3D-Printed Coronary Plaques to Simulate High Calcification in the Coronary Arteries for Investigation of Blooming Artifacts

In-vitro Detection of Intramammary-like Macrocalcifications Using Susceptibility-weighted MR Imaging Techniques at 1.5T

PURPOSE

The aim of our study was to investigate the technical accuracy of susceptibility-weighted imaging (SWI) and quantitative susceptibility mapping (QSM) created to detect intramammary-like calcifications depending on different TEs, volume, and type of calcification samples at 1.5T.

METHODS

Jello-embedded particles of blackboard chalk and ostrich eggshell ranging in size from 4 to 25 mm2 were used to simulate intramammary calcifications after testing different base substances and calcifications for their suitability to be used in breast phantoms. Breast phantoms were systematically examined using CT and an optimized 3D multi-echo gradient echo pulse sequence with following parameters: TR/TE, 22/1.88-15.52 ms in 1.24 ms increments; reconstructed voxel, 0.5 × 0.5 × 1.1 mm3; receiver bandwidth, 1120 Hz/Px; flip angle, 15°; integrated parallel imaging technique with a GeneRalized Autocalibrating Partial Parallel Acquisition (GRAPPA) factor of 2/24; and a total acquisition time of 3:00 min. A qualitative evaluation of the dependence of the visualization of calcification samples on volume and TE value was followed by a calculation of the SNR, the contrast-to-noise ratio (CNR) and the creation of SWI and QSM in the sense of a (semi)-quantitative analysis of the images.

RESULTS

Jello proved to be a suitable base substance for preparing breast phantoms for SW MRI. Blackboard chalk and ostrich eggshell proved to be suitable for mimicking intramammary-like calcifications. The decrease in the median SNR of the blackboard chalk samples was significantly higher than the corresponding value of the ostrich eggshell samples over the entire TE range (47.5 to 17.0 vs. 16.0 to 6.56, P < 0.0001). The increase in the median CNR of the blackboard chalk samples was significantly higher than the corresponding value of the ostrich eggshell samples over the entire TE range (2.46 to 35.0 vs. 20.2 to 36.8, P = 0.007). With increasing TE value, the signal void volume of the calcification particle increases in the magnitude images as well as in SWI and QSM. Due to the blooming effect, the median gradients of the TE-based changes in signal void volumes were higher in SWI than in magnitude images and in QSM, regardless of the type of calcification particle examined. The maximum magnetic susceptibility of ostrich eggshell samples varied in a TE range of 1.88 to 15.52 ms from -7.2 to -2.51 ppm and that of blackboard chalk from -2.0 to -1.7 ppm. Compared to the manually measured volumes of the calcification particles, both MR-based measurements and CT examinations overestimated the actual sample size. The (non)-significant overestimation in the MRI-data is dependent on the set TE. The CT-based hyperdense volumes were overestimated compared to the corresponding manually measured sample volumes in a range of 109.8%-315.2% for ostrich eggshell samples (P = 0.016) and in a range of 39.9%-156.4% for blackboard chalk samples (P = 0.69).

CONCLUSION

Our systematic in-vitro investigation of magnitude images, SWI, and QSM revealed that various set TE values, different volumes, and compositions of calcifications have a significant impact on visualizing intramammary(-like) calcifications.

Cardiovascular computed tomography in cardiovascular disease: An overview of its applications from diagnosis to prediction

Cardiovascular computed tomography angiography (CTA) is a widely used imaging modality in the diagnosis of cardiovascular disease. Advancements in CT imaging technology have further advanced its applications from high diagnostic value to minimising radiation exposure to patients. In addition to the standard application of assessing vascular lumen changes, CTA-derived applications including 3D printed personalised models, 3D visualisations such as virtual endoscopy, virtual reality, augmented reality and mixed reality, as well as CT-derived hemodynamic flow analysis and fractional flow reserve (FFRCT) greatly enhance the diagnostic performance of CTA in cardiovascular disease. The widespread application of artificial intelligence in medicine also significantly contributes to the clinical value of CTA in cardiovascular disease. Clinical value of CTA has extended from the initial diagnosis to identification of vulnerable lesions, and prediction of disease extent, hence improving patient care and management. In this review article, as an active researcher in cardiovascular imaging for more than 20 years, I will provide an overview of cardiovascular CTA in cardiovascular disease. It is expected that this review will provide readers with an update of CTA applications, from the initial lumen assessment to recent developments utilising latest novel imaging and visualisation technologies. It will serve as a useful resource for researchers and clinicians to judiciously use the cardiovascular CT in clinical practice.

