Copper/Nickel-Decorated Olive Pit Biochar: One Pot Solid State Synthesis for Environmental Remediation

A novel Ce-Ni@biochar nanocomposite with enhanced photocatalytic activity towards organic dyes degradation: impact of process variables and water matrices

The intent of this research work is to implement a biogenic, affordable, and highly effective Ce-Ni@biochar catalyst in order to study its photoactivity in the removal of crystal violet and malachite green oxalate. The catalyst was synthesized using liquid phase reduction method where cerium and nickel nanoparticles are embedded on the rice husk biochar for photocatalytic degradation of organic dyes in the presence of sunshine. Various characterization techniques were conducted on fabricated catalyst for adequate evaluation of the chemical composition as well as morphological and topographical properties of the formed compound. The nanoparticles embedded on biochar persuade increased charge separation that resulted in a substantial decrease in electron-hole recombination rate. The synergistic actions of the catalyst resulted in a high level of photocatalytic activity. The fabricated nanocatalyst showed excellent photoactivity that caused 96 and 99% degradation of crystal violet and malachite green oxalate, a growing industrial pollutant, within 35 and 25 min, respectively. A persuasive mechanism and kinetics are well presented. A series of investigations were done on other factors, such as contact duration, catalyst dosage, starting concentration, interfering ions, and pH, to know its degradation pursuance. The impacts of different water matrices were also investigated. The removal effectiveness of the synthesized catalyst persisted after five consecutive cycles. Marking the burgeoning industrial effluents as a result of rapid industrialization and also focusing on easy availability and low-cost source as well as high efficiency, reusability of the catalyst imparts its novelty and need of this research work.

Citric-Acid-Assisted Preparation of Biochar Loaded with Copper/Nickel Bimetallic Nanoparticles for Dye Degradation

Immobilization of nanocatalysts on biochar is receiving unprecedented interest among material and catalysis scientists due to its simplicity, versatility, and high efficiency. Herein, we propose a new direct approach to obtain bimetallic copper/nickel nanoparticles loaded on olive stone biochar. The bimetallic-coated biochar and the reference materials, namely bare biochar, copper rich-loaded biochar, and nickel-loaded biochar, were prepared by pyrolysis from olive pit powder particles impregnated first with citric acid (CA) and then with copper and nickel nitrates at 400 °C under nitrogen flow. We employed citric acid in the process in order to examine its effect on the structural and textural properties of biochar supporting the metallic nanoparticles. Surprisingly, citric acid induced the formation of agglomerated or even raspberry-shaped bimetallic copper/nickel nanoparticles. Large 450–500 nm agglomerates of ~80 nm bimetallic CuNi NPs were noted for B-CA@CuNi. Interestingly, for biochar material prepared with initial Cu/Ni = 10 molar ratio (B-CA@CuNi10/1), the bimetallic NPs formed unusual nanoraspberries (174 ± 8 nm in size), which were agglomerates of individual 10–20 nm CuNi10/1 nanoparticles. The B-CA@CuNi and reference materials were characterized by Raman spectroscopy, scanning electron microscopy (SEM)/energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), and magnetometry. The B-CA@CuNi and B-CA@Ni materials could be efficiently attracted with a magnet but not B-CA@CuNi10/1 due to the low nickel loading. B-CA@CuNi was tested as a catalyst for the degradation of methyl orange (MO). Discoloration was noted within 10 min, much faster than a similar material prepared in the absence of CA. B-CA@CuNi could be recycled at least 3 times while still exhibiting the same fast catalytic discoloration performance. This paper stresses the important role of citric acid in shaping bimetallic nanoparticles loaded in situ on biochar during the slow pyrolysis process and in enabling faster catalytic discoloration of organic dye solution.

Electrical conductivity and thermal stability of surface-modified multiwalled carbon nanotubes/polysulfone/poly(p-phenylenediamine) composites

Multiwalled carbon nanotubes (MWCNTs) were functionalized with acid then coated with poly(p-phenylenediamine) (PpPD). Various concentrations of modified multiwalled carbon nanotubes (MWCNTs@PpPD) were introduced to a polysulfone (PSU) and poly(p-phenylenediamine) (PpPD) blend providing nanocomposites in form of sheets. Chemical oxidative polymerization was used to polymerize p-phenylenediamine. PpPD is then applied as a compatibilizer in such heterogeneous system to facilitate a successful percolation for MWCNTs in the polymeric matrix as an enhanced conductive filler. The morphological investigations showed homogeneous distribution for MWCNTs in the polymeric matrix. The prepared composites were investigated demonstrating favorable thermal and electrical properties. Thermogravimetric analysis (TGA) emphasized that MWCNTs@PpPD contributed in enhancing the thermal stability of the prepared sheets. The electrical conductivity of PSU/PpPD/MWCNTs@PpPD nanocomposites boosted upon raising the magnitude of loaded MWCNTs. The existence of MWCNTs@PpPD in the polymeric matrix extended the interfacial polarization effects with elevating the conductance. The loaded composite with (7.5 wt%) MWCNTs@PpPD showed the optimum electrical conductivity values. It was then treated with HCl to protonate the amine groups in PpPD showing higher conductivity value than its corresponding untreated one. PpPD and MWCNTs contributed synergistically in modifying the insulation feature of PSU to a favorable electrical conductivity one.