Controlled release multiple layer coatings

Controlled release of ropinirole hydrochloride from a multiple barrier layer tablet dosage form: effect of polymer type on pharmacokinetics and IVIVC

The purpose of the present study was to control in vitro burst effect of the highly water-soluble drug, ropinirole hydrochloride to reduce in vivo dose dumping and to establish in vitro-in vivo correlation. The pharmacokinetics of two entirely different tablet formulation technologies is also explored in this study. For pharmacokinetics study, FDA recommends at least 10% difference in drug release for formulations to be studied but here a different approach was adopted. The formulations F8A and F9A having similar dissolution profiles among themselves and with Requip® XL™ (f 2 value 72, 77, 71 respectively) were evaluated. The C max of formulation F8A comprising hypromellose 100,000 cP was 1005.16 pg/ml as compared to 973.70 pg/ml of formulation F9A comprising hypromellose 4000 cP irrespective of T max of 5 and 5.75 h, respectively. The difference in release and extent of absorption in vivo was due to synergistic effect of complex RH release mechanism; however, AUC0-t and AUC0-∞ values were comparable. The level A correlation using the Wagner-Nelson method supported the findings where R (2) was 0.7597 and 0.9675 respectively for formulation F8A and F9A. Thus, in vivo studies are required for proving the therapeutic equivalency of different formulation technologies even though f 2 ≥ 50. The technology was demonstrated effectively at industrial manufacturing scale of 200,000 tablets.

A novel approach to a fine particle coating using porous spherical silica as core particles

Abstract The applicability of porous spherical silica (PSS) was evaluated as core particles for pharmaceutical products by comparing it with commercial core particles such as mannitol (NP-108), sucrose and microcrystalline cellulose spheres. We investigated the physical properties of core particles, such as particle size distribution, flow properties, crushing strength, plastic limit, drying rate, hygroscopic property and aggregation degree. It was found that PSS was a core particle of small particle size, low friability, high water adsorption capacity, rapid drying rate and lower occurrence of particle aggregation, although wettability is a factor to be carefully considered. The aggregation and taste-masking ability using PSS and NP-108 as core particles were evaluated at a fluidized-bed coating process. The functional coating under the excess spray rate shows different aggregation trends and dissolution profiles between PSS and NP-108; thereby, exhibiting the formation of uniform coating under the excess spray rate in the case of PSS. This expands the range of the acceptable spray feed rates to coat fine particles, and indicates the possibility of decreasing the coating time. The results obtained in this study suggested that the core particle, which has a property like that of PSS, was useful in overcoming such disadvantages as large particle size, which feels gritty in oral cavity; particle aggregation; and the long coating time of the particle coating process. These results will enable the practical fine particle coating method by increasing the range of optimum coating conditions and decreasing the coating time in fluidized bed technology.

Influence of the percentage of acetylation on the assembly of LbL multilayers of poly(acrylic acid) and chitosan

The Layer-by-Layer (LbL) self-assembly of polyelectrolyte multilayers (PEMs) formed by poly(acrylic acid) (PAA) and chitosan (CHI) of two different percentages of acetylation (AC) has been studied by dissipative quartz crystal microbalance (D-QCM) and ellipsometry. The results point out that the non-linear growth (exponential growth) of the films is not modified by the percentage of acetylation of the CHI (AC). The comparison of the thickness obtained by D-QCM and by ellipsometry has allowed us to calculate the water content of the films showing that the multilayers are highly hydrated. This agrees with the values of the complex shear modulus obtained from the analysis of D-QCM data that are in the MPa range, and show a transition from a viscous to mainly elastic behavior depending on the charge density of the CHI chains. The monomer surface density in each layer (obtained from the combination of ellipsometry and differential refractive index measurements) indicated that the mechanism of charge compensation depends on the percentage of acetylation of the CHI. It was found that the adsorption kinetics is a bimodal process with characteristic times that depend on the number and nature of each layer. The load capacity of the multilayers for a β-blocker, propranolol, was found to be higher for the lowest acetylation degree.

pH-induced changes in the fabrication of multilayers of poly(acrylic acid) and chitosan: fabrication, properties, and tests as a drug storage and delivery system

Multilayers of poly(acrylic acid), PAA, and chitosan, CHI, have been built by the layer-by-layer (LbL) method from aqueous solutions at different pH values and analyzed by the dissipative quartz crystal microbalance (D-QCM) and ellipsometry. The results showed that under all of the assembly conditions considered the growth of the films is nonlinear. The thickness of the PAA layers increases as the pH of the assembling solutions decreases, whereas the adsorption of CHI is almost unaffected by the pH conditions. The comparison of the thickness obtained by D-QCM and by ellipsometry has allowed us to calculate the water content of the films, showing that the multilayers are highly hydrated, with an average water content higher than 20%. The analysis of D-QCM data has provided high-frequency values of the complex shear modulus that are in the megapascal range and shows a transition from mainly viscous to mainly elastic behavior for the added PAA layers, depending on the pH. The monomer surface density in each layer (obtained from the combination of ellipsometry and differential refractive index measurements) indicated that the monomer density depends on the assembly conditions. It was found that the adsorption kinetics is a bimodal process, with characteristic times that depend on the number and nature of the layers. Finally, the possibility of using of these multilayers as a drug storage and delivery system has been evaluated.