Physicochemical Properties of Various 2-Hydroxyethylammonium Sulfonate -Based Protic Ionic Liquids and Their Potential Application in Hydrodeoxygenation

Implications for new particle formation in air of the use of monoethanolamine in carbon capture and storage

Alkanolamines are currently being deployed in carbon capture and storage (CCS) technology worldwide, and atmospheric emissions have been found to coincide with locations exhibiting elevated concentrations of methanesulfonic acid (MSA). It is thus critical to understand the fate and potential atmospheric reactions of these chemicals. This study reports the characterization of sub-10 nm nanoparticles produced through the acid-base reaction between gas phase monoethanolamine (MEA) and MSA, a product of organosulfur compound oxidation in air, using a flow reactor under dry and humid (up to ∼60% RH) conditions. Number size distribution measurements show that MEA is even more efficient than methylamine in forming nanoparticles on reaction with MSA. This is attributed to the fact that the MEA structure contains both an -NH2 and an -OH group that facilitate hydrogen bonding within the clusters, in addition to the electrostatic interactions. Due to this already strong H-bond network, water has a relatively small influence on new particle formation (NPF) and growth in this system, in contrast to MSA reactions with alkylamines. Acid/base molar ratios of unity for 4-12 nm particles were measured using thermal desorption chemical ionization mass spectrometry. The data indicate that reaction of MEA with MSA may dominate NPF under some atmospheric conditions. Thus, the unique characteristics of alkanolamines in NPF must be taken into account for accurate predictions of impacts of CCS on visibility, health and climate.

Experimental Investigation on Thermophysical Properties of Ammonium-Based Protic Ionic Liquids and Their Potential Ability towards CO2 Capture

Ionic liquids, which are extensively known as low-melting-point salts, have received significant attention as the promising solvent for CO₂ capture. This work presents the synthesis, thermophysical properties and the CO₂ absorption of a series of ammonium cations coupled with carboxylate anions producing ammonium-based protic ionic liquids (PILs), namely 2-ethylhexylammonium pentanoate ([EHA][C5]), 2-ethylhexylammonium hexanoate ([EHA][C6]), 2-ethylhexylammonium heptanoate ([EHA][C7]), bis-(2-ethylhexyl)ammonium pentanoate ([BEHA][C5]), bis-(2-ethylhexyl)ammonium hexanoate ([BEHA][C6]) and bis-(2-ethylhexyl)ammonium heptanoate ([BEHA][C7]). The chemical structures of the PILs were confirmed by using Nuclear Magnetic Resonance (NMR) spectroscopy while the density (ρ) and the dynamic viscosity (η) of the PILs were determined and analyzed in a range from 293.15K up to 363.15K. The refractive index (n_D) was also measured at T = (293.15 to 333.15) K. Thermal analyses conducted via a thermogravimetric analyzer (TGA) and differential scanning calorimeter (DSC) indicated that all PILs have the thermal decomposition temperature, T_d of greater than 416K and the presence of glass transition, T_g was detected in each PIL. The CO₂ absorption of the PILs was studied up to 29 bar at 298.15 K and the experimental results showed that [BEHA][C7] had the highest CO₂ absorption with 0.78 mol at 29 bar. The CO₂ absorption values increase in the order of [C5] < [C6] < [C7] anion regardless of the nature of the cation.

A review on tribological performance of ionic liquids as additives to bio lubricants

All the moving components in an internal combustion engine require a lubricant that allows smooth sliding and/or rolling of interacting surfaces. Lubricant not only minimizes the friction and wear but also dissipates the heat generated due to friction and removes debris from the area of contact. Environmental concerns, decreasing mineral oil reserves and difficult disposal of nonbiodegradable conventional lubricants have urged the researchers to shift towards environmental-friendly lubricants. Number of tribological studies carried out in the past have proved that ionic liquid-based bio-lubricants are sustainable and biodegradable alternative to mineral oils. This paper presents a brief review of properties of ionic liquids and their ability to reduce friction and wear between the interacting surfaces. Tribological performance and compatibility of ionic liquids with various base-oils have been compared under boundary lubrication. The results reveal that phosphonium-based ionic liquids namely tetra-decyl tri-hexyl phosphonium bis(2,4,4-trimethylpentyl) phosphinate (P66614)i(C8)2PO2 and tri-hexyl tetra-decyl phosphonium bis(2-ethylhexyl) phosphate (P-DEHP) are more suitable for tribological applications. Since, ionic liquids can be tailored according to the application and millions of combinations are possible therefore, there is a need to summarize the published data in a more systematic and logical way.

Thermophysical Properties of Newly Synthesized Ammonium-Based Protic Ionic Liquids: Effect of Temperature, Anion and Alkyl Chain Length

Ionic liquids which are often classified as low melting point salts have received significant attention from research groups and industries to be used in a wide range of applications. Many of these applications require thorough knowledge on the thermophysical properties of the ionic liquids before utilizing their full potentials in various fields. In this work, a series of alkylammonium cation and carboxylate anion-based room temperature protic ionic liquids (PILs) were synthesized by varying length of alkyl chain of the cation from diethyl to dibutyl combined with pentanoate, hexanoate and heptanoate anions. These ammonium-based PILs named as diethylammonium pentanoate [DEA][C5], diethylammonium hexanoate [DEA][C6], diethylammonium heptanoate [DEA][C7], dibutylammonium pentanoate [DBA][C5], dibutylammonium hexanoate [DBA][C6] and dibutylammonium heptanoate [DBA][C7] were characterized using Nuclear Magnetic Resonance (NMR) spectroscopy. The thermophysical properties of the PILs namely density, dynamic viscosity and refractive index were measured and analyzed. Density, ρ and dynamic viscosity, η were determined at T = (293.15 to 363.15) K and refractive index, nD was measured at T = (293.15 to 333.15) K. The fitting parameters are proposed for the empirical correlations of density, dynamic viscosity and refractive index. The values of thermal expansion coefficient, αp, molecular volume, Vm, standard entropy, S° and lattice potential energy, Upot also have been calculated by using the specified equations. The thermal decomposition temperature, Td was also determined using a thermogravimetric analyzer (TGA) while the differential scanning calorimetry (DSC) technique provided the glass transition, Tg, melting point, Tm and crystallization, Tc temperatures of the PILs. The experimental results revealed that the dependency of the experimental values namely the ρ, η, nD, and Td on the alkyl chain of the anion, size of the cations and the temperature of measurement.