Biomimicking Atherosclerotic Vessels: A Relevant and (Yet) Sub-Explored Topic

Atherosclerosis represents the etiologic source of several cardiovascular events, including myocardial infarction, cerebrovascular accidents, and peripheral artery disease, which remain the leading cause of mortality in the world. Numerous strategies are being delineated to revert the non-optimal projections of the World Health Organization, by both designing new diagnostic and therapeutic approaches or improving the interventional procedures performed by physicians. Deeply understanding the pathological process of atherosclerosis is, therefore, mandatory to accomplish improved results in these trials. Due to their availability, reproducibility, low expensiveness, and rapid production, biomimicking physical models are preferred over animal experimentation because they can overcome some limitations, mainly related to replicability and ethical issues. Their capability to represent any atherosclerotic stage and/or plaque type makes them valuable tools to investigate hemodynamical, pharmacodynamical, and biomechanical behaviors, as well as to optimize imaging systems and, thus, obtain meaningful prospects to improve the efficacy and effectiveness of treatment on a patient-specific basis. However, the broadness of possible applications in which these biomodels can be used is associated with a wide range of tissue-mimicking materials that are selected depending on the final purpose of the model and, consequently, prioritizing some materials' properties over others. This review aims to summarize the progress in fabricating biomimicking atherosclerotic models, mainly focusing on using materials according to the intended application.

Cardiovascular Computed Tomography in the Diagnosis of Cardiovascular Disease: Beyond Lumen Assessment

Cardiovascular CT is being widely used in the diagnosis of cardiovascular disease due to the rapid technological advancements in CT scanning techniques. These advancements include the development of multi-slice CT, from early generation to the latest models, which has the capability of acquiring images with high spatial and temporal resolution. The recent emergence of photon-counting CT has further enhanced CT performance in clinical applications, providing improved spatial and contrast resolution. CT-derived fractional flow reserve is superior to standard CT-based anatomical assessment for the detection of lesion-specific myocardial ischemia. CT-derived 3D-printed patient-specific models are also superior to standard CT, offering advantages in terms of educational value, surgical planning, and the simulation of cardiovascular disease treatment, as well as enhancing doctor-patient communication. Three-dimensional visualization tools including virtual reality, augmented reality, and mixed reality are further advancing the clinical value of cardiovascular CT in cardiovascular disease. With the widespread use of artificial intelligence, machine learning, and deep learning in cardiovascular disease, the diagnostic performance of cardiovascular CT has significantly improved, with promising results being presented in terms of both disease diagnosis and prediction. This review article provides an overview of the applications of cardiovascular CT, covering its performance from the perspective of its diagnostic value based on traditional lumen assessment to the identification of vulnerable lesions for the prediction of disease outcomes with the use of these advanced technologies. The limitations and future prospects of these technologies are also discussed.

Comparative Study of Plan Robustness for Breast Radiotherapy: Volumetric Modulated Arc Therapy Plans with Robust Optimization versus Manual Flash Approach

A previous study investigated robustness of manual flash (MF) and robust optimized (RO) volumetric modulated arc therapy plans for breast radiotherapy based on five patients in 2020 and indicated that the RO was more robust than the MF, although the MF is still current standard practice. The purpose of this study was to compare their plan robustness in terms of dose variation to clinical target volume (CTV) and organs at risk (OARs) based on a larger sample size. This was a retrospective study involving 34 female patients. Their plan robustness was evaluated based on measured volume/dose difference between nominal and worst scenarios (ΔV/ΔD) for each CTV and OARs parameter, with a smaller difference representing greater robustness. Paired sample t-test was used to compare their robustness values. All parameters (except CTV ΔD98%) of the RO approach had smaller ΔV/ΔD values than those of the MF. Also, the RO approach had statistically significantly smaller ΔV/ΔD values (p < 0.001-0.012) for all CTV parameters except the CTV ΔV95% and ΔD98% and heart ΔDmean. This study's results confirm that the RO approach was more robust than the MF in general. Although both techniques were able to generate clinically acceptable plans for breast radiotherapy, the RO could potentially improve workflow efficiency due to its simpler planning process.

