A computed tomography-based anatomic comparison of three different types of c7 posterior fixation techniques : pedicle, intralaminar, and lateral mass screws

Finite Element Analysis Comparing the Biomechanical Parameters in Multilevel Posterior Cervical Instrumentation Model Involving Lateral Mass Screw versus Transpedicular Screw Fixation at the C7 Vertebra

STUDY DESIGN

Basic research.

PURPOSE

This finite element (FE) analysis (FEA) aimed to compare the biomechanical parameters in multilevel posterior cervical fixation with the C7 vertebra instrumented by two techniques: lateral mass screw (LMS) vs. transpedicular screw (TPS).

OVERVIEW OF LITERATURE

Very few studies have compared the biomechanics of different multilevel posterior cervical fixation constructs.

METHODS

Four FE models of multilevel posterior cervical fixation were created and tested by FEA in various permutations and combinations. Generic differences in fixation were determined, and the following parameters were assessed: (1) maximum moment at failure, (2) maximum angulation at failure, (3) maximum stress at failure, (4) point of failure, (5) intervertebral disc stress, and (6) influence of adding a C2 pars screw to the multilevel construct.

RESULTS

The maximum moment at failure was higher in the LMS fixation group than in the TPS group. The maximum angulation in flexion allowed by LMS was higher than that by TPS. The maximum strain at failure was higher in the LMS group than in the TPS group. The maximum stress endured before failure was higher in the TPS group than in the LMS group. Intervertebral stress levels at C6-C7 and C7-T1 intervertebral discs were higher in the LMS group than in the TPS group. For both models where C2 fixation was performed, lower von Mises stress was recorded at the C2-C3 intervertebral disc level.

CONCLUSIONS

Ending a multilevel posterior cervical fixation construct with TPS fixation rather than LMS fixation at the C7 vertebra provides a stiff and more constrained construct system, with higher stress endurance to compressive force. The constraint and durability of the construct can be further enhanced by adding a C2 pars screw in the fixation system.

A Computed Tomography Study of the C7 Vertebra Screws Fixation in Children

STUDY DESIGN

Retrospective analysis of computed tomographic images of 92 normal pediatric cervical vertebrae.

OBJECTIVE

The aim of this study was to ascertain the feasibility of the pedicle, intralaminar, and lateral mass screws fixation in children.

SUMMARY OF BACKGROUND DATA

Fixation techniques of C7 vertebrae are technically challenging in the pediatric population. Although the techniques offer alternatives to screws placement at C7 spine in adult, there is no consensus to apply these screws in children.

METHODS

A total of 92 patients (59 males and 33 females) from 3- to 16-year old divided into three groups (group 1, 1-6 years; group2, 7-10 years; group 3, 11-16 years) were included. Measurements were taken through computed tomography (CT) imaging without evidence of spinal trauma. Length, width, and angle of lamina and pedicle were measured, and lateral mass length was also assessed.

RESULTS

There was no statistical difference between the left and right sides, as well as the sexes. In 1 to 6 years' age group, 83.3% of the laminas and 87.5% of the pedicles measured have thicknesses of >3.5 mm. In 7 to 10 years' age group, 84.0% of the laminas and all the pedicles observed have thicknesses of >3.5 mm. In 11 to 16 years' age group, 88.4% of the laminas and 97.7% of the pedicles measured have thicknesses of >3.5 mm. Most of the spinolaminar angles were between 42.5° and 56°. There are three cases (3.3%) having lateral mass length >12 mm.

CONCLUSION

It is feasible to insert a screw (Ø 3.5 mm) in C7 lamina in children, and the intralaminar screw fixation is a safe and reliable technique. Around 49°, the spinolaminar angle with axial position, can be used as reference for placing screws in the C7 lamina. Preoperative CT scan will help surgeons to insert the laminar screw safely and accurately.

LEVEL OF EVIDENCE

N/A.

Comparison of Three Different Options for C7 Posterior Vertebral Anchor in the Indian Population-Lateral Mass, Pedicle, and Lamina: A Computed Tomography-Based Morphometric Analysis

Study Design

Radiological cohort study.

Purpose

The options of posteriorly stabilizing C7 vertebra include using lateral mass, pedicle or lamina, as bony anchors. The current study is a computed tomography (CT)-based morphometric analysis of C7 vertebra of 100 Indian patients and discusses the feasibility of these different techniques.

Overview of Literature

C7 is a peculiar vertebra with unique anatomy, which poses challenges for each of these fixation modalities. There are no reports available in the literature, which discuss and compare the feasibility of diverse posterior C7 fixation techniques in Indian population.

