The biomechanical analysis of three-dimensional distal radius fracture model with different fixed splints

Identification of excessive contact pressures under hand orthosis based on finite element analysis

BACKGROUND

Implicit magnitudes and distribution of excessive contact pressures under hand orthoses hinder clinicians from precisely adjusting them to relieve the pressures. To address this, contact pressure under a hand orthosis were analysed using finite element method.

METHODS

This paper proposed a method to numerically predict the relatively high magnitudes and critical distribution of contact pressures under hand orthosis through finite element analysis, to identify excessive contact pressure locations. The finite element model was established consisting of the hand, orthosis and bones. The hand and bones were assumed to be homogeneous and elastic bodies, and the orthosis was considered as an isotropic and elastic shell. Two predictions were conducted by assigning either low (fat) or high (skin) material stiffness to the hand model to attain the range of pressure magnitudes. An experiment was conducted to measure contact pressures at the predicted pressure locations.

RESULTS

Identical pressure distributions were obtained from both predictions with relatively high pressure values disseminated at 12 anatomical locations. The highest magnitude was found at the thumb metacarpophalangeal joint with the maximum pressure range from 13 to 78 KPa. The measured values were within the predicted range of pressure magnitudes. Moreover, 6 excessive contact pressure locations were identified.

CONCLUSIONS

The proposed method was verified by the measurement results. It renders understanding of interface conditions underneath the orthosis to inform clinicians regarding orthosis design and adjustment. It could also guide the development of 3D printed or sensorised orthosis by indicating optimal locations for perforations or pressure sensors.

Three‑dimensional finite element analysis: Anatomical splint fixation for Colles fractures

With the rapid development of digital research in clinical orthopedics, the efficacy and safety of splint fixation can be better evaluated through biomechanical analysis based on a three-dimensional (3D) finite element model. It is essential to address the current gap in understanding the biomechanical implications of anatomical splint fixation for Colles fractures. By employing advanced 3D finite element analysis, the present study aimed to provide a comprehensive evaluation, offering valuable insights that can contribute to enhancing the effectiveness of anatomical splint fixation in the clinical management of Colles fractures. The 3D finite element models of the forearm and hand were constructed using Mimics 15.0 according to data from computed tomography of a patient with a Colles fracture. After the validity of the model was verified, the corresponding material properties of the models were adjusted to simulate a Colles fracture. Subsequently, the reduction functions, such as radial inclination and ulnar deviation, of the simulated fracture were completed and the mechanical changes of the tissues surrounding the fracture were calculated. Anatomical splints were then placed on the surfaces of the 3D finite element models of Colles fractures at various positions to analyze the changes in the stress cloud diagram, such as for the soft tissue and anatomical splints. In the present study, the constructed 3D finite element models were accurate and valid. The maximum stress of the anatomical splints and soft tissues was 2.346 and 0.106 MPa in pronation, 1.780 and 0.069 MPa in median rotation and 3.045 and 0.057 MPa in supination, respectively. Splint stress reached the highest level in supination and soft tissue stress achieved the highest level in pronation. The peak of splint stress occurred during supination, which contrasts to the peak of soft tissue stress observed in pronation, suggesting splint fixation median rotation can effectively avoid compression of the local soft tissue.

An optimal de Quervain's tenosynovitis splint with ergonomic thumb support and evenly distributed pressure

Splinting is a conventional treatment for de Quervain's tenosynovitis (dQt). However, existing splints have problems such as excessive thermal discomfort and poor fit, which have been pointed out in previous studies. This study proposes a new functional splint consisting of both hard and soft materials with the aim of providing wear comfort with a good fit and sufficient stability of the injured hand. Thumb support of the splint is an important component that controls and protects the affected thumb. To develop an ergonomically shaped thumb support, 16 participants with dQt were recruited for three-dimensional (3D) scanning of their hands. The angles of the wrist and the curvature of the thumb were measured using computer software, and the results were used as a reference for the design of the prototype supports. Excessive pressure on particular regions, such as bony areas, may cause discomfort or pain. To ensure the wear comfort of the proposed splint, a finite element model (FEM) was built to simulate the wear process of the splint and hence to predict the pressure distribution exerted from the splint onto the hand of the wearer. The simulated results show that the pressure is evenly distributed over the hand, indicating that patients are likely to wear the proposed splint comfortably during their treatment period.

