Synthesis of Ag3PO4/G-C3N4 Composite with Enhanced Photocatalytic Performance for the Photodegradation of Diclofenac under Visible Light Irradiation

Silver phosphate-modified carbonate apatite honeycomb scaffolds for anti-infective and pigmentation-free bone tissue engineering

Bone regeneration using synthetic materials has a high rate of surgical site infection, resulting in severe pain for patients and often requiring revision surgery. We propose Ag3PO4-based surface modification and structural control of scaffolds for preventing infections in bone regeneration. We demonstrated the differences in toxicity and antibacterial activity between in vitro and in vivo studies and determined the optimal silver content in terms of overall anti-infection effects, bone regeneration, toxicity, and pigmentation. A honeycomb structure comprising osteoconductive and resorbable carbonate apatite (CAp) was used as the base scaffold. CAp in the scaffold surface was partially replaced with different concentrations of Ag3PO4 via controlled dissolution-precipitation reactions in an AgNO3 solution. Both bone regeneration and infection prevention were achieved at 860-2300 ppm of silver. Despite the absence of Ag3PO4, honeycomb scaffolds were less susceptible to infection, even under conditions where infection occurs in clinically used three-dimensional porous scaffolds. Regardless of in vitro cytotoxicity at >5200 ppm of silver, increasing the silver content to 21,000 ppm did not adversely affect in vivo bone formation and scaffold resorption or cause acute systemic toxicity. Rather, bone formation was enhanced with 5200 ppm of silver. However, pigmentation was observed at that concentration. Hence, we concluded that the optimal silver concentration range is 860-2300 ppm for anti-infective and pigmentation-free bone regeneration. Bone regeneration was achieved via surface modification, resulting in the rapid release of silver ions immediately after implantation, followed by gradual release over several months. The scaffold structure may also aid in preventing bacterial growth within the scaffolds.

A fingerprint-like supramolecular-assembled Ag3PO4/polydopamine/g-C3N4 heterojunction nanocomposite for enhanced solar-driven oxygen evolution in vivo

Biocompatible photocatalytic water-splitting systems are promising for tissue self-oxygenation. Herein, a structure-function dual biomimetic fingerprint-like silver phosphate/polydopamine/graphitic carbon nitride (Ag3PO4/PDA/g-C3N4) heterojunction nanocomposite is proposed for enhanced solar-driven oxygen (O2) evolution in vivo in situ. Briefly, a porous nitrogen-defected g-C3N4 nanovoile (CN) is synthesized as the base. Dopamine molecules are controllably inserted into the CN interlayer, forming PDA spacers (4.28 nm) through self-polymerization-induced supramolecular-assembly. Ag3PO4 nanoparticles are then in situ deposited to create Ag3PO4/PDA/CN. The fingerprint-like structure of PDA/CN enlarges the layer spacing, thereby accelerating mass transfer and increasing reaction sites. The PDA spacer roles as excellent light harvester, electronic-ionic conductor, and redox pair through conformational changes, resulting in tailored electronic band structure, optimized carrier behavior, and reduced electrochemical impedance. In physiological conditions, Ag3PO4/PDA/CN exhibits O2 evolution rate of 45.35 μmol⋅g-1⋅h-1, 9-fold of bulk g-C3N4. The biocompatibility and in vivo oxygen supply effectiveness for biomedical applications have been verified in animal models.

Efficient electrochemical hydrogen evolution activity of nanostructured Ag3PO4/MoS2 heterogeneous composite catalyst

Hydrogen (H2) generation by electrochemical water splitting is a key technique for sustainable energy applications. Two-dimensional (2D) transition-metal dichalcogenide (MoS2) and silver phosphate (Ag3PO4) possess excellent electrochemical hydrogen evolution reaction (HER) properties when they are combined together as a composite rather than individuals. Reports examining the HER activity by using Ag3PO4, especially, in combination with the 2D layered MoS2 are limited in literature. The weight fraction of MoS2 in Ag3PO4 is optimized for 1, 3, and 5 wt%. The Ag3PO4/1 wt % MoS2 combination exhibits enhanced HER activity with least overpotential of 235 mV among the other samples in the acidic medium. The synergistic effect of optimal nano-scale 2D layered MoS2 structure and Ag3PO4 is essential for creating higher electrochemical active surface area of 217 mF/cm2, and hence this leads to faster reaction kinetics in the HER. This work suggests the advantages of Ag3PO4/1 wt % MoS2 heterogeneous composite catalyst for electrochemical analysis and HER indicating lower resistivity and low Tafel slope value (179 mV/dec) among the prepared catalysts making it a promising candidate for its use in practical energy applications.

