Effect of dipotassium phosphate addition and heat on proteins and minerals in milk protein beverages

Our objective was to determine the effects of dipotassium phosphate (DKP) addition, heat treatments (no heat, high temperature, short time [HTST]: 72°C for 15 s, and direct steam injection UHT: 142°C for 2.3 s), and storage time on the soluble protein composition and mineral (P, Ca, K) concentration of the aqueous phase around casein micelles in 7.5% milk protein-based beverages made with liquid skim milk protein concentrate (MPC) and micellar casein concentrate (MCC). Milk protein concentrate was produced using a spiral wound polymeric membrane, and MCC was produced using a 0.1-µm ceramic membrane by filtration at 50°C. Two DKP concentrations were used (0% and 0.15% wt/wt) within each of the 3 heat treatments. All beverages had no other additives and ran through heat treatment without coagulation. Ultracentrifugation (2-h run at 4°C) supernatants of the beverages were collected at 1, 5, 8, 12, and 15-d storage at 4°C. Phosphorus, Ca, and K concentrations in the beverages and supernatants were measured using inductively coupled plasma spectrometry. Protein composition of supernatants was measured using Kjeldahl and sodium dodecyl sulfate-PAGE. Micellar casein concentrate and MPC beverages with 0.15% DKP had higher concentrations of supernatant protein, Ca, and P than beverages without DKP. Protein, Ca, and P concentrations were higher in MCC supernatant than in MPC supernatant when DKP was added, and these concentrations increased over storage time, especially when lower heat treatments (HTST or no heat treatment) had been applied. Dipotassium phosphate addition caused the dissociation of αS-, β-, and κ-casein, and casein proteolysis products out of the casein micelles, and DKP addition explained over 70% of the increase in supernatant protein, P, and Ca concentrations. Dipotassium phosphate could be removed from 7.5% of protein beverages made with fresh liquid MCC and MPC (containing a residual lactose concentration of 0.6% to 0.7% and the proportional amount of soluble milk minerals), as these beverages maintain heat-processing stability without DKP addition.

Strategies for Exploiting Milk Protein Properties in Making Films and Coatings for Food Packaging: A Review

Biopolymers of different natures (carbohydrates, proteins, etc.) recovered from by-products of industrial processes are increasingly being studied to obtain biomaterials as alternatives to conventional plastics, thus contributing to the implementation of a circular economy. The food industry generates huge amounts of by-products and waste, including unsold food products that reach the end of their shelf life and are no longer usable in the food chain. Milk proteins can be easily separated from dairy waste and adapted into effective bio-based polymeric materials. Firstly, this review describes the relevant properties of milk proteins and the approaches to modifying them for subsequent use. Then, we provide an overview of recent studies on the development of films and coatings based on milk proteins and, where available, their applications in food packaging. Comparisons among published studies were made based on the formulation as well as production conditions and technologies. The role of different additives and modifiers tested for the performances of films and coatings, such as water vapor permeability, tensile strength, and elongation at break, were reviewed. This review also outlines the limitations of milk-protein-based materials, such as moisture sensitivity and brittleness. Overall, milk proteins hold great potential as a sustainable alternative to petroleum-based polymers. However, their use in food packaging materials at an industrial level remains problematic.

Manufacture of a novel cultured micellar casein concentrate ingredient for emulsifying salt free process cheese products applications

