 20 s. The viability of human fibroblasts was recorded at 83.11% after light curing for 20 s that increased up to 90.9% after light curing exposure for 40 s. Most of the studies linked the highest toxicity levels when the cells were in contact with Bis-GMA followed by UDMA, TEGDMA and HEMA. Resin-matrix cements cause a cytotoxic reaction when in contact with fibroblasts or mesenchymal cells due to the release of monomers from the polymeric matrix. The amount of monomers released from the resin matrix and their cytotoxicity depends on the polymerization parameters.

Tetrapodal ZnO-Based Composite Stents for Minimally Invasive Glaucoma Surgery

The glaucoma burden increases continuously and is estimated to affect more than 100 million people by 2040. As there is currently no cure to restore the optic nerve damage caused by glaucoma, the only controllable parameter is the intraocular pressure (IOP). In recent years, minimally invasive glaucoma surgery (MIGS) has emerged as an alternative to traditional treatments. It uses micro-sized drainage stents that are inserted through a small incision, minimizing the trauma to the tissue and reducing surgical and postoperative recovery time. However, a major challenge for MIGS devices is foreign body reaction and fibrosis, which can lead to a complete failure of the device. In this work, the antifibrotic potential of tetrapodal ZnO (t-ZnO) microparticles used as an additive is elucidated by using rat embryonic fibroblasts as a model. A simple, direct solvent-free process for the fabrication of stents with an outer diameter of 200-400 μm is presented, in which a high amount of t-ZnO particles (45-75 wt %) is mixed into polydimethylsiloxane (PDMS) and a highly viscous polymer/particle mixture is extruded. The fabricated stents possess increased elastic modulus compared to pure PDMS while remaining flexible to adapt to the curvature of an eye. In vitro experiments showed that the fibroblast cell viability was inhibited to 43 ± 3% when stents with 75 wt % t-ZnO were used. The results indicate that cell inhibiting properties can be attributed to an increased amount of protruding t-ZnO particles on the stent surface, leading to an increase in local contacts with cells and a disruption of the cell membrane. As a secondary mechanism, the released Zn ions could also contribute to the cell-inhibiting properties in the close vicinity of the stent surface. Overall, the fabrication method and the antifibrotic and mechanical properties of developed stents make them promising for application in MIGS.

Influence of surface treatment and curing mode of resin composite cements on fibroblast behavior

BACKGROUND

Human gingival fibroblast (HGF-1) cells in the connective tissue provide an effective barrier between the alveolar bone and the oral environment. Cement margins of restorations with intrasulcular preparation or cemented implant restorations are in contact with HGF cells. However, it is unknown to what extend the cement surface finish affects the behavior of HGF cells. The purpose of this study was to compare the behavior of HGF-1 cells in contact with two different resin composite cements with three different surface treatments after light-curing and autopolymerization, respectively.

METHODS

Disks of one adhesive (Multilink Automix, Ivoclar Vivadent [MLA]) and one self-adhesive (RelyX Unicem 2 Automix, 3 M [RUN]) resin composite cement were either light-cured or autopolymerized. Specimen surfaces were prepared with the oxygen inhibition layer intact, polished with P2500-grit silicon carbide paper or treated with a scaler. Cells were cultivated on the specimens for 24 h. Viability assay was performed, and cell morphology was examined with scanning electron microscopy. Additionally, roughness parameters of the specimen were analyzed with a 3D laser scanning microscope. Three-way ANOVA was applied to determine the effect of cement material, curing mode and surface treatment (a = 0.05).

RESULTS

Overall, cement material (p = 0.031), curing mode (p = 0.001), and surface treatment (p < 0.001) significantly affected relative cell viability of HGF. The autopolymerized specimen with the oxygen inhibition layer left intact displayed the lowest relative cell viability (MLA 25.7%, RUN 46.6%). Removal of the oxygen inhibition layer with a scaler increased cell viability but also resulted in higher surface roughness values.

CONCLUSIONS

HGF cell viability is affected by the surface treatment and the curing mode. The oxygen inhibition layer is an inhibitory factor for the viability of HGF cells. Autopolymerization enhances the cytotoxic potential of the oxygen inhibition layer.

