Stem subsidence of polished and rough double-taper stems: in vitro mechanical effects on the cement-bone interface

Prophylactic cable prevents tapered titanium stem subsidence with 2 cm of stem-cortical engagement in a cadaveric model

Aims

When performing revision total hip arthroplasty using diaphyseal-engaging titanium tapered stems (TTS), the recommended 3 to 4 cm of stem-cortical diaphyseal contact may not be available. In challenging cases such as these with only 2 cm of contact, can sufficient axial stability be achieved and what is the benefit of a prophylactic cable? This study sought to determine, first, whether a prophylactic cable allows for sufficient axial stability when the contact length is 2 cm, and second, if differing TTS taper angles (2° vs 3.5°) impact these results.

Methods

A biomechanical matched-pair cadaveric study was designed using six matched pairs of human fresh cadaveric femora prepared so that 2 cm of diaphyseal bone engaged with 2° (right femora) or 3.5° (left femora) TTS. Before impaction, three matched pairs received a single 100 lb-tensioned prophylactic beaded cable; the remaining three matched pairs received no cable adjuncts. Specimens underwent stepwise axial loading to 2600 N or until failure, defined as stem subsidence > 5 mm.

Results

All specimens without cable adjuncts (6/6 femora) failed during axial testing, while all specimens with a prophylactic cable (6/6) successfully resisted axial load, regardless of taper angle. In total, four of the failed specimens experienced proximal longitudinal fractures, three of which occurred with the higher 3.5° TTS. One fracture occurred in a 3.5° TTS with a prophylactic cable yet passed axial testing, subsiding < 5 mm. Among specimens with a prophylactic cable, the 3.5° TTS resulted in lower mean subsidence (0.5 mm (SD 0.8)) compared with the 2° TTS (2.4 mm (SD 1.8)).

Conclusion

A single prophylactic beaded cable dramatically improved initial axial stability when stem-cortex contact length was 2 cm. All implants failed secondary to fracture or subsidence > 5 mm when a prophylactic cable was not used. A higher taper angle appears to decrease the magnitude of subsidence but increased the fracture risk. The fracture risk was mitigated by the use of a prophylactic cable.

Collarless Polished Tapered Stems of Identical Shape Provide Differing Outcomes for Stainless Steel and Cobalt Chrome: A Biomechanical Study

Cemented polished tapered femoral stems (PTS) made of cobalt-chrome alloy (CoCr) are a known risk factor for periprosthetic fracture (PPF). The mechanical differences between CoCr-PTS and stainless-steel (SUS) PTS were investigated. CoCr stems having the same shape and surface roughness as the SUS Exeter^® stem were manufactured and dynamic loading tests were performed on three each. Stem subsidence and the compressive force at the bone-cement interface were recorded. Tantalum balls were injected into the cement, and their movement was tracked to indicate cement movement. Stem motions in the cement were greater for the CoCr stems than for the SUS stems. In addition, although we found a significant positive correlation between stem subsidence and compressive force in all stems, CoCr stems generated a compressive force over three times higher than SUS stems at the bone-cement interface with the same stem subsidence (p < 0.01). The final stem subsidence amount and final force were greater in the CoCr group (p < 0.01), and the ratio of tantalum ball vertical distance to stem subsidence was significantly smaller for CoCr than for SUS (p < 0.01). CoCr stems appear to move more easily in cement than SUS stems, which might contribute to the increased occurrence of PPF with the use of CoCr-PTS.

Relationship between the Surface Roughness of Material and Bone Cement: An Increased "Polished" Stem May Result in the Excessive Taper-Slip

Although some reports suggest that taper-slip cemented stems may be associated with a higher periprosthetic femoral fractures rate than composite-beam cemented stems, few studies have focused on the biomaterial effect of the polished material on the stem–cement interface. The purpose of this study was to investigate the relationship between surface roughness of materials and bone cement. Four types of metal discs—cobalt-chromium-molybdenum alloy (CoCr), stainless steel alloy 316 (SUS), and two titanium alloys (Ti-6Al-4V and Ti-15Mo-5Zr-3Al)—were prepared. Five discs of each material were produced with varying degrees of surface roughness. In order to evaluate surface wettability, the contact angle was measured using the sessile drop method. A pin was made using two bone cements and the frictional coefficient was assessed with a pin-on-disc test. The contact angle of each metal increased with decreasing surface roughness and the surface wettability of metal decreased with higher degrees of polishing. With a surface roughness of Ra = 0.06 μm and moderate viscosity bone cement, the frictional coefficient was significantly lower in CoCr than in SUS (p = 0.0073). In CoCr, the low adhesion effect with low frictional coefficient may result in excessive taper-slip, especially with the use of moderate viscosity bone cement.