Methods

We included 100 consecutive cervical spine CT scans of Indian patients performed between July 2016 and September 2016. We excluded CT scans with any significant congenital anomaly or other pathological lesions of C7 and patients with non-Indian ethnicity. Regarding screw placement, we assessed and studied various dimensions of the C7 lateral mass, pedicles, and laminae in relevant sections.

Results

The mean age of our patients was 49.5±16.1 years. We included 56 male and 44 female patients. The mean anteroposterior and mediolateral dimensions of the lateral mass were 11.38±1.76 and 12.91±1.82 mm, respectively. The mean length of the lateral mass screw (Magerl technique) was 12.17±1.9 mm; 92% of patients could accommodate a lateral mass screw at least 10-mm long (unicortical), whereas 48% could accommodate a screw (unicortical) longer than 12 mm. Foramen transversarium was found in 30.5% of lateral masses. The mean outer and inner cortical widths of the pedicles were 6.5±0.71 mm and 3.72±0.61 mm, respectively. Approximately 58% of pedicles could accommodate 3.5-mm screws (based on the inner cortical pedicle width). The outer cortical and inner cortical widths of the laminae were 6.21±1.2 mm and 3.23±0.9 mm, respectively. Subsequently, 37% of the laminae could accommodate 3.5-mm screws. The mean angle of intralaminar screw trajectory was 50.7°±5.1°, and the mean length of the intralaminar screw was 32.6±3.05 mm. In addition, 96.4% and 60.7% of male patients could accommodate lateral mass screws longer than 10 mm and 12 mm, respectively. However, only 86.4% and 31.8% of female patients could accommodate 10- and 12-mm long lateral mass screws, respectively. Furthermore, 75% of male patients and 36% of female patients had pedicles that could accommodate 3.5-mm diameter screws, and 48.2% of male patients had laminae that could accommodate 3.5-mm screws; however, only 22.7% of female patients could accommodate 3.5-mm laminar screws.

Conclusions

Based on our CT-guided morphometric analysis, 92% and 48% of Indian patients could accommodate at least 10- and 12-mm long lateral mass screws, and 58% of pedicles and 37% of laminae could accommodate 3.5-mm screws. Thus, lateral mass screws (between 10- and 12-mm long) seem to be the safest feasible option for C7 fixation. In case of the need for an alternative mode of stabilization (pedicle or intralaminar screw), particularly in female patients, careful preoperative planning with a CT scan is of utmost importance.

C7 intra-laminar screws for complex cervicothoracic spine surgery-a case series

Background

C7 has relatively unique anatomy compared to the remainder of the subaxial cervical spine (C3-C6) and upper thoracic spine. The C7 laminar has been previously reported in feasibility and biomechanical studies as an adequate fixation point in contrast to the lateral mass or pedicles, with few reports of its use in clinical practice. The purpose of this study was to review the safety and efficacy of using the C7 laminar as a fixation point in constructs involving the cervical spine and cervicothoracic junction.

Methods

Between February 2013 and July 2016, 10 patients (6 males, 4 females) had 19 C7 intra-laminar screws sited (bilateral in 9 patients, unilateral in 1 patient). Six patients had trauma as an underlying etiology, 2 of which had pseudoarthrosis from prior surgery. Three patients had cervical myelopathy from degenerative disease, 2 of which required anterior and posterior instrumentation for correction of deformity and 1 which had stand-alone posterior fixation. One patient had stabilization for an underlying malignancy.

Results

One patient died 2 weeks following their high cervical injury secondary to complications of respiratory failure. None of the remaining 9 patients were noted to have construct failure at a median follow up of 1 year (range, 6 months to 4 years) and all were noted to have satisfactory positioning of the instrumentation on post-operative imaging. The patient with malignancy died 6 months later from extra-spinal disease, there was one wound breakdown requiring debridement without infection in a revision case, and one patient required laminectomy for post-traumatic syrinx formation.

Conclusions

The C7 laminar provides an alternative fixation point for constructs involving the subaxial cervical spine and cervicothoracic junction, with excellent safety and efficacy in this small series. Larger series are required to more clarify the risk profile of this technique.

Quantitative Anatomy of C7 Vertebra in Southern Chinese for Insertion of Lateral Mass Screws and Pedicle Screws

Study Design

Retrospective study.

Purpose

To analyze the quantitative anatomy of C7 vertebra for insertion of lateral mass screws and pedicle screws in Southern Chinese patients.

Overview of Literature

C7 lateral mass is smaller when compared to other subaxial cervical levels, which limits the length of lateral mass screws that can be used. Some studies have suggested pedicle screws for better fixation. But, this option is limited by the narrow pedicle width.