Photocatalytic Degradation of Ceftriaxone Using TiO2 Coupled with ZnO Micronized by Supercritical Antisolvent Route

Heterogeneous photocatalysis is a promising technique for removing pollutants from water. In this work, supercritical antisolvent (SAS)-micronized ZnO (ZnOSAS) is coupled with commercial anatase TiO2 (PC50) to study the photocatalytic degradation of ceftriaxone under UV and visible light. Diffuse ultraviolet-visible reflectance (UV-vis DRS) measurement revealed that the presence of ZnO leads to a slight absorption in the visible region. Wide-angle X-ray diffraction (WAXD) analysis showed the presence of both ZnO wurtzite and TiO2 anatase crystalline phases in the composite. Photocatalytic tests proved that the activity of the ZnOSAS/PC50 composite is higher than that of commercial ZnO, SAS-micronized ZnO, and PC50, allowing complete ceftriaxone degradation under UV light after only 2 min of irradiation time. In contrast, about 90% of ceftriaxone degradation is achieved after 180 min of visible-light irradiation. The photocatalytic results for an experiment carried out in the presence of probe scavenger molecules for reactive oxygen species show that hydroxyl radicals and positive holes are both reactive species involved in the ceftriaxone photocatalytic degradation mechanism. Finally, reuse cycles of the ZnOsas/PC50 composite are performed, demonstrating the stability and recyclability of the photocatalyst.

Investigation of the photocatalytic and optical properties of the SrMoO4/g-C3N4 heterostructure obtained via sonochemical synthesis with temperature control

In this work, nanomaterials of the SrMoO₄/g-C₃N₄ heterostructure were synthesized in a single step by the sonochemical method with controlled temperatures. Structural and morphological investigations indicate the formation of heterojunctions, revealing the presence of g-C₃N₄ (CN) in the heterostructures and an interface region between the phases. Optical analyzes show broadening of the wavelength absorption range and a decrease in the photoluminescence (PL) intensity of the heterojunctions compared to the CN emission spectrum, proving a decrease in the recombination of the photogenerated charges. The results of the photocatalytic tests indicate that the insertion of CN promoted photocatalytic degradation of the Methylene Blue (MB), Rhodamine B (RhB) and Crystal Violet (CV) organic contaminants, up to 99.58%, 100% and 98.65%, respectively. The mixture of dyes used and reuse cycles was performed to analyze the applicability of the compounds in a real situation.

Rapid Synthesis Method of Ag3PO4 as Reusable Photocatalytically Active Semiconductor

The widespread use of Ag₃PO₄ is not surprising when considering its higher photostability compared to other silver-based materials. The present work deals with the facile precipitation method of silver phosphate. The effects of four different phosphate sources (H₃PO₄, NaH₂PO₄, Na₂HPO₄, Na₃PO₄·12 H₂O) and two different initial concentrations (0.1 M and 0.2 M) were investigated. As the basicity of different phosphate sources influences the purity of Ag₃PO₄, different products were obtained. Using H₃PO₄ did not lead to the formation of Ag₃PO₄, while applying NaH₂PO₄ resulted in Ag₃PO₄ and a low amount of pyrophosphate. The morphological and structural properties of the obtained samples were studied by X-ray diffractometry, diffuse reflectance spectroscopy, scanning electron microscopy, infrared spectroscopy, and X-ray photoelectron spectroscopy. The photocatalytic activity of the materials and the corresponding reaction kinetics were evaluated by the degradation of methyl orange (MO) under visible light. Their stability was investigated by reusability tests, photoluminescence measurements, and the recharacterization after degradation. The effect of as-deposited Ag nanoparticles was also highlighted on the photostability and the reusability of Ag₃PO₄. Although the deposited Ag nanoparticles suppressed the formation of holes and reduced the degradation of methyl orange, they did not reduce the performance of the photocatalyst.