Femoral Stem Cementation in Hip Arthroplasty: The Know-How of a "Lost" Art

PURPOSE OF REVIEW

To describe the (1) indications, (2) preoperative precautions, and (3) stepwise technical details of modern femoral stem cemented fixation.

RECENT FINDINGS

Femoral stem cementation provides excellent implant longevity with a low periprosthetic fracture rate among patients with compromised bone quality or aberrant anatomy. Unfamiliarity with the details of modern cementation techniques among trainees who may lack frequent exposure to cementing femoral stems may preclude them from offering this viable option to suitable patients in later stages of their careers. As such, maximizing benefit from cemented femoral stem fixation among suitable candidates is contingent upon the meticulous use of modern cementation techniques. In addition to proper patient selection, modern cementation techniques emphasize the use of (1) pulsatile lavage of the femoral canal, (2) utilization of epinephrine-soaked swabs, (3) vacuum cement mixing, (4) retrograde cement introduction, (5) cement pressurization, and (6) the use of stem centralizers. Furthermore, identifying and optimizing the preoperative status of at-risk patients with pre-existing cardiopulmonary compromise, in addition to intraoperative vigilance, are essential for mitigating the risk of developing bone cement implantation syndrome. Further research is required to assess the utility of cemented femoral stem fixation among younger patients.

The effects of patient characteristics and stem alignment on distal femoral cortical hypertrophy after cemented polished tapered stem implantation

BACKGROUND

The objective of this study was to evaluate the results of over 10 years of total hip arthroplasty (THA) practice with Exeter^TM stems and the clinical relevance of distal femoral cortical hypertrophy (DFCH).

METHODS

We retrospectively reviewed 127 hips (120 patients) that had undergone THA with Exeter^TM stems between 2004 and 2007. Kaplan-Meier survival analyses for the stem of all 127 hips were performed using different endpoints. Of 127 hips, 100 (94 patients) had complete 10-year follow-up data, including the Japanese Orthopaedic Association Hip Disease Evaluation Questionnaire (JHEQ) as the patient-reported outcomes, and the clinical relevance of DFCH was analyzed using multivariable logistic regression analysis.

RESULTS

The survival of the stem with the endpoint of re-operation for loosening, > 5-mm subsidence, and re-operation for any reason were 100%, 99.1% (95% CI 97.5-100%), and 98.3% (95% CI 96.0-100%), respectively. Of 100 hips followed completely for 10 years, DFCH occurred in 20 hips (20%). The satisfaction and pain visual analog scale of JHEQ revealed high satisfaction and less pain in patients with DFCH. By multivariate logistic regression analysis, body weight > 55 kg (odds ratio: 2.88, p = 0.035) and varus stem alignment (odds ratio: 6.56, p = 0.003) were found to be predictors for DFCH.

CONCLUSIONS

The incidence of DFCH with the Exeter^TM stem was 20%. A body weight > 55 kg and varus stem alignment are predictors for future DFCH. DFCH with the Exeter^TM stem indicates a good outcome with less hip pain.

Biomechanical Performance of the Cemented Hip Stem with Different Surface Finish

The integrity of the cemented fixation interface is responsible for the long-term longevity of artificial hip prostheses. Metallic stems with roughened surfaces are considered to provide stronger adhesion with cement. However, clinical studies have reported that roughened stems show a lower survival rate than polished stems. These studies clearly reveal that the causes of artificial stem loosening are very complicated and multifaceted. Therefore, this study was conducted to investigate the mechanical effect of stem surface finish in cemented hip replacement. To accomplish this, a series of cement–metal specimens were tested configurations to assess the mechanical characteristics of the cement–metal interface specimens. A finite elemental model of cemented femoral prostheses was then created, in which the cement–stem interface was assumed to be in different bonding states according to the experimentally measured interface properties. The failure probabilities of the cement mantle and cemented interface under physiological loadings were evaluated. Experimental results indicate that the polished metal produced higher interfacial tensile and lower shearing strengths than the roughened metal. The polished stems were predicted to induce a lower failure probability of cement mantle and higher integrity of the cement–stem interface when compared to the roughened stem. Overall, current results provide significant evidence to support the clinical outcomes of cemented hip prostheses with different stem surface finishes.

Effects of femoral bone defect morphology on initial polished tapered stem stability in massive defect model: a biomechanical study

Background

Good outcomes have been reported in revision total hip replacement with massive segmental defects using impaction bone grafting with circumferential metal meshes. However, the morphology of defects that require a mesh is poorly defined. The purpose of this study was to evaluate the effects of a variety of segmental defects on load transmission to the proximal femur under both axial and rotational loads.

Methods

Initial stability of the Exeter stem was investigated in a composite bone model using three medial bone defect morphologies: Long (length 5 cm × width 2 cm), Short (2.5 cm × 2 cm), Square (3.2 cm × 3.2 cm), Square with mesh (3.2 cm × 3.2 cm defect covered with metal mesh), and with no defect as control. Specimens (5 per group) were axially loaded and internally rotated up to 20° or to failure. Strain distributions of the femora were measured using a strain gauge.

