Improvement of CO2 Photoreduction Efficiency by Process Intensification

Carbon Nitride-Based Catalysts for High Pressure CO2 Photoreduction

In the current research, the productivity of CO2 photoreduction has been boosted by performing the reaction in an innovative photocatalytic reactor, which allows for operation up to 20 bar. A set of photocatalysts were used, including three types of pristine TiO2, i.e., one commercially prepared (Evonik P25), one home-prepared by flame spray pyrolysis (FSP), and one obtained by the hydrolysis of TiCl4 (TiO2exCl), a bare thermo-exfoliated carbon nitride (C3N4-TE), and binary materials composed of TiO2 and C3N4-TE. The photoreduction was carried out in water at pH 14 and in the presence of Na2SO3 as a hole scavenger. Hydrogen and very small amounts of CO were detected in the head space of the photoreactor, while in the liquid phase, the main product was formic acid, along with traces of methanol and formaldehyde. The composites P25/TE and TiO2exCl/TE were found to have a higher productivity if compared to its single constituents used alone, probably due to the heterojunction formed by coupling the two materials. Moreover, the high pressure applied in the photoreactor proved to be very effective in boosting the yield of the organic products.

Visible-Light-Driven CO2 Reduction into Methanol Utilizing Sol-Gel-Prepared CeO2-Coupled Bi2O3 Nanocomposite Heterojunctions

Carbon dioxide (CO2) photoreduction into renewable fuels over semiconductor photocatalysts has emerged as a green and sustainable alternative for energy production. Consequently, tremendous efforts are being performed to develop robust and sustainable photocatalysts. Therefore, visible-light active nanocomposite photocatalysts composed of 5.0–20.0 wt.% bismuth oxide (Bi2O3) and cerium oxide (CeO2) were synthesized by a sol-gel-based process. The prepared nanocomposites were evaluated for the promoted photocatalytic reduction of CO2 into methanol (CH3OH). Various characterizations of the obtained photocatalysts exposed an outstanding development of crystalline structure, morphology, and surface texture due to the presence of Bi2O3. Moreover, the absorbance of light in the visible regime was improved with enhanced charge separation, as revealed by the exploration of optical response, photoluminescence, and photocurrent measurements. The overall bandgap calculations revealed a reduction to 2.75 eV for 15% Bi2O3/CeO2 compared to 2.93 eV for pure CeO2. Moreover, the adjusted 2.8 g L−1 dose of 15% Bi2O3/CeO2 selectively produced 1300 μmol g−1 CH3OH after 9 h of visible light irradiation. This photocatalyst also exhibits bearable reusability five times. The improved progression of 15% Bi2O3/CeO2 is denoted by significant charge separation as well as enhanced mobility. This study suggests the application of metal oxide-based heterojunctions for renewable fuel production under visible light.

In Situ Formation of Z-Scheme Bi2WO6/WO3 Heterojunctions for Gas-Phase CO2 Photoreduction with H2O by Photohydrothermal Treatment

We report a new photohydrothermal method to prepare a Bi2WO6/WO3 catalytic material for CO2 photoreduction by solar concentrators. The photohydrothermal treatment improves the physico-chemical properties of the Bi2WO6/WO3 material and forms well contact Bi2WO6/WO3 heterojunctions, which increase the maximum reaction rate of CO2 photoreduction to 8.2 times under the simulated light, and the hydrocarbon yield under the real concentrating solar light achieves thousands of μmol·gcata−1. The reason for the high activity is attributed to the direct Z-scheme effect of Bi2WO6/WO3 heterojunctions and the photothermal effect during the course. These findings highlight the utilization of solar energy in CO2 photoreduction and open avenues for the rational design of highly efficient photocatalysts.