Phosphor-Enhanced, Visible-Light-Storing g-C3N4/Ag3PO4/SrAl2O4:Eu2+,Dy3+ Photocatalyst Immobilized on Fractal 3D-Printed Supports

The combination of a phosphor with semiconductor photocatalysts can provide photoactivity in the dark. Indeed, the phosphor acts as a "light battery", harvesting photons during irradiation and later re-emitting light that can be used by the catalytic phase when in conditions of total darkness. This allows for continued activity of the composite catalyst, even in conditions of unstable light stimulation. In this study, we assess the use of a heterojunction, namely graphitic-C₃N₄/Ag₃PO₄, that enables efficient photoactivity specifically under visible light stimulation, in combination with a phosphor that exhibits green-blue phosphorescence (510 nm), that is SrAl₂O₄:Eu²⁺,Dy³⁺. Our findings showed that this combination was particularly interesting, noticeably displaying significant photoactivity in darkness, after short periods of activation by visible light. After finding the right combination and optimal ratios for maximum efficiency, the resulting catalyst composite was immobilized on resin supports with a fractal surface, printed by LCD-SLA 3D printing. The immobilization was effectuated via an aqueous-phase plasma-aided grafting (APPAG) process, using cold plasma discharge (CPD) and using vinylphosphonic acid (VPA) as a coupling agent. Whereas the colloidal photocatalyst displayed a serious problem of partial physical separation between the catalytic phase, g-C₃N₄/Ag₃PO₄, and the phosphor, the immobilization of the composite catalyst on polymer supports allowed solving this issue. Photodegradation assessments confirmed that the hybrid supported phosphor-enhanced catalyst was active, notably in dark conditions, as well as fairly photostable. This study offers new prospects for the fabrication of polymer-based panels for water purification, with round-the-clock activity and that are, in addition, extremely easy to recover and reuse, by comparison with colloidal catalysts.

Graphene/silver-based composites and coating on dead coral for degradation of organic pollution using the Z-scheme mechanism

A high-performance photocatalytic nanocomposite consisting of silver phosphate-based particles with GO and RGO was synthesized by co-precipitation and hydrothermal methods. Ag₃PO₄ was prepared by a co-precipitation method. The as-prepared Ag₃PO₄ nanocomposites were characterized by different analyses. The results demonstrated that the Ag₃PO₄ particles were well dispersed on the graphene-based surfaces. The photocatalytic performance of the GO/RGO/Ag₃PO₄ nanocomposite was evaluated for the photodegradation of methylene blue (MB) under exposure to visible light (xenon lamp λ > 400 nm). The degradation rate was about 98% in 5 min. The enhancement in photocatalytic performance is attributed to the simultaneous presence of RGO and GO, which show significantly high absorption of organic molecules on the surface of GO/RGO, allowing the effective transfer and separation of photogenerated electrons. In addition, this modified structure can be in situ synthesized on dead coral structures that can be used in future real case-studies of the degradation of other organic pollutants. The ingredient of these composites, however, is about 93% Ag₃PO₄.

A high-performance photocatalytic nanocomposite consisting of silver phosphate-based particles with GO and RGO was synthesized by co-precipitation and hydrothermal methods.

Uncertainty and misinterpretation over identification, quantification and transformation of reactive species generated in catalytic oxidation processes: A review

The identification of reactive radical species using quenching and electron paramagnetic resonance (EPR) tests has attracted extensive attention, but some mistakes or misinterpretations are often present in recent literature. This review aims to clarify the corresponding issues through surveying literature, including the uncertainty about the identity of radicals in the bulk solution or adsorbed on the catalyst surface in quenching tests, selection of proper scavengers, data explanation for incomplete inhibition, the inconsistent results between quenching and EPR tests (e.g., SO₄^•- is predominant in quenching test while the signal of ^•OH predominates in EPR test), and the incorrect identification of EPR signals (e.g., SO₄^•- is identified by indiscernible or incorrect signals). In addition, this review outlines the transformation of radicals for better tracing the origin of radicals. It is anticipated that this review can help in avoiding mistakes while investigating catalytic oxidative mechanism with quenching and EPR tests.

