Polymer-Based Microring Resonator with the Multimode Interference Coupler Operating at Very-Near-Infrared Wavelengths

Highly sensitive ultrasound detection using nanofabricated polymer micro-ring resonators

Photoacoustic (PA) imaging enables noninvasive volumetric imaging of biological tissues by capturing the endogenous optical absorption contrast. Conventional ultrasound detectors using piezoelectric materials have been widely used for transducing ultrasound signals into the electrical signals for PA imaging reconstruction. However, their inherent limitations in detection bandwidth and sensitivity per unit area have unfortunately constrained the performance of PA imaging. Optical based ultrasound detection methods emerge to offer very promising solutions. In particular, polymer micro-ring resonators (MRRs) in the form of integrated photonic circuits (IPC) enable significant reduction for the sensing area to 80 μm in diameter, while maintaining highly sensitive ultrasound detection with noise equivalent pressure (NEP) of 0.49 Pa and a broad detection frequency range up to 250 MHz. The continued engineering innovation has further transformed MRRs to be transparent to the light and thus, opens up a wide range of applications, including multi-modality optical microscope with isometric resolution, PA endoscope, photoacoustic computed tomography (PACT), and more. This review article summarizes and discusses the evolution of polymer MRR design and the associated nanofabrication process for improving the performance of ultrasound detection. The resulting novel imaging applications will also be reviewed and discussed.

High-Q-Factor Silica-Based Racetrack Microring Resonators

In this paper, ultrahigh-Q factor racetrack microring resonators (MRRs) are demonstrated based on silica planar lightwave circuits (PLCs) platform. A loaded ultrahigh-Q factor Qload of 1.83 × 106 is obtained. The MRRs are packaged with fiber-to-fiber loss of ~5 dB. A notch depth of 3 dB and ~137 pm FSR are observed. These MRRs show great potential in optical communications as filters. Moreover, the devices are suitable used in monolithic integration and hybrid integration with other devices, especially in external cavity lasers (ECLs) to realize ultranarrow linewidths.

Enhanced Sensitivity of Microring Resonator-Based Sensors Using the Finite Difference Time Domain Method to Detect Glucose Levels for Diabetes Monitoring

The properties of light and its interaction with biological analytes have made it possible to design sophisticated and reliable optical-based biomedical sensors. In this paper, we report the simulation, design, and fabrication of microring resonator (MRR)-based sensors for the detection of diabetic glucose levels. Electron Beam Lithography (EBL) with 1:1 hydrogen silsesquioxane (HSQ) negative tone resist were used to fabricate MRR on a Silicon-on-Insulator (SOI) platform. Scanning Electron Microscopy (SEM) was then used to characterize the morphology of the MRR device. The full-width at half-maximum (FWHM) and quality factors of MRR were obtained by using a tunable laser source (TLS) and optical spectrum analyzer (OSA). In this paper, the three-dimensional Finite Difference Time Domain (3D FDTD) approach has been used to simulate the proposed design. The simulation results show an accurate approximation with the experimental results. Next, the sensitivity of MRR-based sensors to detect glucose levels is obtained. The sensitivity value for glucose level detection in the range 0% to 18% is 69.44 nm/RIU. This proved that our MRR design has a great potential as a sensor to detect diabetic glucose levels.

Metal-Printing Defined Thermo-Optic Tunable Sampled Apodized Waveguide Grating Wavelength Filter Based on Low Loss Fluorinated Polymer Material

In this work, thermo-optic (TO) lateral shift apodized sampled waveguide grating for 1550 nm wavelength is designed and fabricated by the metal-printing technique based on fluorinated epoxy-terminated polycarbonates (FBPA-PC EP) and fluorinated epoxy resin (FSU-8) materials. The optical characteristics and thermal stability of the FBPA-PC EP and FSU-8 materials are analyzed. To realize periodic wide-spectrum filtering and suppress the side-lobes of grating, a lateral shift apodized sampled waveguide grating is proposed. The 3 dB bandwidth and wavelength spacing can reach 4.8 nm and 9.7 nm. The side-lobe suppression ratio of proposed device can reach 22.6 dB, which is much better than traditional Bragg grating (6.1 dB). Driving electrical powers of 42.4 mW and 87.2 mW can produce blueshifts of 1.8 nm and 3.5 nm in the measured reflection spectrum, respectively. This device realizes the aim of multiple functions, including periodic filtering, wide-spectrum filtering, and high side-lobe suppression. The device is applicable of realizing signal processing and wavelength division multiplexing (WDM )systems.