Bifunctional CuO-Ag/KB Catalyst for the Electrochemical Reduction of CO2 in an Alkaline Solid-State Electrolysis Cell

The conversion of carbon dioxide into value-added products is progressively gaining momentum. Several strategies have been used to develop technologies that reduce the net emissions of CO2. The utilisation of CO2 could either contribute to carbon recycling. In this paper, the transformation of CO2 was investigated in a coelectrolysis cell constituted of a solid polymer electrolyte, a carbon-supported CuO-Ag composite cathode and NiFeOx anode. Noncritical raw materials were synthesised according to the oxalate method and investigated in an alkaline environment. Low-carbon alcohols were obtained with a specific selectivity for ethanol and methanol over the CuO-Ag/KB cathode. The reaction rates at 1.6 V and 1.8 V cell voltages have been determined in steady-state experiments using NaHCO3 supporting electrolyte recirculated at the anode.

Water Splitting with Enhanced Efficiency Using a Nickel-Based Co-Catalyst at a Cupric Oxide Photocathode

Homemade non-critical raw materials such as Ni or NiCu co-catalysts were added at the photocathode of a tandem cell, constituted by photoelectrodes made of earth-abundant materials, to generate green solar hydrogen from photoelectrochemical water splitting. Oxygen evolving at the Ti-and-P-doped hematite/TCO-based photoanode and hydrogen at the cupric oxide/GDL-based photocathode are separated by an anion exchange polymer electrolyte membrane placed between them. The effect of the aforementioned co-catalysts was studied in a complete PEC cell in the presence of the ionomer dispersion and the anionic membrane to evaluate their impact under practical conditions. Notably, different amounts of Ni or NiCu co-catalysts were used to improve the hydrogen evolution reaction (HER) kinetics and the overall solar-to-hydrogen (STH) efficiency of the photoelectrochemical cells. At −0.6 V, in the bias-assisted region, the photocurrent density reaches about 2 mA cm−2 for a cell with 12 µg cm−2 of Ni loading, followed by 1.75 mA cm−2 for the cell configuration based on 8 µg cm−2 of NiCu. For the best-performing cell, enthalpy efficiency at −0.4 V reaches a first maximum value of 2.03%. In contrast, the throughput efficiency, which is a ratio between the power output and the total power input (solar + electric) provided by an external source, calculated at −1.225 V, reaches a maximum of 10.75%. This value is approximately three times higher than the best results obtained in our previous studies without the use of co-catalysts at the photocathode.

Anionic Exchange Membrane for Photo-Electrolysis Application

Tandem photo-electro-chemical cells composed of an assembly of a solid electrolyte membrane and two low-cost photoelectrodes have been developed to generate green solar fuel from water-splitting. In this regard, an anion-exchange polymer-electrolyte membrane, able to separate H₂ evolved at the photocathode from O₂ at the photoanode, was investigated in terms of ionic conductivity, corrosion mitigation, and light transmission for a tandem photo-electro-chemical configuration. The designed anionic membranes, based on polysulfone polymer, contained positive fixed functionalities on the side chains of the polymeric network, particularly quaternary ammonium species counterbalanced by hydroxide anions. The membrane was first investigated in alkaline solution, KOH or NaOH at different concentrations, to optimize the ion-exchange process. Exchange in 1M KOH solution provided high conversion of the groups, a high ion-exchange capacity (IEC) value of 1.59 meq/g and a hydroxide conductivity of 25 mS/cm at 60 °C for anionic membrane. Another important characteristic, verified for hydroxide membrane, was its transparency above 600 nm, thus making it a good candidate for tandem cell applications in which the illuminated photoanode absorbs the highest-energy photons (< 600 nm), and photocathode absorbs the lowest-energy photons. Furthermore, hydrogen crossover tests showed a permeation of H₂ through the membrane of less than 0.1%. Finally, low-cost tandem photo-electro-chemical cells, formed by titanium-doped hematite and ionomer at the photoanode and cupric oxide and ionomer at the photocathode, separated by a solid membrane in OH form, were assembled to optimize the influence of ionomer-loading dispersion. Maximum enthalpy (1.7%), throughput (2.9%), and Gibbs energy efficiencies (1.3%) were reached by using n-propanol/ethanol (1:1 wt.) as solvent for ionomer dispersion and with a 25 µL cm^-2 ionomer loading for both the photoanode and the photocathode.