Methods

We have obtained computed tomography (CT) cervical spine data in 0.625 mm slices from our radiology department. The patients were adults. CTs were from May to August, 2015. The lateral mass screw length was measured using Margerl's technique and pedicle width and pedicle screw trajectory were determined in three-dimensional reformated images.

Results

CT scans of cervical spines of 94 patients were obtained and 188 lateral masses and pedicles of C7 vertebrae were measured. The mean lateral mass screw length was 13.2 mm (standard deviation [SD] 1.6 mm), mean outer pedicle width was 5.9 mm (SD 1.0 mm) and mean pedicle screw trajectory was 29.4 degrees (SD 3.6 degrees). Most (91.0%) of the pedicles had an outer diameter ≥4.5 mm.

Conclusions

The mean lateral mass screw length was longer when compared with other similar studies, while the mean outer pedicle width was narrower. Nearly 10% of the pedicles were unable to accommodate 3.5 mm screws. These findings favor the use of lateral mass screws to provide a safe and stable fixation for C7 vertebrae in Southern Chinese patients, while the final choice of fixation method should only be confirmed after careful preoperative planning with CT scan.

FREE-HAND PLACEMENT OF C7 PEDICLE SCREWS: A CADAVERIC STUDY

Objective : To evaluate the accuracy of free-hand pedicle screws placement at the seventh cervical vertebra. Methods : The authors have exposed the cervicothoracic junction of 9 adult cadavers (7 male and 2 female) preserved in formalin from the Faculty of Medicine of the Universidad Andina Néstor Cáceres Velásquez, city of Juliaca, Puno - Peru, locating the C7 vertebra based on anatomical parameters. According to previous publications, the entry point for the C7 pedicle was determined as 3-4mm lateral and 5-6mm superior to the center of the lateral mass, and the pedicle was drilled manually and instrumented with 3.5mm screws. After the screws placement, the C7 vertebrae were removed for radiographic analysis. Results : The authors were able to adequately locate the C7 entry point in 12 pedicles (66.6% accuracy), finding a great variability both laterally (2-5mm) and cranially (3-10mm). The angulation in the coronal plane was correct in 13 pedicles (72.3%), despite the incorrect location of the entry point. Angle values in the coronal plane ranged from 38 to 62 degrees. In the sagittal plane angulation, 2 screws were placed in the C6-C7 disc. The midtransversal diameter of the 18 pedicles ranged from 4 to 7mm. Conclusions : The location of the entry point for placement of C7 pedicle screws with pure free-hand technique is very variable due to anatomical differences and the authors recommend some type of guidance for increased safety and accuracy.

Radiological anatomy of the C7 vertebra: Clinical implications in spine surgery

Context:

This study was designed to understand and define the special radio-anatomic morphometry of C7 vertebra by using multidetector computed tomography (MDCT).

Aims:

The major aim of the study was to detect the gender- and side-related morphometric differences of C7 vertebra among subjects.

Setting and design:

Our radiology unit database scanned for MDCT sections of the C7 vertebra.

Materials and Methods:

A total of 214 patients (134 men, 80 women) were selected. A detailed morphometric evaluation of C7 was done.

Statistical analysis used:

T test, ANOVA. Lamina length (P < 0.001), pedicle length (P < 0.001), outer cortical (P = 0.01) and inner cancellous pedicle (P < 0.001) width, pedicle angle to sagittal plane (P < 0.001) values were statistically significantly different on the right versus left side. When the results were stratified by gender, lamina length, inner cancellous lamina height, pedicle length, inner cancellous pedicle height, outer cortical pedicle width, lateral mass anteroposterior length, anteroposterior length of C7 corpus, height of C7 corpus (P < 0.001), C6-7 (P = 0.013) and C7-T1disc height (P = 0.04), transverse foramina perpendicular width at C7 (P = 0.046) values were found to be statistically significantly different. Vertebral artery most commonly enters into the transverse foramina at C6 level.

Conclusions:

Gender and side differences are important factors for preoperative planning and showed significant differences among subjects. MDCT is a practical option for investigating the exact anatomical features of osseous structures.

Feasibility of translaminar screw placement in Korean population: morphometric analysis of cervical spine

PURPOSE

To analyze the feasibility of unilateral and bilateral translaminar screw placement in Koran population, and compare the acceptance rate using previously reported data in American population.

MATERIALS AND METHODS

The translaminar lengths, thickness, heights, and sagittal-diagonal measurements were performed. The feasibility analysis was performed using unilateral and bilateral 3.5 mm cervical screw placement on the CT scans within 0.5 mm of safety margin. We also performed radiographic analysis of the morphometric dimensions and the feasibility of unilateral and bilateral translaminar screw placement at C3-C7.

