Surface Alterations Induced on Endodontic Instruments by Sterilization Processes, Analyzed with Atomic Force Microscopy: A Systematic Review

Influence of 17% EDTA and Sapindus mukorossi on the Surface Property of Protaper Gold Rotary Endodontic Instruments

The aim of the study was to evaluate the influence of 17% ethylenediaminetetraacetic acid (EDTA) and ethanolic extract of Sapindus mukorossi (S. mukorossi) in combination with canal shaping on surface properties of ProTaper Gold rotary endodontic file. Sixteen F1 ProTaper Gold rotary files underwent the standard protocol for root canal treatment using two irrigants (S. mukorossi and 17% EDTA) in single-rooted decoronated teeth. Eight unused files were used as a control. All files were examined under an atomic force microscope (AFM) to evaluate surface roughness (Ra) and root mean square (RMS). Data were analyzed using the t-test. RMS and Ra values of the control file were 1.37 and 0.607, respectively. The mean RMS (3.70 ± 1.41) and mean Ra (2.89 ± 1.41) in EDTA group were significantly higher than the control file (p < 0.05). The mean RMS in the S. mukorossi group (1.77 ± 0.66) did not show any significant difference with the control (p > 0.05). The Ra of S. mukorossi group (1.09 ± 0.05) was significantly higher than the control file (p < 0.05). Moreover, the mean RMS and Ra were found to be significantly higher in the EDTA group compared to the S. mukorossi group (p < 0.05). The mean Ra and RMS values of the ProTaper Gold files used to prepare canals using 17% EDTA and S. mukorossi irrigation were significantly higher than the control files. The EDTA-treated ProTaper Gold rotary files demonstrated higher surface Ra and RMS than the S. mukorossi files.

Experimental Study of the Effects of Torsional Loading on Three Types of Nickel-Titanium Endodontic Instruments

In modern endodontics, nickel-titanium (NiTi) rotary instruments are used on a large scale for root canal shaping. Nevertheless, the separation of an instrument is a serious concern during shaping. The aim of this study is to determine and compare the torsional fracture characteristics of three types of NiTi endodontic instruments, each with different cross-section designs and movements performed during root canal shaping: Endostar E3 (Endostar, Poldent Co. Ltd., Warsaw, Poland); Reciproc R25 (VDW, Munich, Germany); and Protaper Next X2 (Dentsply Maillefer, Ballaigues, Switzerland). Fifteen instruments are used in this study, divided in three groups (n = 5): Group Endostar, Group Reciproc and Group Protaper. For testing, each instrument is used to shape five simulated root canals, following which its torsional stress to failure is measured. The fracture lengths of all three groups are roughly between 2 and 3 mm from the tip. Higher values of the moment of torsion in fracture, and smaller values of the maximum twisting angle are observed for Group Endostar, as well as closer to circular cross-sections. However, the values of the shear tension are similar for all three groups, because the disadvantage given by the fracture section shape for Groups Reciproc and Protaper is compensated either by size or by intrinsic properties of the instrument material. For the shear tension the Endostar values are insignificantly increased (Kruskal–Wallis test, p = 0.207), and in the case of the maximum twist angle the Protaper values are insignificantly increased (Kruskal–Wallis test, p = 0.287). Because of the instruments shape and conicity, the analysis had to be carried out separately with regard to the length of the fractured tip. Rules-of-thumb are extracted from the study for current practice: if a blockage of the first 2 to 3 mm part of the tip can be anticipated (by the excessive curving of the instrument), the handpiece must be adjusted to torque values that do not exceed 1.5 to 2.5 N · cm for Endostar and 1 to 2 N · cm for Reciproc and Protaper instruments.

Effects of repeated sterilization cycles on the surface alterations of ProTaper Next, TF Adaptive, HyFlex CM, and 2Shape instruments

Background. This study aimed to evaluate the effects of repeated sterilization cycles on the surface alterations of various nickel-titanium instruments, including ProTaper Next (PTN), TF Adaptive (TFA), HyFlex CM (HCM), and 2Shape (2S). Methods. Twenty-four new NiTi files of four different alloys were selected. The instruments in each group were divided into two equal groups, as follows: control and sterilization. The first group was chosen as the control without applying any sterilization procedure, while in group 2, five cycles of sterilization procedures were applied. The surface topographies were evaluated using scanning electron microscope (SEM) and atomic force microscope (AFM). The root mean square (RMS) and maximum height (MH) values and three-dimensional images were recorded. The data were analyzed with the Shapiro-Wilk test, one-way ANOVA, and post hoc Tukey tests. The statistical significance level was set at P ≤ 0.05. Results. Before the experiment, HCM demonstrated the highest RMS value, and 2S showed the lowest. After the procedures, the RMS and MH values deteriorated on the surface of PTX, TFA, and 2S (P < 0.001). The HCM was not affected by sterilization processes (P > 0.05). Conclusion. The initial irregularity on the surface did not affect the rate of alteration. The HCM files demonstrated superior surface properties after several cycles of sterilization. The PTN, TFA, and 2S presented similar surface responses after five cycles of autoclave sterilization.

The Effects of Sterilization Procedures on the Cutting Efficiency of Endodontic Instruments: A Systematic Review and Network Meta-Analysis

Sterilization processes guarantee the sterility of dental instruments but can negatively affect instrument features by altering their physical and mechanical properties. The endodontic instrumentation can undergo a series of alterations, ranging from corrosion to variation in the cutting angle and then changes in the torsional properties and torsional fatigue resistance. This systematic literature review and meta-analysis aims to investigate alterations to the cutting efficiency of endodontic instruments that are induced by procedures for their disinfection and sterilization. Methodologies adopted for this investigation follow the PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analysis) guidelines. The following were used as search terms on PubMed and Scopus: "endodontic sterilization", "endodontic autoclave", "cyclic fatigue", "torsional", "cutting efficiency", "sterilization", "surface characteristics", and "corrosion". At the end of the selection process, 36 articles were identified, and seven of them are included in this systematic review. The results of a meta-analysis conducted for the use of 10 autoclaving cycles shows a standardized mean difference (SMD) of 0.80 with a p-value equal to 0.04 with respect to effect on cutting efficiency. The network meta-analysis, through direct and indirect comparison between the different autoclave cycles (0, 1, 5, 10, and 15 cycles), revealed that treatment involving 15 autoclave cycles produced the most robust results in terms of having the greatest effects in terms of altered cutting efficiency with a probability of 57.7% and a SUCRA (surface under the cumulative ranking) of 80%. The alterations in the effects on cutting efficiency appear to be triggered after five cycles of sterilization by heat (autoclave). In conclusion, the meta-analysis of the data indicates that the autoclave sterilization protocol must not be repeated more than five times to preserve cutting efficiency. Within the limitations of this review, we can therefore establish that sterilization by autoclaving alone results in steel and NiTi instruments becoming less efficient in cutting after five cycles, as measured by a reduction in cutting efficiency.

Oral Health and Related Factors Associated with General Health and Quality of Life

Oral well-being is an integral part of individual general health. The mouth and teeth are, in fact, part of our body, increasingly characterizing personal identity. Oral diseases are a public health problem that has a growing prevalence. Oral pathologies can occur in childhood, and as they have a chronic and progressive course, if not properly treated, they can affect the relational, psychological, and social skills of an individual. The population most affected are those with a low socio-economic level, so much so that the presence of diseases of the oral cavity is considered a marker of social disadvantage. In this regard, much effort is needed from scientists, and their applied sciences, in order to give the knowledge required for public health personal to take note of the seriousness of the situation and to start changing the way we deal with the problem.