Results

All Square group specimens failed while rotation was increasing. In the other four groups, failure was not observed in any specimens. Mean torsional stiffness in the Long (4.4 ± 0.3 Nm/deg.) and Square groups (4.3 ± 0.3 Nm/deg.) was significantly smaller than in the Control group (4.8 ± 0.3 Nm/deg.). In the medio-cranial region, the magnitude of the maximum principal strain in the Square group (1176.4 ± 100.9) was significantly the largest (Control, 373.2 ± 129.5, p < 0.001; Long, 883.7 ± 153.3, p = 0.027; Short, 434.5 ± 196.8, p < 0.001; Square with mesh, 256.9 ± 100.8, p < 0.001). Torsional stiffness, and both maximum and minimum principal strains in the Short group showed no difference compared to the Control group in any region.

Conclusions

Bone defect morphology greatly affected initial stem stability and load transmission. If defect morphology is not wide and the distal end is above the lower end of the lesser trochanter, it may be acceptable to fill the bone defect region with bone cement. However, this procedure is not acceptable for defects extending distally below the lower end of the lesser trochanter or defects 3 cm or more in width.

Peri-prosthetic bone remodeling and change in bone mineral density in the femur after cemented polished tapered stem implantation

OBJECTIVE

We examined longitudinal changes in bone mineral density (BMD) around the femur for 5 years after total hip arthroplasty (THA) using cemented collarless polished double-tapered stem implantation and investigated the influence of BMD changes on radiological remodeling of the femur.

MATERIALS AND METHODS

Sixty hips from 56 patients who underwent cemented THA with a collarless polished double-tapered stem were included. BMD was measured 2 weeks postoperatively (baseline), 3 months, 6 months, 1 year and annually thereafter until 5 years after surgery using dual-energy X-ray absorptiometry on the lumbar spine and proximal femur of the operated side according to the Gruen's zone classification. We analyzed predictable factors for BMD preservation in the proximal femur and compared radiological remodeling of the femur and changes in BMD.

RESULTS

BMD at 5 years in zone 7 decreased less than 10%, whereas BMD in zone 1 increased to over the baseline (+ 1.9%). Multiple linear regression analyses revealed that body weight was a predictor for positive BMD change in the proximal femur. The frequency of radiolucency of the femur was significantly lower in patients who exhibited an increase in BMD at 5 years compared with BMD at 2 weeks in zone 7.

CONCLUSION

BMD preservation of the proximal femur after cemented collarless polished double-tapered stem implantation was more effective in heavier patients. Furthermore, the frequency of radiolucency around the stem was significantly lower in patients who exceeded 100% of the baseline BMD in zone 7 at 5 years.

Biomechanical behaviour of a French femoral component with thin cement mantle: The 'French paradox' may not be a paradox after all

Objective

Cement thickness of at least 2 mm is generally associated with more favorable results for the femoral component in cemented hip arthroplasty. However, French-designed stems have shown favorable outcomes even with thin cement mantle. The biomechanical behaviors of a French stem, Charnley-Marcel-Kerboull (CMK) and cement were researched in this study.

Methods

Six polished CMK stems were implanted into a composite femur, and one million times dynamic loading tests were performed. Stem subsidence and the compressive force at the bone-cement interface were measured. Tantalum ball (ball) migration in the cement was analyzed by micro CT

Results

The cement thickness of 95 % of the proximal and middle region was less than 2.5 mm. A small amount of stem subsidence was observed even with collar contact. The greatest compressive force was observed at the proximal medial region and significant positive correlation was observed between stem subsidence and compressive force. 9 of 11 balls in the medial region moved to the horizontal direction more than that of the perpendicular direction. The amount of ball movement distance in the perpendicular direction was 59 to 83% of the stem subsidence, which was thought to be slip in the cement of the stem. No cement defect and no cement breakage were seen.

Conclusion

Thin cement in CMK stems produced effective hoop stress without excessive stem and cement subsidence. Polished CMK stem may work like force-closed fixation in short-term experiment.

Cite this article: Y. Numata, A. Kaneuji, L. Kerboull, E. Takahashi, T. Ichiseki, K. Fukui, J. Tsujioka, N. Kawahara. Biomechanical behaviour of a French femoral component with thin cement mantle: The ‘French paradox’ may not be a paradox after all. Bone Joint Res 2018;7:485–493. DOI: 10.1302/2046-3758.77.BJR-2017-0288.R2.

The influence of cement thickness on stem subsidence and cement creep in a collarless polished tapered stem: When are thick cement mantles detrimental?

