Plasticizing effect of ibuprofen induced an alteration of drug released from Kollidon SR matrices produced by direct compression

Investigations on the Impacts of Drugs or Excipients with Different Physicochemical and Compaction Properties on the Disintegration Behavior of Kollidon®SR-Based Binary Controlled Release Matrix Tablets

The objective of this study was to examine the impact of the physicochemical properties of the loaded drug or excipient, the concentration of Kollidon®SR (KSR), and the mechanical characteristics of KSR compacts on their disintegration times. Using disintegration apparatus, a two-hour constraint was chosen as the process's end point. Lactose-KSR compacts subjected to the highest compression pressure and Microcrystalline cellulose-KSR compacts with KSR concentrations exceeding 30% exhibited disintegration times of less than ten minutes. Likewise, compacts containing Diltiazem HCl-KSR demonstrated brief disintegration times across all tested KSR concentrations and compression pressures. Compacts of Modafinil, Metformin HCl, and Ascorbic acid-KSR displayed disintegration times ranging from fast to moderate, contingent upon the levels of KSR and compression pressure applied. Compacts containing KSR with Aspirin, Salicylic acid, or Ibuprofen did not exhibit significant disintegration even at minimal amounts of KSR (0.5%). Theophylline-KSR tablets also showed prolonged dissolution times, even at very low concentrations of KSR. The disintegration times of Dic-KSR tablets were roughly close to an hour and were predominantly unaffected by varying KSR levels and only marginally influenced by compression pressures. It is possible to draw the conclusion that different drugs or excipients have different minimum KSR requirements to resist compacts' disintegration process. Compounds that demonstrate low solubility in water can result in extended disintegration times for KSR compacts. The melting points of these compounds, in conjunction with the Py values of the compacts and their compaction properties, could affect the disintegration process, although a precise evaluation is necessary.

Novel Glyceryl Monostearate- and Polyethylene Glycol 6000-Based Ibuprofen Pellets Prepared by Hot-Melt Extrusion: Evaluation and Stability Assessment

Purpose

To prepare stable sustained-release (SR) pellets, containing high ibuprofen (IBU) loading, by hot-melt extrusion (HME) technique using polyethylene glycol 6000 (PEG 6000) and glyceryl monostearate (GMS).

Methods

HME pellets (60% w/w IBU) were prepared using PEG 6000, GMS, and mixture of both polymers (1:1). Stability studies were performed under stress conditions (40 °C and relative humidity “RH” of 75%) for 6 months and at room temperature for 12 months. Fresh and stored IBU pellets were evaluated by drug content (HPLC), release rate study (USP apparatus IV), DSC, and XRD.

Results

HME succeeded to produce SR-IBU pellets with high drug loading. PEG 6000 gave higher IBU release rate and relatively unstable formula after storage. PEG 6000/GMS mixture gave prolonged IBU release up to 4 h with stable formula for 12 months at room temperature. While, IBU/GMS pellets gave SR profile up to 6 h and a stable formula under both testing conditions. These advantages of IBU/GMS pellets could be an excellent candidate for SR-IBU product. DSC and XRD analysis data (enthalpy and counts) for IBU and polymers gave a mirror image for IBU release profiles of the studied HME pellets, for both fresh and stored samples.

Conclusion

Stable SR-IBU/GMS HME pellets with high IBU loading (60% w/w) were successfully produced, for the first time, without any other excipients.

Potential Use of Polyvinyl Acetate-Polyvinylpyrrolidone Mixture for the Development of Atenolol Sustained Release Matrix Tablets: Optimization of Formulation through in Vitro-in Vivo Assessment Study

The objective of this study was to develop sustained release matrix tablets of atenolol (AT) using different concentrations of polyvinyl acetate-polyvinylpyrrolidone mixture (KSR) (20, 30, or 40%) with various types of fillers such as spray dried lactose (SP.D.L), avicel pH 101 (AV), and emcompress (EMS). The physical characteristics of the prepared tablets were evaluated. Characterization of the optimized formulation was performed using Fourier transform (FT)-IR spectroscopy and differential scanning calorimetry (DSC). Moreover, the in vitro release profiles of AT formulations were investigated in different pH dissolution media. Drug release kinetics and mechanisms were also determined. The results revealed that there was no potential incompatibility of the drug with the polymer. The release profiles of AT were affected by the concentration of KSR, fillers used, and pH of the dissolution media. The drug release kinetic from most of the formulations obeyed Higuchi diffusion model. The selected formulae were investigated for their stability by storage at 30 and 40°C with atmospheric humidity and 75% relative humidity (RH), respectively. The results demonstrated that no change in the physicochemical properties of the tablets stored at 30°C/atmospheric RH in comparison with some changes at 40°C/75% RH. Finally, the in vivo study provided an evidence that the optimized AT tablet containing 40% KSR and SP.D.L exhibited prominent higher oral bioavailability and more efficient sustained-release effect than the drug alone or the commercial tablet product. It is noteworthy that KSR could be considered as a promising useful release retardant for the production of AT sustained release matrix tablets.

Thermal, mechanical and drug release characteristics of an acrylic film using active pharmaceutical ingredient as non-traditional plasticizer

The objective of this study was to investigate thermal and mechanical properties as well as in vitro drug release of Eudragit® RL (ERL) film using chlorpheniramine maleate (CPM) as either active pharmaceutical ingredient or non-traditional plasticizer. Differential scanning calorimeter was used to measure the glass transition temperature (Tg) of 0-100% w/w CPM in ERL physical mixture. Instron testing machine was used to investigate Young's modulus, tensile stress and tensile strain (%) of ERL film containing 20-60% w/w CPM. Finally, a Franz diffusion cell was used to study drug release from ERL films obtained from four formulations, i.e. CRHP0/0, CRHP0/5, CRHP2/0 and CRHP2/5. The Tg of ERL was decreased when the weight percentage of CPM increased. The reduction of the Tg could be described by Kwei equation, indicating the interaction between CPM and ERL. Modulus and tensile stress decreased whereas tensile strain (%) increased when weight percentage of CPM increased. The change of mechanical properties was associated with the reduction of the Tg when weight percentage of CPM increased. ERL films obtained from four formulations could release the drug in no less than 10 h. Cumulative amount of drug release per unit area of ERL film containing only CPM (CRHP0/0) was lower than those obtained from the formulations containing traditional plasticizer (CRHP0/5), surfactant (CRHP2/0) or both of them (CRHP2/5). The increase of drug release was a result of the increase of drug permeability through ERL film and drug solubility based on traditional plasticizer and surfactant, respectively.