Hollow WO3/SnO2 Hetero-Nanofibers: Controlled Synthesis and High Efficiency of Acetone Vapor Detection

Enhanced Performance of WO3/SnO2 Nanocomposite Electrodes with Redox-Active Electrolytes for Supercapacitors

For effective supercapacitors, we developed a process involving chemical bath deposition, followed by electrochemical deposition and calcination, to produce WO₃/SnO₂ nanocomposite electrodes. In aqueous solutions, the hexagonal WO₃ microspheres were first chemically deposited on a carbon cloth, and then tin oxides were uniformly electrodeposited. The synthesized WO₃/SnO₂ nanocomposite was characterized by XRD, XPS, SEM, and EDX techniques. Electrochemical properties of the WO₃/SnO₂ nanocomposite were analyzed by cyclic voltammetry, galvanostatic charge-discharge tests, and electrochemical impedance spectroscopy in an aqueous solution of Na₂SO₄ with/without the redox-active electrolyte K₃Fe(CN)₆. K₃Fe(CN)₆ exhibited a synergetic effect on the electrochemical performance of the WO₃/SnO₂ nanocomposite electrode, with a specific capacitance of 640 F/g at a scan rate of 5 mV/s, while that without K₃Fe(CN)₆ was 530 F/g. The WO₃/SnO₂ nanocomposite catalyzed the redox reactions of [Fe(CN)₆]³/[Fe(CN)₆]^4- ions, and the [Fe(CN)₆]^3-/[Fe(CN)₆]^4- ions also promoted redox reactions of the WO₃/SnO₂ nanocomposite. A symmetrical configuration of the nanocomposite electrodes provided good cycling stability (coulombic efficiency of 99.6% over 2000 cycles) and satisfied both energy density (60 Whkg^-1) and power density (540 Wkg^-1) requirements. Thus, the WO₃/SnO₂ nanocomposite prepared by this simple process is a promising component for a hybrid pseudocapacitor system with a redox-flow battery mechanism.

Low-Voltage-Driven SnO2-Based H2S Microsensor with Optimized Micro-Heater for Portable Gas Sensor Applications

To realize portable gas sensor applications, it is necessary to develop hydrogen sulfide (H2S) microsensors capable of operating at lower voltages with high response, good selectivity and stability, and fast response and recovery times. A gas sensor with a high operating voltage (>5 V) is not suitable for portable applications because it demands additional circuitry, such as a charge pump circuit (supply voltage of common circuits is approximately 1.8−5 V). Among H2S microsensor components, that is, the substrate, sensing area, electrode, and micro-heater, the proper design of the micro-heater is particularly important, owing to the role of thermal energy in ensuring the efficient detection of H2S. This study proposes and develops tin (IV)-oxide (SnO2)-based H2S microsensors with different geometrically designed embedded micro-heaters. The proposed micro-heaters affect the operating temperature of the H2S sensors, and the micro-heater with a rectangular mesh pattern exhibits superior heating performance at a relatively low operating voltage (3−4 V) compared to those with line (5−7 V) and rectangular patterns (3−5 V). Moreover, utilizing a micro-heater with a rectangular mesh pattern, the fabricated SnO2-based H2S microsensor was driven at a low operating voltage and offered good detection capability at a low H2S concentration (0−10 ppm), with a quick response (<51 s) and recovery time (<101 s).

A highly stable and sensitive ethanol sensor based on Ru-decorated 1D WO3 nanowires

Decorating materials with noble metal catalysts is an effective method for optimizing the sensing performance of sensors based on tungsten trioxide (WO₃) nanowires. Ruthenium (Ru) exhibits excellent catalytic activity for oxygen adsorption/desorption and chemical reactions between gases and adsorbed oxygen. Herein, small Ru nanoparticles were uniformly distributed on the surface of one-dimensional WO₃ nanowires. The nanowires were prepared by the electrospinning method through an ultraviolet (UV) irradiation process, and decoration with Ru did not change their morphology. A sensor based on 4% Ru nanowires (NWs) shows the highest response (∼120) to 100 ppm ethanol, which was increased around 47 times, and the lowest ethanol detection limit (221 ppb) at a lower temperature (200 °C) displays outstanding repeatability and stability even after 45 days or in higher-humidity conditions. Moreover, it also has faster response–recovery features. The improvement in the sensing performance was attributed to the stable morphology of the nanowires, the sensitization effect of Ru, the catalytic effect of RuO₂ and the optimal atomic utilization efficiency. This work offers an effective and promising strategy for promoting the ethanol sensing performance of WO₃.

Decorating Ru does not effect the morphology of NWs, increased the oxygen vacancies, adsorbed oxygen. This strategy results in a better sensing performance (∼120 to 100 ppm ethanol was increased around 47 times at 200 °C) and humidity resistance.

Rational Design of Semiconductor-Based Chemiresistors and their Libraries for Next-Generation Artificial Olfaction

Artificial olfaction based on gas sensor arrays aims to substitute for, support, and surpass human olfaction. Like mammalian olfaction, a larger number of sensors and more signal processing are crucial for strengthening artificial olfaction. Due to rapid progress in computing capabilities and machine-learning algorithms, on-demand high-performance artificial olfaction that can eclipse human olfaction becomes inevitable once diverse and versatile gas sensing materials are provided. Here, rational strategies to design a myriad of different semiconductor-based chemiresistors and to grow gas sensing libraries enough to identify a wide range of odors and gases are reviewed, discussed, and suggested. Key approaches include the use of p-type oxide semiconductors, multinary perovskite and spinel oxides, carbon-based materials, metal chalcogenides, their heterostructures, as well as heterocomposites as distinctive sensing materials, the utilization of bilayer sensor design, the design of robust sensing materials, and the high-throughput screening of sensing materials. In addition, the state-of-the-art and key issues in the implementation of electronic noses are discussed. Finally, a perspective on chemiresistive sensing materials for next-generation artificial olfaction is provided.