Wearable rehabilitation wristband for distal radius fractures

Background

Distal radius fractures are a common type of fracture. For patients treated with closed reduction with splinting, a period of rehabilitation is still required after the removal of the splint. However, there is a general lack of attention and low compliance to rehabilitation training during this period, so it is necessary to build a rehabilitation training monitoring system to improve the efficiency of patients' rehabilitation.

Methods

A wearable rehabilitation training wristband was proposed, which could be used in the patient's daily rehabilitation training scenario and could recognize four common wrist rehabilitation actions in real-time by using three thin film pressure sensors to detect the pressure change curve at three points on the wrist. An algorithmic framework for classifying rehabilitation training actions was proposed. In our framework, an action pre-detection strategy was designed to exclude false detections caused by switching initial gestures during rehabilitation training and wait for the arrival of the complete signal. To classify the action signals into four categories, firstly an autoencoder was used to downscale the original signal. Six SVMs were then used for evaluation and voting, and the final action with the highest number of votes would be used as the prediction result.

Results

Experimental results showed that the proposed algorithmic framework achieved an average recognition accuracy of 89.62%, an average recognition recall of 88.93%, and an f1 score of 89.27% on the four rehabilitation training actions.

Conclusion

The developed device has the advantages of being small size and easy to wear, which can quickly and accurately identify and classify four common rehabilitation training actions. It can easily be combined with peripheral devices and technologies (e.g., cell phones, computers, Internet) to build different rehabilitation training scenarios, making it worthwhile to use and promote in clinical settings.

Improvement, Validation, and Analysis of Colles Fracture Treated with an Integrated Retainer Pad Splint

Objective

To observe the effectiveness and safety of the Colles fracture treated with the integrated retainer pad splint and to compare the clinical and radiological outcomes of the integrated retainer pad splint and the traditional bamboo curtain splint in the treatment of the Colles fracture.

Methods

A total of 100 patients with Colles fractures were randomly divided into two groups: the treatment group was fixed with the integrated retainer pad splint (IS), and the control group was fixed with the traditional bamboo curtain splint (TS).The range of wrist motion was measured at follow-up examinations, and volar inclination, ulnar deviation, and radial height were measured on radiographs. Regular follow-up wrist imaging examinations and functional examinations were performed before reduction, after reduction, and at the 1st, 3rd, 5^th, and 8th weeks. The two groups were compared in terms of convenience, fracture healing time, X-ray data of volar inclination, ulnar deviation, radial height, and wrist joint function. The relevant data were analyzed with SPSS 25.0 statistical software.

Results

There were no notable differences in gender, age, and injured side between IS and TS groups. In terms of operation time, IS was better than the TS group (P < 0.05), and the operation time in the IS group was shorter. On the basis of X-ray data of volar inclination, ulnar deviation, and radial height measured on radiographs, the difference between the IS and TS groups was statistically significant (P < 0.05), which showed that the IS group was more stable in fracture fixation and had less reduction loss during the treatment process. At the 8th week of treatment, the wrist Gartland–Werley score of the two groups showed that the two fixation methods are equivalent in restoring wrist joint function (P > 0.05); however, in terms of the excellent and good rate of wrist joint function, the IS group scored 96% was higher than the TS group (80%).

Conclusion

Compared with the traditional bamboo curtain splint, the integrated retainer pad splint is more convenient and stable, and it has less reduction loss during the treatment. Repair of the Colles fracture using the integrated retainer pad splint with external fixation results in nearly normal return of function, which is significantly better than using the traditional bamboo curtain splint.