Three-Dimensional Bioprinting in Cardiovascular Disease: Current Status and Future Directions

Three-dimensional (3D) printing plays an important role in cardiovascular disease through the use of personalised models that replicate the normal anatomy and its pathology with high accuracy and reliability. While 3D printed heart and vascular models have been shown to improve medical education, preoperative planning and simulation of cardiac procedures, as well as to enhance communication with patients, 3D bioprinting represents a potential advancement of 3D printing technology by allowing the printing of cellular or biological components, functional tissues and organs that can be used in a variety of applications in cardiovascular disease. Recent advances in bioprinting technology have shown the ability to support vascularisation of large-scale constructs with enhanced biocompatibility and structural stability, thus creating opportunities to replace damaged tissues or organs. In this review, we provide an overview of the use of 3D bioprinting in cardiovascular disease with a focus on technologies and applications in cardiac tissues, vascular constructs and grafts, heart valves and myocardium. Limitations and future research directions are highlighted.

Diagnostic Performance of Artificial Intelligence-Based Computer-Aided Detection and Diagnosis in Pediatric Radiology: A Systematic Review

Artificial intelligence (AI)-based computer-aided detection and diagnosis (CAD) is an important research area in radiology. However, only two narrative reviews about general uses of AI in pediatric radiology and AI-based CAD in pediatric chest imaging have been published yet. The purpose of this systematic review is to investigate the AI-based CAD applications in pediatric radiology, their diagnostic performances and methods for their performance evaluation. A literature search with the use of electronic databases was conducted on 11 January 2023. Twenty-three articles that met the selection criteria were included. This review shows that the AI-based CAD could be applied in pediatric brain, respiratory, musculoskeletal, urologic and cardiac imaging, and especially for pneumonia detection. Most of the studies (93.3%, 14/15; 77.8%, 14/18; 73.3%, 11/15; 80.0%, 8/10; 66.6%, 2/3; 84.2%, 16/19; 80.0%, 8/10) reported model performances of at least 0.83 (area under receiver operating characteristic curve), 0.84 (sensitivity), 0.80 (specificity), 0.89 (positive predictive value), 0.63 (negative predictive value), 0.87 (accuracy), and 0.82 (F1 score), respectively. However, a range of methodological weaknesses (especially a lack of model external validation) are found in the included studies. In the future, more AI-based CAD studies in pediatric radiology with robust methodology should be conducted for convincing clinical centers to adopt CAD and realizing its benefits in a wider context.

Patient-Specific 3D-Printed Low-Cost Models in Medical Education and Clinical Practice

3D printing has been increasingly used for medical applications with studies reporting its value, ranging from medical education to pre-surgical planning and simulation, assisting doctor-patient communication or communication with clinicians, and the development of optimal computed tomography (CT) imaging protocols. This article presents our experience of utilising a 3D-printing facility to print a range of patient-specific low-cost models for medical applications. These models include personalized models in cardiovascular disease (from congenital heart disease to aortic aneurysm, aortic dissection and coronary artery disease) and tumours (lung cancer, pancreatic cancer and biliary disease) based on CT data. Furthermore, we designed and developed novel 3D-printed models, including a 3D-printed breast model for the simulation of breast cancer magnetic resonance imaging (MRI), and calcified coronary plaques for the simulation of extensive calcifications in the coronary arteries. Most of these 3D-printed models were scanned with CT (except for the breast model which was scanned using MRI) for investigation of their educational and clinical value, with promising results achieved. The models were confirmed to be highly accurate in replicating both anatomy and pathology in different body regions with affordable costs. Our experience of producing low-cost and affordable 3D-printed models highlights the feasibility of utilizing 3D-printing technology in medical education and clinical practice.