Objectives

Favourable results for collarless polished tapered stems have been reported, and cement creep due to taper slip may be a contributing factor. However, the ideal cement thickness around polished stems remains unknown. We investigated the influence of cement thickness on stem subsidence and cement creep.

Methods

We cemented six collarless polished tapered (CPT) stems (two stems each of small, medium and large sizes) into composite femurs that had been reamed with a large CPT rasp to achieve various thicknesses of the cement mantle. Two or three tantalum balls were implanted in the proximal cement in each femur. A cyclic loading test was then performed for each stem. The migration of the balls was measured three-dimensionally, using a micro-computed tomography (CT) scanner, before and after loading. A digital displacement gauge was positioned at the stem shoulder, and stem subsidence was measured continuously by the gauge. Final stem subsidence was measured at the balls at the end of each stem.

Results

A strong positive correlation was observed between mean cement thickness and stem subsidence in the CT slices on the balls. In the small stems, the balls moved downward to almost the same extent as the stem. There was a significant negative correlation between cement thickness and the horizontal:downward ratio of ball movement.

Conclusion

Collarless polished tapered stems with thicker cement mantles resulted in greater subsidence of both stem and cement. This suggests that excessive thickness of the cement mantle may interfere with effective radial cement creep.

Cite this article: E. Takahashi, A. Kaneuji, R. Tsuda, Y. Numata, T. Ichiseki, K. Fukui, N. Kawahara. The influence of cement thickness on stem subsidence and cement creep in a collarless polished tapered stem: When are thick cement mantles detrimental? Bone Joint Res 2017;6:–357. DOI: 10.1302/2046-3758.65.BJR-2017-0028.R1.

Complete bone remodeling after calcar reconstruction with metal wire mesh and impaction bone grafting: a case report

We report the histological findings of a reconstructed calcar region four years after femoral impaction bone grafting using metal wire mesh for a case with massive defect of the proximal part of the femur. Thin cortical bone was formed just beneath the metal wire mesh and viable trabecular bone containing a small amount of granulation tissue was observed even at the bone-cement interface. Almost no necrotic bone was seen throughout the remodeled bony layer. Histological findings of the present case suggest that calcar reconstruction with impaction bone grafting using a metal wire mesh is a biologically and mechanically favorable reconstruction method for femoral revision cases combined with proximal medial segmental cortex defect.

Impaction bone grafting for femoral revision hip arthroplasty with Exeter Universal stem in Japan

OBJECTIVES

The purpose of the present study was to analyze the retrospective clinical and radiographic results of femoral revision arthroplasties with impaction bone grafting performed by experienced Japanese surgeons.

PATIENTS AND METHODS

We investigated the radiographic and clinical records more than 2 years after the surgery in 99 hips of 93 patients. The average age was 66.3 years (36-84 years) and the average follow-up period was 5.2 years (2-13 years). The Merle d'Aubigné and Postel hip score was used for clinical assessment, and peri-operative fractures were recorded. The survival curve was estimated using Kaplan-Meier method.

RESULTS

The mean Merle d'Aubigné and Postel hip score improved from 9.0 points to 15.2 points at the final follow-up. Augmentations for segmental defect of femoral cortices were undertaken in 55 hips. Metal or strut allograft plates were applied to 9 hips and 21 hips, respectively. Intra-operative fractures or perforations occurred in 20 hips. Re-operations of the femur were undertaken in nine hips including five post-operative femoral fractures. More than 5 mm of subsidence was observed in only 2 hips. The survival rates at 8 years after the operation were 94.8 % with femoral fractures as the end point, 93.1 % with any stem removal or exchange as the end point, and 99.0 % with aseptic stem loosening as the end point, respectively.

CONCLUSION

The present study showed encouraging mid-term results of impaction bone grafting for femoral revision arthroplasty by experienced surgeons in Japan. Aggressive augmentation of segmental defects and attenuated femoral shafts prevents massive stem subsidence and periprosthetic fracture.

A comparison of subsidence of Exeter standard and long stems

The survivorship of the polished, double taper Exeter stem is related to subsidence within the cement mantle. Long Exeter stems have altered geometry which may influence subsidence characteristics. Using digitised x-rays and appropriate computer software we measured the subsidence of 35 standard and 40 long stem Exeter implants. Measurements were taken from initial postoperative radiographs and repeated at intervals up to 5 years. Long stem implants were used in cemented revisions without the use of impaction bone grafting. Subsidence rates of the standard length stems in our study were comparable to that in published literature. Long stems did not replicate this subsidence pattern and had subsided less at 6, 12 and 24 months. However, the 205mm long stem, which has a fully tapered design, did follow the subsidence characteristics of the standard stem. Subsidence of long stem Exeter implants does not mirror that of the standard length stem. Loss of the fully tapered geometry of the longer stem implants may account for this finding. We suggest that whenever possible, the 205mm long stem should be used if the biomechanical principles of the standard Exeter stem are to be utilised.