A comprehensive in vitro study on the performance of two different strategies to simplify adhesive bonding

Objective

The purpose of this study is to compare the bonding performance and mechanical properties of two different resin composite cements using simplified adhesive bonding strategies.

Materials and methods

Shear bond strength of two resin composite cements (an adhesive cement: Panavia V5 [PV5] and a self‐adhesive cement: RelyX Universal [RUV]) to human enamel, dentin, and a variety of restorative materials (microfilled composite, composite, polymer‐infiltrated ceramic, feldspar ceramic, lithium disilicate and zirconia) was measured. Thermocycle aging was performed with selected material combinations.

Results

For both cements, the highest shear bond strength to dentin was achieved when using a primer (PV5: 18.0 ± 4.2 MPa, RUV: 18.2 ± 3.3 MPa). Additional etching of dentin reduced bond strength for RUV (12.5 ± 4.9 MPa). On enamel, PV5 achieved the highest bond strength when the primer was used (18.0 ± 3.1 MPa), while for RUV etching of enamel and priming provided best results (21.2 ± 6.6 MPa). Shear bond strength of RUV to restorative materials was superior to PV5. Bonding to resin‐based materials was predominantly observed for RUV.

Conclusions

While use of RUV with the selective‐etch technique is slightly more labor intensive than PV5, RUV (with its universal primer) displayed a high‐bonding potential to all tested restorative materials, especially to resin.

Clinical significance

For a strong adhesion to the tooth substrate, PV5 (with its tooth primer) is to be preferred because etching with phosphoric acid is not required. However, when using a wide range of varying restorative materials, RUV with its universal primer seems to be an adequate option.

Fibroblast behavior on conventionally processed, milled, and printed occlusal device materials with different surface treatments

STATEMENT OF PROBLEM

Occlusal devices can be either conventionally processed, milled, or printed. However, little is known about the biocompatibility of 3D printing resin materials.

PURPOSE

The purpose of this in vitro study was to compare the viability and morphology of human gingival fibroblast cells (HFG-1) after cultivation on conventionally processed, milled, and printed occlusal device materials with different surface treatments.

MATERIAL AND METHODS

Disks of a conventionally processed (PalaXpress Clear [pP]), milled (Yamahachi PMMA Clear [sY]), and 2 different printed materials (Dental LT Clear Resin [aD]; Freeprint splint [aF]) were prepared. The surfaces of the specimens were finished by using 2 different treatments (unpolished and polished with P1200-grit silicon carbide paper). HGF-1 cells were cultivated on the specimens for 24 hours, and a viability assay was performed by using polystyrene disks as a control (n=9 disks per group). Cell morphology and the topography of the specimens were examined with scanning electron microscopy (n=3 disks per group). Two-way analysis of variance was applied to determine the effect of material and surface treatment followed by the post hoc Fisher least significant difference test (α=.05).

RESULTS

Overall, material (P<.001) and surface treatment (P<.001) significantly influenced the viability of HGF-1 cells. The viability of cells on all specimens displayed mean values between 0.85 and 1.01 compared with the control except for unpolished aD (0.00 ±0.07) and aF (0.02 ±0.05) that had only a few cells with a round shape.

CONCLUSIONS

The behavior of HGF-1 cells on conventionally processed and milled specimens was similar and not dependent on the surface treatment. Unpolished printed specimens had a cytotoxic effect. However, after polishing, cell behavior was similar to that of the conventionally processed and milled specimens.

Influence of dual-cure and self-cure abutment cements for crown implants on human gingival fibroblasts biological properties

AIMS

To analyze the biological effects of the cements Relyx Unicem 2, Panavia V5, Multilink Hybrid Abutment and SoloCem on human gingival fibroblast cells (HGFs).

MATERIALS AND METHODS

HGFs were exposed to different eluates (n = 40) of the studied resin-based cements. Their cytotoxic effects and influence on cell migration were assessed using MTT and wound-healing assays, respectively. Level of HGF attachment, cell morphology and F-actin cytoskeleton content after exposition to the different eluates were analyzed by scanning electron microscopy (SEM) and confocal microscopy analysis, respectively. The levels of intracellular reactive oxygen species (ROS) produced by the eluates of the different cements were also determined by flow cytometry. Data were analyzed by one-way analysis of variance (ANOVA) followed by Tukey´s test.