Transition element doped octahedral manganese molecular sieves (Me-OMS-2) as diclofenac adsorbents

Diclofenac (DCF) control measures have become an area of increased interest for environmental researchers due to the high environmental concentration and risk of DCF. Adsorption seems to be promising for DCF removal from the aqueous phase because of its specific superiority in comparison with biodegradation, membrane separation, and advanced oxidation or reduction. In this study, OMS-2 and metal-doped OMS-2 ((Me-OMS-2, with Me = Co, Cu or Ce) were prepared and tested as adsorbents for the removal of DCF. It was evident that the maximum adsorption capacity and rate of Ce-OMS-2 were much higher than those of the other adsorbents, which could be attributed to its large specific surface area and stereoscopic aperture structure. The experimental data are fitted the pseudo-second-order model, the Elovich equation and the Langmuir model well; moreover, the process is an endothermic and spontaneous thermodynamic process, during which the entropy increased, based on the experimental results, indicating that chemisorption was dominant during the DCF adsorption process onto Ce-OMS-2. By the integral of the peak deconvoluted from the XPS spectrum, the ratio of Mn³⁺/Mn⁴⁺ increased from 0.393 to 0.407, revealing that Mn(IV) is rarely reduced into Mn(III) during the DCF adsorption process.

Photocatalytic Properties of g-C3N4–Supported on the SrAl2O4:Eu,Dy/SiO2

Graphitic carbon nitride (g-C3N4) was supported on SrAl2O4:Eu,Dy-SiO2 by a colloidal-sol coating method to improve its light absorption property. Transmission electron microscopy (TEM) revealed that the nanoparticles of g-C3N4 were coated on sub-micron phosphor particles and nanoscale surface roughness was imparted by the SiO2-binder. Photoluminescence (PL) spectrum of the g-C3N4 supported on SrAl2O4:Eu,Dy exhibited a broadband emission from 400 to 650 nm. Increasing silica-binder in the g-C3N4/SrAl2O4:Eu,Dy composites suppressed the PL emission peak at 525 nm for SrAl2O4:Eu,Dy. Photocatalytic degradation activity was evaluated with 5 ppm methylene blue (MB) solutions under germicidal ultraviolet (UV) and visible (Vis) solar light illuminations. The UV/Vis photocatalytic efficiency was improved by supporting g-C3N4 on the SrAl2O4:Eu,Dy phosphor and with the addition of SiO2 as a binder. In addition, low silica addition effectively improved the adhesiveness of the g-C3N4 coating on the SrAl2O4:Eu,Dy surface. Recyclability tests of photocatalysis for the SrAl2O4:Eu,Dy-0.01M SiO2/50wt% g-C3N4 composites exhibited a remarkable stability by maintaining the degradation efficiencies above 90% in four cycles. Therefore, the composite of g-C3N4-supported SrAl2O4:Eu,Dy-SiO2 is a prospective photocatalyst activating under UV/Vis light irradiation for the elimination of environmental pollutants.

Microwave- and Formaldehyde-Assisted Synthesis of Ag-Ag3PO4 with Enhanced Photocatalytic Activity for the Degradation of Rhodamine B Dye and Crude Oil Fractions

The release of crude oil and water-soluble dyes into our marine environment is a major global problem. An efficient semiconductor Ag-Ag₃PO₄ photocatalyst was synthesized using formaldehyde as a reducing agent to form surface active Ag on Ag₃PO₄ under microwave radiation for heating, and its potential in destroying environmental pollutants has been examined. The diffuse reflectance spectroscopy of Ag-Ag₃PO₄ revealed an enhanced absorption in the visible light region. The rate of photocatalytic degradation of rhodamine B by Ag-Ag₃PO₄ was over 4-fold compared to Ag₃PO₄. The potential application of Ag-Ag₃PO₄ in oil spill remediation was also examined through photocatalytic degradation of benzene, n-hexane, and 1:1 v/v benzene/methanol crude oil-soluble fractions. UV-vis and gas chromatography-mass spectrometry analysis of the crude oil components after visible light irradiation showed excellent degradation. The photocatalytic efficiency enhancement of Ag-Ag₃PO₄ is attributed to the excellent electron trapping of silver nanoparticles deposited on the surface of Ag₃PO₄. This work will motivate future studies to develop recyclable visible light photocatalysts for many applications.