Micellar casein concentrate (MCC) is a high protein ingredient that is typically produced using 3 stages of microfiltration with a 3× concentration factor and diafiltration. Acid curd is an acid protein concentrate, which can be obtained by precipitating the casein at pH 4.6 (isoelectric point) using starter cultures or direct acids without the use of rennet. Process cheese product (PCP) is a dairy food prepared by blending dairy ingredients with nondairy ingredients and then heating the mixture to get a product with an extended shelf-life. Emulsifying salts are critical for the desired functional characteristics of PCP because of their role in calcium sequestration and pH adjustment. The objectives of this study were to develop a process to produce a novel cultured micellar casein concentrate ingredient (cMCC; culture-based acid curd) and to produce PCP without emulsifying salts using different combinations of protein from cMCC and MCC in the formulations (2.0:1.0, 1.9:1.1, and 1.8:1.2). Skim milk was pasteurized at 76°C for 16 s and then microfiltered in 3 microfiltration stages using graded permeability ceramic membranes to produce liquid MCC (11.15% total protein; TPr and 14.06% total solids; TS). Part of the liquid MCC was spray dried to produce MCC powder (75.77% TPr and 97.84% TS). The rest of the MCC was used to produce cMCC (86.9% TPr and 96.4% TS). Three PCP treatments were formulated with different ratios of cMCC:MCC, including 2.0:1.0, 1.9:1.1, and 1.8:1.2 on the protein basis. The composition of PCP was targeted to 19.0% protein, 45.0% moisture, 30.0% fat, and 2.4% salt. This trial was repeated 3 times using different batches of cMCC and MCC powders. All PCP were evaluated for their final functional properties. No significant differences were detected in the composition of PCP made with different ratios of cMCC and MCC except for the pH. The pH was expected to increase slightly with elevating the MCC amount in the PCP formulations. The end apparent viscosity was significantly higher in 2.0:1.0 formulation (4,305 cP) compared with 1.9:1.1 (2,408 cP) and 1.8:1.2 (2,499 cP). The hardness ranged from 407 to 512 g with no significant differences within the formulations. However, the melting temperature showed significant differences with 2.0:1.0 having the highest melting temperature (54.0°C), whereas 1.9:1.1 and 1.8:1.2 showed 43.0 and 42.0°C melting temperature, respectively. The melting diameter (38.8 to 43.9 mm) and melt area (1,183.9 to 1,538.6 mm²) did not show any differences in different PCP formulations. The PCP made with a 2.0:1.0 ratio of protein from cMCC and MCC showed better functional properties compared with other formulations.

pH-dependent sedimentation and protein interactions in ultra-high-temperature-treated sheep skim milk

Sheep milk is considered unstable to UHT processing, but the instability mechanism has not been investigated. This study assessed the effect of UHT treatment (140°C/5 s) and milk pH values from 6.6 to 7.0 on the physical properties of sheep skim milk (SSM), including heat coagulation time, particle size, sedimentation, ionic calcium level, and changes in protein composition. Significant amounts of sediment were found in UHT-treated SSM at the natural pH (∼6.6) and pH 7.0, whereas lower amounts of sediment were observed at pH values of 6.7 to 6.9. The proteins in the sediment were mainly κ-casein (CN)-depleted casein micelles with low levels of whey proteins regardless of the pH. Both the pH and the ionic calcium level of the SSM at all pH values decreased after UHT treatment. The dissociation levels of κ-, β-, and α_S2-CN increased with increasing pH of the SSM before and after heating. The protein content, ionic calcium level, and dissociation level of κ-CN were higher in the SSM than values reported previously in cow skim milk. These differences may contribute to the high amounts of sediment in the UHT-treated SSM at natural pH (∼6.6). Significantly higher levels of κ-, β-, and α_S2-CN were detected in the serum phase after heating the SSM at pH 7.0, suggesting that less κ-CN was attached to the casein micelles and that more internal structures of the casein micelles may have been exposed during heating. This could, in turn, have destabilized the casein micelles, resulting in the formation of protein aggregates and high amounts of sediment after UHT treatment of the SSM at pH 7.0.

Calcium-Reduced Micellar Casein Concentrate-Physicochemical Properties of Powders and Functional Properties of the Dispersions

This study aimed to examine the physicochemical properties of 30% calcium (Ca)-reduced micellar casein 80% protein powders (RC-MCC) and the functional properties of the resultant dispersions. The calcium reduction in the micellar casein (MCC) powder was achieved by subjecting the liquid micellular casein obtained from the microfiltration of pasteurized skim milk to carbon dioxide (CO2) treatment before and during ultrafiltration. The CO2 injection was controlled to obtain a 0 and 30% reduction in calcium in the C-MCC (control) and RC-MCC powders, respectively. The MCC powders were tested for physicochemical properties such as chemical composition, particle size distribution, and bulk density. The MCC powders were reconstituted in deionized water to test the functional properties of the dispersions, i.e., solubility, viscosity, heat stability, emulsifying capacity, emulsion stability, foam capacity, and foam stability. The CO2 injection did not result in any significant differences in the composition except mineral contents, particularly calcium. The particle size and bulk density of RC-MCC powders were significantly (p < 0.05) lower than control powders. The RC-MCC powder dispersions showed increased heat stability compared to control, whereas no significant changes in viscosity and emulsification capacity were observed between the two dispersions. However, the emulsion stability and foam stability of RC-MCC dispersions were significantly lower than C-MCC dispersions. This study showed that by utilizing a novel microfiltration−CO2 injection−ultrafiltration process, 30% calcium-reduced MCC powder was commercially feasible. This research also provides a detailed understanding of the effect of calcium reduction on the functional properties of resultant MCC dispersions. It showed that calcium reduction could improve the solubility of the powders and heat stability and foam capacity of the dispersions.

