Photocatalytic Degradation of Quinoline Yellow over Ag3PO4

Efficient electrochemical hydrogen evolution activity of nanostructured Ag3PO4/MoS2 heterogeneous composite catalyst

Hydrogen (H2) generation by electrochemical water splitting is a key technique for sustainable energy applications. Two-dimensional (2D) transition-metal dichalcogenide (MoS2) and silver phosphate (Ag3PO4) possess excellent electrochemical hydrogen evolution reaction (HER) properties when they are combined together as a composite rather than individuals. Reports examining the HER activity by using Ag3PO4, especially, in combination with the 2D layered MoS2 are limited in literature. The weight fraction of MoS2 in Ag3PO4 is optimized for 1, 3, and 5 wt%. The Ag3PO4/1 wt % MoS2 combination exhibits enhanced HER activity with least overpotential of 235 mV among the other samples in the acidic medium. The synergistic effect of optimal nano-scale 2D layered MoS2 structure and Ag3PO4 is essential for creating higher electrochemical active surface area of 217 mF/cm2, and hence this leads to faster reaction kinetics in the HER. This work suggests the advantages of Ag3PO4/1 wt % MoS2 heterogeneous composite catalyst for electrochemical analysis and HER indicating lower resistivity and low Tafel slope value (179 mV/dec) among the prepared catalysts making it a promising candidate for its use in practical energy applications.

Light-powered swarming phoretic antimony chalcogenide-based microrobots with "on-the-fly" photodegradation abilities

Microrobots are at the forefront of research for biomedical and environmental applications. Whereas a single microrobot exhibits quite low performance in the large-scale environment, swarms of microrobots are representing a powerful tool in biomedical and environmental applications. Here, we fabricated phoretic Sb₂S₃-based microrobots that exhibited swarming behavior under light illumination without any addition of chemical fuel. The microrobots were prepared in an environmentally friendly way by reacting the precursors with bio-originated templates in aqueous solution in a microwave reactor. The crystalline Sb₂S₃ material provided the microrobots with interesting optical and semiconductive properties. Because of the formation of reactive oxygen species (ROS) upon light illumination, the microrobots possessed photocatalytic properties. To demonstrate the photocatalytic abilities, industrially used dyes, quinoline yellow and tartrazine were degraded using microrobots in the "on-the-fly" mode. Overall, this proof-of-concept work showed that Sb₂S₃ photoactive material is suitable for designing swarming microrobots for environmental remediation applications.

Enhanced photocatalytic activity of Fe-, S- and N-codoped TiO2 for sulfadiazine degradation

The composite material based on N-, S-, and Fe-doped TiO2 (NSFe-TiO2) synthesized by wet impregnation was used as a photocatalyst to rapidly degrade sulfadiazine. The photocatalytic degradation behavior and mechanism of sulfadiazine on NSFe-TiO2 were investigated for revealing the role of degradation under ultraviolet light. The results showed that compared with TiO2, NSFe-TiO2 markedly improved the efficiency in photocatalytic degradation of sulfadiazine: more than 90% of sulfadiazine could be removed within 120 min by NSFe-TiO2 dosage of 20 mg L-1. The process conformed to first-order reaction kinetics model. The parameters such as loaded amount of NSFe-TiO2, solution pH value, humic acid concentration and recycle numbers on removal efficiency were also studied. Compared to neutral and alkaline conditions, acidic condition was not conducive to the photocatalysis. HA, Ca2+, Cu2+ and Zn2+ in the actual water body had mild inhibition on sulfadiazine degradation in UV/NSFe-TiO2 system. Fragments screened by high-resolution mass spectrometry were conducted to explore the oxidation mechanism and pathways of sulfadiazine degradation. On the whole, UV/NSFe-TiO2 photocatalysis has a good effect on sulfadiazine removal.

Supplementary Information

The online version contains supplementary material available at 10.1007/s13762-023-04771-6.

Enhanced reactivity of the CuO-Fe2O3 intimate heterojunction for the oxidation of quinoline yellow dye (E104)

This research work describes the degradation of quinoline yellow (QY) in aqueous solutions by the heterogeneous Fenton and photo-Fenton processes in the presence of CuO/Fe₂O₃ photocatalyst. CuO/Fe₂O₃ derived from LDH structure was synthesized by the co-precipitation method. The physiochemical characteristics of CuO/Fe₂O₃ were described by XRD, TEM/SEM, BET surface area, and FTIR techniques. The effects of pH, H₂O₂ concentration, dye concentration, catalyst dose, reaction temperature, and reusability of catalyst on the QY decolorization efficiency were studied. The results indicated that a complete removal of QY was achieved within 150 min, when the H₂O₂ and QY concentrations were 27.6 mM and 100 mg/L, respectively. The rate constants for QY removal by the heterogeneous Fenton system were calculated, and the experimental data were found to fit the pseudo-first order model. Under optimal conditions, the rate constants were, respectively, 0.02032 and 0.01715 min^-1 for the photo-Fenton and Fenton systems; this means that the addition of light has not a noticeable effect.

High efficiency photocatalytic degradation of Ambroxol over Mn doped TiO2: Experimental designs, identification of transformation products, mineralization and mechanism

Ambroxol (AMB) is a drug commonly used for chronic bronchitis prevention. Once released in surface water, this recalcitrant chemical becomes a hazardous pollutant. Here, we investigated the ability of 1% Mn-doped TiO₂ (Mn-TiO₂) to mineralize AMB by photocatalysis. We studied the morphology, and the physical and electrochemical properties of Mn-TiO₂ using X-ray diffraction, Scanning electron microscopy, Transmission electron microscopy, X-ray fluorescence, BET method, UV-visible, and electrochemical study and optimized the AMB degrading experimental conditions through response surface methodology (RSM). Mn-TiO₂ at the dose of 0.625 g·L^-1 allowed the complete photodegradation of AMB (30 ppm) at pH 7 under UVA light irradiation for 30 min while total mineralization in CO₂ (>96%) was achieved after 24 h of irradiation. Mn-TiO₂ was 1.6-time more efficient than TiO₂ Degussa P25. Product studies were also carried out by liquid chromatography coupled to electrospray high resolution mass spectrometry. Twenty-one photodegradation products were detected and identified. In addition, ionic chromatography analyses revealed the release of Br^-, NH₄⁺, and NO₃^- at respectively 97, 63 and 35% of the total Br, and N initially present in AMB. Finally, the reusability of the photocatalyst was also tested. After four cycles, the almost complete photodegradation of AMB was achieved showing that Mn-TiO₂ was highly stable. This work brings new physical characteristics on Mn-TiO₂ photocatalyst. Moreover, it is the first study investigating the photocatalytic degradation of recalcitrant AMB drug.