Medical Fuzzy-Expert System for Assessment of the Degree of Anatomical Lesion of Coronary Arteries

BACKGROUND

Today, cardiovascular diseases cause 47% of all deaths among the European population, which is 4 million cases every year. In Ukraine, CAD accounts for 65% of the mortality rate from circulatory system diseases of the able-bodied population and is the main cause of disability. The aim of this study is to develop a medical expert system based on fuzzy sets for assessing the degree of coronary artery lesions in patients with coronary artery disease.

METHODS

The method of using fuzzy sets for the implementation of an information expert system for solving the problems of medical diagnostics, in particular, when assessing the degree of anatomical lesion of the coronary arteries in patients with various forms of coronary artery disease, has been developed.

RESULTS

The paper analyses the main areas of application of mathematical methods in medical diagnostics, and formulates the principles of diagnostics, based on fuzzy logic. The developed models and algorithms of medical diagnostics are based on the ideas and principles of artificial intelligence and knowledge engineering, the theory of experiment planning, the theory of fuzzy sets and linguistic variables. The expert system is tested on real data. Through research and comparison of the results of experts and the created medical expert system, the reliability of supporting the correct decision making of the medical expert system based on fuzzy sets for assessing the degree of anatomical lesion of the coronary arteries in patients with various forms of coronary artery disease with the assessment of experts was 95%, which shows the high efficiency of decision making.

CONCLUSIONS

The practical value of the work lies in the possibility of using the automated expert system for the solution of the problems of medical diagnosis based on fuzzy logic for assessing the degree of anatomical lesion of the coronary arteries in patients with various forms of coronary artery disease. The proposed concept must be further validated for inter-rater consistency and reliability. Thus, it is promising to create expert medical systems based on fuzzy sets for assessing the degree of disease pathology.

3D Printed Models in Cardiovascular Disease: An Exciting Future to Deliver Personalized Medicine

3D printing has shown great promise in medical applications with increased reports in the literature. Patient-specific 3D printed heart and vascular models replicate normal anatomy and pathology with high accuracy and demonstrate superior advantages over the standard image visualizations for improving understanding of complex cardiovascular structures, providing guidance for surgical planning and simulation of interventional procedures, as well as enhancing doctor-to-patient communication. 3D printed models can also be used to optimize CT scanning protocols for radiation dose reduction. This review article provides an overview of the current status of using 3D printing technology in cardiovascular disease. Limitations and barriers to applying 3D printing in clinical practice are emphasized while future directions are highlighted.

Artificial Intelligence for Radiation Dose Optimization in Pediatric Radiology: A Systematic Review

Radiation dose optimization is particularly important in pediatric radiology, as children are more susceptible to potential harmful effects of ionizing radiation. However, only one narrative review about artificial intelligence (AI) for dose optimization in pediatric computed tomography (CT) has been published yet. The purpose of this systematic review is to answer the question “What are the AI techniques and architectures introduced in pediatric radiology for dose optimization, their specific application areas, and performances?” Literature search with use of electronic databases was conducted on 3 June 2022. Sixteen articles that met selection criteria were included. The included studies showed deep convolutional neural network (CNN) was the most common AI technique and architecture used for dose optimization in pediatric radiology. All but three included studies evaluated AI performance in dose optimization of abdomen, chest, head, neck, and pelvis CT; CT angiography; and dual-energy CT through deep learning image reconstruction. Most studies demonstrated that AI could reduce radiation dose by 36–70% without losing diagnostic information. Despite the dominance of commercially available AI models based on deep CNN with promising outcomes, homegrown models could provide comparable performances. Future exploration of AI value for dose optimization in pediatric radiology is necessary due to small sample sizes and narrow scopes (only three modalities, CT, positron emission tomography/magnetic resonance imaging and mobile radiography, and not all examination types covered) of existing studies.