Compositional and Functional Characteristics of Feta-Type Cheese Made from Micellar Casein Concentrate

Micellar casein concentrate (MCC) is a high protein ingredient (obtained by microfiltration of skim milk) with an elevated level of casein as a percentage of total protein (TP) compared to skim milk. It can be used as an ingredient in cheese making. Feta-type cheese is a brined soft cheese with a salty taste and acid flavor. We theorize that Feta-type cheese can be produced from MCC instead of milk, which can improve the efficiency of manufacture and allow for the removal of whey proteins before manufacturing Feta-type cheese. The objectives of this study were to develop a process of producing Feta-type cheese from MCC and to determine the optimum protein content in MCC to make Feta-type cheese. MCC solutions with 3% (MCC-3), 6% (MCC-6), and 9% (MCC-9) protein were prepared and standardized by mixing water, MCC powder, milk permeate, and cream to produce a solution with 14.7% total solids (TS) and 3.3% fat. Thermophilic cultures were added at a rate of 0.4% to MCC solutions and incubated at 35 °C for 3 h to get a pH of 6.1. Subsequently, calcium chloride and rennet were added to set the curd in 20 min at 35 °C. The curd was then cut into cubes, drained for 20 h followed by brining in 23% sodium chloride solutions for 24 h. Compositional analysis of MCC solutions and cheese was carried out. The yield, color, textural, and rheological measurements of Feta-type cheese were evaluated. Feta-type cheese was also made from whole milk as a control. This experiment was repeated three times. The yield and adjusted yield of Feta-type cheese increased from 19.0 to 54.8 and 21.4 to 56.5, respectively, with increasing the protein content in MCC from 3% to 9%. However, increasing the protein content in MCC did not show significant differences in the hardness (9.2-9.7 kg) of Feta-type cheese. The color of Feta-type cheese was less white with increasing the protein content in MCC. While the yellowish and greenish colors were high in Feta-type cheese made from MCC with 3% and 6% protein, no visible differences were found in the overall cheese color. The rheological characteristics were improved in Feta-type cheese made from MCC with 6% protein. We conclude that MCC with different levels of protein can be utilized in the manufacture of Feta-type cheese.

Progress in micellar casein concentrate: Production and applications

Micellar casein concentrate (MCC) is a novel ingredient with high casein content. Over the past decade, MCC has emerged as one of the most promising dairy ingredients having applications in beverages, yogurt, cheese, and process cheese products. Industrially, MCC is manufactured by microfiltration (MF) of skim milk and is commercially available as a liquid, concentrated, or dried containing ≥9, ≥22, and ≥80% total protein, respectively. As an ingredient, MCC not only imparts a bland flavor but also offers unique functionalities such as foaming, emulsifying, wetting, dispersibility, heat stability, and water-binding ability. The high protein content of MCC represents a valuable source of fortification in a number of food formulations. For the last 20 years, MCC is utilized in many applications due to the unique physiochemical and functional characteristics. It also has promising applications to eliminate the cost of drying by producing concentrated MCC. This work aims at providing a succinct overview of the historical progress of the MCC, a review on the manufacturing methods, a discussion of MCC properties, varieties, and applications.

In vitro screening of technical lignins to determine their potential as hay preservatives