RESULTS

Eluates of SoloCem significantly reduces the viability of HGFs (69% reduction compared to control at 48 h). Cell migration of HGFs in presence of undiluted SoloCem eluates was significantly lower than in the control (88% open wound area at 24 h). Contrarily, migration speed with Multilynk eluates was similar to that of the control group at all periods of time and all dilutions studied. SEM analysis showed very few cells in SoloCem group, and a moderate cell growth in Multilink, Panavia and Relyx groups were detected. Finally, ROS levels detected in HGFs treated with the more concentrated SoloCem and Relyx dilutions were significantly enhanced compared with that in the control cells or the other groups (44% and 11% ROS positive cells, respectively).

CONCLUSIONS

The results obtained in the present work suggest that Multilink hybrid abutment has better biological properties and lower cytotoxicity for cementing implant crowns on abutments.

Influence of zirconia implant surface topography on first bone implant contact within a prospective cohort study

BACKGROUND

Although 5-year clinical data exist for different zirconia implants, no analysis has yet been performed focusing on how the surface topography of the implant affects clinical parameters.

PURPOSE

To analyze the influence of zirconia implant topography on first bone implant contact (fBIC).

MATERIALS AND METHODS

In a prospective two-center cohort investigation 63 zirconia implants were evaluated at implant placement, prosthetic delivery, 1, 3, and 5 years. The distance (DIB) between implant shoulder and fBIC was measured at each time point in periapical radiographs at mesial and distal sites. Two-way ANOVA/Bonferroni was used to analyze the effects of time and center (α < 0.05).

RESULTS

Between the centers, the mean DIB varied significantly at implant placement (Freiburg [FR]: 1.4 ± 0.6 mm; Zurich [ZH]: 0.8 ± 0.5 mm). Thereafter, no statistically significant difference in DIB was observed, neither between centers nor between time points (prosthetic delivery: FR: 1.9 ± 0.6 mm, ZH: 1.7 ± 0.8 mm; 1 year: FR: 1.8 ± 0.6 mm, ZH: 1.6 ± 0.8 mm; 3 years: FR: 1.9 ± 0.8 mm, ZH: 1.7 ± 0.8 mm; 5 years: FR: 1.9 ± 0.8 mm, ZH 1.8 ± 0.6 mm). The overall mean DIB at prosthetic delivery to 5 years of both centers (1.8 ± 0.7 mm) is located within the transition zone between the smooth neck and the moderately rough intraosseous part (1.6-2.0 mm from the implant shoulder). However, individual DIB values are ranging from 0.1 to 4.2 mm overlapping the transition zone.

CONCLUSIONS

The standard deviation of the DIB indicates that the fBIC establishes on moderately rough and smooth surfaces. Consequently, soft tissue adapts to both topographies as well.

Topical fluoride varnishes promote several biological responses on human gingival cells

OBJECTIVE

To compare the in vitro cytotoxicity of four commercial topical fluoride varnishes widely used in daily dental practice for the prevention of caries on human fibroblasts: Cervitec F, Fixofluor, Fluor Protector S and Duraphat.

MATERIAL AND METHODS

Human gingival fibroblasts (hGF) were exposed to different concentrations of fluoride varnishes extracts. Biological assays, including MTT and IC50 value determination, annexin-V/7-AAD staining, cell migration and F-actin staining with phalloidin were carried out. Statistical analyses were performed using one-way ANOVA and Tukey's post hoc test.

RESULTS

At 4% concentration, all of the fluoride varnishes extracts affected fibroblasts metabolic activity, exhibiting a high degree of cytotoxicity at all measured time points. At 0.1% and 1%, Duraphat and Fixofluor or Fluor Protector S and Cervitec F exerted the lowest or highest cytotoxic effects, respectively. Similar effects were evidenced when induction of apoptosis/necrosis and cell migration assays were analyzed. Immunocytochemical assays revealed a similar number of fibroblasts, without changes in the morphology and F-actin content at 0.1% concentration of all tested materials, while at 1% concentration, Fluor Protector S and Cervitec F showed few cells with aberrant morphology or non-adhered cells, respectively.

CONCLUSIONS

Different commercial topical fluoride varnishes with the same therapeutic indication may exhibit different biological effects and cytotoxicity on fibroblasts.