Advances in Oxidative Desulfurization of Fuel Oils over MOFs-Based Heterogeneous Catalysts

RSM optimization of Friedel-Crafts C-acylation of para-fluorophenol over the catalysis of phosphomolybdic acid encapsulated in MIL-53 (Fe) metal organic frameworks

In this research, a heterogeneous acid catalyst was synthesized by room temperature encapsulation of phosphomolybdic acid (PMA) in the pores of the MIL-53 (Fe) metal organic framework (MOF) under ultrasonic conditions. Then the catalytic activity of PMA@MIL-53 (Fe) was investigated in Friedel-Crafts C-acylation of para-fluorophenol, and this procedure was optimized using response surface methodology based on central composite design (RSM-CCD). The impact of critical reaction parameters including reaction duration, catalyst dosage, and PMA amount in the catalyst was optimized, leading to the formation of the target product in excellent yield at a short reaction time.

Green synthesis of thiourea derivatives from nitrobenzenes using Ni nanoparticles immobilized on triazine-aminopyridine-modified MIL-101(Cr) MOF

Nanohybrid metal-organic frameworks (MOF) have recently been considered next-generation catalysts regarding their unique features like large surface-to-volume ratio, tailorable geometry, uniform pore sizes, and homogeneous distribution of active sites. In this report, we address the triazine-aminopyridine-modified 3D Cr-centred MOF MIL-101(Cr)-NH2 following a post-synthetic modification approach. The excellent chelating ability of triazine-aminopyridine was applied to immobilize Ni ions over the host matrix MOF. The as-synthesized material was physicochemically characterized using various analytical techniques like FT-IR, electron microscopy, EDS, elemental mapping, XRD, and ICP-OES. Subsequently, the material has been catalytically employed in synthesizing new thiourea derivatives by reacting to nitrobenzene derivatives and phenyl isocyanate. The catalyst was isolated by centrifugation and recycled in 6 consecutive runs without momentous loss of its reactivity.

Studies on Synthesis, Characterization, and Photocatalytic Activity of TiO2 and Cr-Doped TiO2 for the Degradation of p-Chlorophenol

TiO₂ and Cr-TiO₂ nanoparticles (NPs) have been synthesized by the sol-gel method using titanium isopropoxide as the precursor of Titania. The prepared samples were analyzed by employing scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and Fourier transform infrared analyses. Under UV irradiation, the photocatalytic activities of TiO₂ and Cr-TiO₂ were observed by estimating the % degradation of p-chlorophenol (PCP) as a sample pollutant. The extent of degradation was investigated, varying the catalyst dosage, initial PCP concentration, irradiation time, and solution pH. The experimental results show that efficiency of catalysts initially increases but decreases later on, whereas the % degradation of PCP is the highest at its lowest initial concentration. For TiO₂ and Cr-TiO₂ NPs at their optimal catalyst dosage of 2.0 g/L, acidic pH, and with UV irradiation for 90 min, the observed % degradation of PCP is 50.23 ± 3.12 and 66.51 ± 2.14%, respectively. Thus, the prepared Cr-TiO₂ NPs have enhanced the degradation efficiency of PCP with an irradiation time which is four time less than those reported earlier. From the kinetics analysis, the degradation reaction of PCP is found to follow a pseudo-first-order model and the rate constants are 0.0075 and 0.0122 min^-1 for pure TiO₂ and Cr-TiO₂ NPs, respectively. The present study has further revealed that owing to the lower rate of electron-hole pair recombination, the photocatalytic activity of Cr-TiO₂ NPs becomes higher than that of TiO₂. Therefore, as viable photocatalytic agents, Cr-TiO₂ NPs are suggested to be used also for efficient degradation of other organic pollutants.

The Progress of Metal-Organic Framework for Boosting CO2 Conversion

With the rapid development of modern society, environmental problems, including excessive amounts of CO2 released in the atmosphere, are becoming more and more serious. It is necessary to develop new materials and technologies to reduce pollution. Among them, metal–organic frameworks (MOFs) have shown potential for application in the area of catalysis due to their ultra-high specific surface area, structural versatility, and designability as well as ease of modification and post-synthesis. Herein, we summarize recent research advances by use of MOFs for boosting CO2 conversion. Furthermore, challenges and possible research directions related to further exploration are also discussed.