Our objectives were to evaluate technical lignins for their antifungal properties against 3 molds and 1 yeast causing hay spoilage, and their ability to preserve ground high-moisture alfalfa hay nutritive value in vitro. In experiment 1, 8 technical lignins and propionic acid (PRP; positive control) were tested at a dose of 40 mg/mL. The experiment had a randomized complete block design (RCBD, 4 runs) and a factorial arrangement of 3 molds × 10 additives (ADV). The effects of the ADV on yeast were evaluated separately with a RCBD. Sodium lignosulfonate (NaL) and PRP were the only treatments with 100 ± 2.8% inhibition of fungi. In experiment 2, the minimum inhibitory concentration (MIC) for selected lignins and PRP were determined. At pH 4, NaL had the lowest MIC across the molds (20-33.3 mg/mL) and magnesium lignosulfonate (MgL) for the yeast (26.7) among the lignins. However, PRP had MIC values that were several-fold lower across all fungi (1.25-3.33). In experiment 3, a RCBD (5 blocks) with a 3 (ADV; NaL, MgL, and PRP) × 4 (doses: 0, 0.5, 1, and 3% wt/wt fresh basis) factorial arrangement of treatments was used to evaluate the preservative effects of ADV in ground high-moisture alfalfa hay inoculated with a mixture of the fungi previously tested and incubated under aerobic conditions in vitro. After 15 d, relative to untreated hay (14.9), dry matter (DM) losses were lessened by doses as low as 1% for NaL (3.39) and 0.5% for PRP (0.81 ± 0.77%). The mold count was reduced in both NaL at 3% (3.92) and PRP as low as 0.5% (3.94) relative to untreated hay (7.76 ± 0.55 log cfu/fresh g). Consequently, sugars were best preserved by NaL at 3% (10.1) and PRP as low as 0.5% (10.5) versus untreated (7.99 ± 0.283% DM), while keeping neutral detergent fiber values lower in NaL (45.9) and PRP-treated (45.1) hays at the same doses, respectively, relative to untreated (49.7 ± 0.66% DM). Hay DM digestibility was increased by doses as low as 3% for NaL (67.5), 1% MgL (67.0), and 0.5% PRP (68.5) versus untreated hay (61.8 ± 0.77%). The lowest doses increasing neutral detergent fiber digestibility relative to untreated hay (23.3) were 0.5% for MgL and PRP (30.5 and 30.1, respectively) and 1% for NaL (30.7 ± 1.09% DM). Across technical lignins, NaL showed the most promise as a potential hay preservative. However, its effects were limited compared with PRP at equivalent doses. Despite not having an effect on preservation, MgL improved DM digestibility by stimulating neutral detergent fiber digestibility. This study warrants further development of NaL under field conditions.

A comparison of the heat stability of fresh milk protein concentrates obtained by microfiltration, ultrafiltration and diafiltration

The objective of this work was to evaluate the impact of changes during membrane filtration on the heat stability of milk protein concentrates. Dairy protein concentrates have been widely employed in high protein drinks formulations and their stability to heat treatment is critical to ensure quality of the final product. Pasteurized milk was concentrated three-fold by membrane filtration, and the ionic composition was modified by addition of water or permeate from filtration (diafiltration). Diafiltration with water did not affect the apparent diameter of the casein micelles, but had a positive effect on heat coagulation time (HCT), which was significantly longer (50 min), compared to the non diafiltered concentrates (about 30 min). UHT treatments increased the particle size of the casein micelles, as well as the turbidity of retentates. Differences between samples with and without diafiltration were confirmed throughout further analysis of the protein composition of the unsedimentable fraction, highlighting the importance of soluble protein composition on the processing functionality of milk concentrates.

In vitro effect of multiple hydrogen peroxide gas plasma sterilizations on the rate of closure of ameroid constrictors

OBJECTIVE

To evaluate the effect of multiple hydrogen peroxide gas plasma (HPGP) sterilizations on the rate of closure of ameroid constrictors.

SAMPLE

Thirty-six 5.0-mm ameroid constrictors.

PROCEDURES

Ameroid constrictors were randomly allocated to 6 groups. Each group underwent 1, 2, 3, 4, 5, or 6 HPGP sterilizations. Ameroid constrictors were then incubated for 35 days in canine plasma and digitally imaged at predetermined times during incubation. One individual, who was unaware of the group to which each ameroid constrictor was assigned, measured the lumen area of the constrictor on each digital image. Mean lumen area was compared among groups.

RESULTS

No ameroid constrictors were completely closed after 35 days of incubation in canine plasma. Mean lumen area after incubation did not differ among constrictors that underwent 1, 2, and 3 sterilizations. Constrictors that underwent 4 sterilizations were closed significantly more than were those that underwent 1, 2, or 3 sterilizations. Mean lumen area after incubation did not differ significantly between constrictors that underwent 5 and 6 sterilizations, although the final lumen areas for those constrictors were significantly smaller than those for constrictors that underwent 1, 2, 3, and 4 sterilizations.

CONCLUSIONS AND CLINICAL RELEVANCE

Ameroid constrictors that underwent 5 and 6 HPGP sterilizations had a 9% to 12% decrease in lumen area, compared with that of constrictors that underwent ≤ 4 plasma sterilizations, and the use of such constrictors could increase the risk of portal hypertension and secondary acquired shunting or decrease the risk of persistent shunting.