Influence of restoration thickness on the stress distribution of ultrathin ceramic onlay rehabilitating canine guidance: a 3D-finite element analysis

Fatigue behavior of endodontically treated maxillary premolars with MOD defects under different minimally invasive restorations

OBJECTIVES

To analyze the stress distribution and subsequent fracture resistance of human maxillary premolars with mesial-occlusal-distal (MOD) defects restored with different minimally invasive restorations.

MATERIALS AND METHODS

Seventy non-carious human maxillary premolars were selected and divided into seven groups (n = 10). Ten teeth without further preparation served as control. The remaining teeth were endodontically treated and received three restorative patterns: inlays without cusp coverage (I), onlays with palatal coverage (O), overlays with both buccal and palatal coverage (Ov). Lithium disilicate glass ceramics (EM) and machinable composite resin (LU) were used for restoration. Specimens were tested under cycling loading with tongue direction of 45° for 1.2 × 10⁶ cycles at a 50-N load and 2.0-Hz frequency. The survival time and two fracture mode classifications were assessed. Three-dimensional models of each group were designed. The magnitude and pattern of stresses were analyzed under the same condition of the in vitro test using finite element stress analysis.

RESULTS

Although the overlay model pattern produced more favorable stress distribution, three restorative patterns restored with the same material had no difference in survival curves (P > 0.05). Only the survival curve of the EM-Ov group had no statistical difference with that of the control group (P > 0.05). EM groups presented mainly interface adhesive failure, while LU groups were mainly material cohesive failure.

CONCLUSION

For the endodontically treated maxillary premolars with MOD defect, the lithium disilicate glass ceramic overlay pattern can reach the best restorative effect.

CLINICAL RELEVANCE

Comparing with restorative pattern, restorative material had a greater influence on the minimally invasive restoration of posterior teeth.

The Influence of Custom-Milled Framework Design for an Implant-Supported Full-Arch Fixed Dental Prosthesis: 3D-FEA Sudy

The current study aimed to evaluate the mechanical behavior of two different maxillary prosthetic rehabilitations according to the framework design using the Finite Element Analysis. An implant-supported full-arch fixed dental prosthesis was developed using a modeling software. Two conditions were modeled: a conventional casted framework and an experimental prosthesis with customized milled framework. The geometries of bone, prostheses, implants and abutments were modeled. The mechanical properties and friction coefficient for each isotropic and homogeneous material were simulated. A load of 100 N load was applied on the external surface of the prosthesis at 30° and the results were analyzed in terms of von Mises stress, microstrains and displacements. In the experimental design, a decrease of prosthesis displacement, bone strain and stresses in the metallic structures was observed, except for the abutment screw that showed a stress increase of 19.01%. The conventional design exhibited the highest stress values located on the prosthesis framework (29.65 MPa) between the anterior implants, in comparison with the experimental design (13.27 MPa in the same region). An alternative design of a stronger framework with lower stress concentration was reported. The current study represents an important step in the design and analysis of implant-supported full-arch fixed dental prosthesis with limited occlusal vertical dimension.

Effect of the restorative technique on load-bearing capacity, cusp deflection, and stress distribution of endodontically-treated premolars with MOD restoration

Objectives

To evaluate the influence of the restorative technique on the mechanical response of endodontically-treated upper premolars with mesio-occluso-distal (MOD) cavity.

Materials and Methods

Forty-eight premolars received MOD preparation (4 groups, n = 12) with different restorative techniques: glass ionomer cement + composite resin (the GIC group), a metallic post + composite resin (the MP group), a fiberglass post + composite resin (the FGP group), or no endodontic treatment + restoration with composite resin (the CR group). Cusp strain and load-bearing capacity were evaluated. One-way analysis of variance and the Tukey test were used with α = 5%. Finite element analysis (FEA) was used to calculate displacement and tensile stress for the teeth and restorations.

Results

MP showed the highest cusp (p = 0.027) deflection (24.28 ± 5.09 µm/µm), followed by FGP (20.61 ± 5.05 µm/µm), CR (17.72 ± 6.32 µm/µm), and GIC (17.62 ± 7.00 µm/µm). For load-bearing, CR (38.89 ± 3.24 N) showed the highest, followed by GIC (37.51 ± 6.69 N), FGP (29.80 ± 10.03 N), and MP (18.41 ± 4.15 N) (p = 0.001) value. FEA showed similar behavior in the restorations in all groups, while MP showed the highest stress concentration in the tooth and post.

Conclusions

There is no mechanical advantage in using intraradicular posts for endodontically-treated premolars requiring MOD restoration. Filling the pulp chamber with GIC and restoring the tooth with only CR showed the most promising results for cusp deflection, failure load, and stress distribution.