RESULTS

Korean population had similar or significantly shorter translaminar lengths and thickness (lengths and thickness in C7 among males; lengths in C6-C7 and thickness in C4 among females) than American population, but had similar or significantly longer translaminar heights and sagittal-diagonal measurements (heights in C3-C7 and sagittal-diagonal measurements in C3-C6 among males; heights in C7 and sagittal-diagonal measurements in C3-C7 among females). Unilaterally, translaminar screw acceptance rates in C3-C7 were similar between Korean and American male population, but the rates in C4-C6 were significantly smaller between Korean and American female population. Bilaterally, translaminar screw acceptance rates in C3 and C5-C6 were significantly larger between Korean and American male population, but the rates in C3-C7 were similar between Korean and American female population.

CONCLUSION

The feasibility of unilateral and bilateral translaminar screw placement is different depending on different ethnics. Subaxial cervical unilateral translaminar screw placement among Korean male population and bilateral placement at C4-C7 among Korean female population are more acceptable than American population.

Feasibility of bilateral crossing c7 intralaminar screws: a cadaveric study

Objective

When the pedicle screw insertion technique is failed or not applicable, C7 intralaminar screw insertion method has been used as an alternative or salvage fixation method recently. However, profound understanding of anatomy is required for safe application of the bilaterally crossing laminar screw at C7 in clinic. In this cadaveric study, we evaluated the anatomic feasibility of the bilateral crossing intralaminar screw insertion and especially focused on determination of proper screw entry point.

Methods

The C7 vertebrae from 18 adult specimens were studied. Morphometric measurements of the mid-laminar height, the minimum laminar thickness, the maximal screw length, and spino-laminar angle were performed and cross-sectioned vertically at the screw entry point (spino-laminar junction). The sectioned surface was equally divided into 3 parts and maximal thickness and surface area of the parts were measured. All measurements were obtained bilaterally.

Results

The mean mid-laminar height was 13.7 mm, mean minimal laminar thickness was 6.6 mm, mean maximal screw length was 24.6 mm, and mean spinolaminar angle was 50.8±4.7°. Based on the measured laminar thickness, the feasibility of 3.5 mm diameter intralaminar screw application was 83.3% (30 sides laminae out of total 36) when assuming a tolerance of 1 mm on each side. Cross-sectional measurement results showed that the mean maximal thickness of upper, middle, and lower thirds was 5.0 mm, 7.5 mm, and 7.3 mm, respectively, and mean surface area for each part was 21.2 mm², 46.8 mm², and 34.7 mm², respectively. Fourteen (38.9%) sides of laminae would be feasible for 3.5 mm intralaminar screw insertion when upper thirds of C7 spino-laminar junction is the screw entry point. In case of middle and lower thirds of C7 spino-laminar junction, 32 (88.9%) and 28 (77.8%) sides of laminae were feasible for 3.5 mm screw insertion, respectively.

Conclusion

The vertical cross-sectioned area of middle thirds at C7 spinolaminar junction was the largest area and 3.5 mm screw can be accommodated with 77.8% of feasibility when lower thirds were the screw entry point. Thus, selection of middle and lower thirds for each side of screw entry point in spino-laminar junction would be the safest way to place bilateral crossing laminar screw within the entire lamina. This anatomic study result will help surgeons to place the screw safely and accurately.

Cervical pedicle screw insertion using the technique with direct exposure of the pedicle by laminoforaminotomy

Objective

To present the accuracy and safety of cervical pedicle screw insertion using the technique with direct exposure of the pedicle by laminoforaminotomy.

Methods

We retrospectively reviewed 12 consecutive patients. A total of 104 subaxial cervical pedicle screws in 12 patients had been inserted. We also assessed the clinical and radiological outcomes and analyzed the direction and grade of pedicle perforation (grade 0: no perforation, 1: <25%, 2: 20% to 50%, 3: >50% of screw diameter) on the postoperative vascular-enhanced computed tomography scans. Grade 2 and 3 were considered as incorrect position.

Results

The correct position was found in 95 screws (91.3%); grade 0-75 screws, grade 1-20 screws and the incorrect position in 9 screws (8.7%); grade 2-6 screws, grade 3-3 screws. There was no neurovascular complication related with cervical pedicle screw insertion.

Conclusion

This technique (technique with direct exposure of the pedicle by laminoforaminotomy) could be considered relatively safe and easy method to insert cervical pedicle screw.