Enhanced photoelectrochemical performance of NaNbO3 nanofiber photoanodes coupled with visible light active g-C3N4 nanosheets for water splitting

Sodium niobate nanofibers (NaNbO₃-NF) have been synthesized using a hydrothermal technique and further coupled with visible light responsive graphitic carbon nitride (g-C₃N₄) nanosheets in different concentration ratios of 2:1 (2-CN), 4:1 (4-CN) and 8:1 (8-CN). A significant improvement in the photoelectrochemical (PEC) performance of the g-C₃N₄/NaNbO₃-NF (4-CN) nanostructured photoanode compared to the bare NaNbO₃ photoanode is observed. A current density of 12.55 mA cm^-2 at 1 V with respect to the Ag/AgCl reference electrode is achieved for the g-C₃N₄/NaNbO₃-NF (4-CN) photoanode, which is ∼3 times higher than the NaNbO₃-NF photoanode. Also, compared to NaNbO₃-NF, the g-C₃N₄/NaNbO₃-NF (4-CN) nanocomposite photoanode showed ∼3 times improvement in the incident photon-to-current conversion efficiency. The improvement in the PEC performance of visible light active g-C₃N₄/NaNbO₃-NF (4-CN) nanocomposite is attributed to the improved photoresponse of NaNbO₃-NF due to the coupling of g-C₃N₄ and the formation of a type-II heterojunction between them leading to the enhanced separation of the photogenerated charge carriers. A possible reaction mechanism for the improved PEC water splitting performance has been proposed for the g-C₃N₄/NaNbO₃-NF (4-CN) photoanode.

Photocatalytic Degradation of Diclofenac Using Al2O3-Nd2O3 Binary Oxides Prepared by the Sol-Gel Method

This paper reports the sol-gel synthesis of Al2O3-Nd2O3 (Al-Nd-x; x = 5%, 10%, 15% and 25% of Nd2O3) binary oxides and the photodegradation of diclofenac activated by UV light. Al-Nd-based catalysts were analyzed by N2 physisorption, XRD, TEM, SEM, UV-Vis and PL spectroscopies. The inclusion of Nd2O3 in the aluminum oxide matrix in the 10-25% range reduced the band gap energies from 3.35 eV for the γ-Al2O3 to values as low as 3.13-3.20 eV, which are typical of semiconductor materials absorbing in the UV region. γ-Al2O3 and Al-Nd-x binary oxides reached more than 92.0% of photoconverted diclofenac after 40 min of reaction. However, the photocatalytic activity in the diclofenac degradation using Al-Nd-x with Nd2O3 contents in the range 10-25% was improved with respect to that of γ-Al2O3 at short reaction times. The diclofenac photoconversion using γ-Al2O3 was 63.0% at 10 min of UV light exposure, whereas Al-Nd-15 binary oxide reached 82.0% at this reaction time. The rate constants determined from the kinetic experiments revealed that the highest activities in the aqueous medium were reached with the catalysts with 15% and 25% of Nd2O3, and these compounds presented the lowest band gap energies. The experimental results also demonstrated that Nd2O3 acts as a separator of charges favoring the decrease in the recombination rate of electron-hole pairs.

Colorimetric sensing of chlorpyrifos through negative feedback inhibition of the catalytic activity of silver phosphate oxygenase nanozymes

Intensive use of organophosphate chlorpyrifos pesticides in farming has become a serious issue due to their harmful effects on living beings. Most fruits, vegetables and soil contain chlorpyrifos, and it cannot be rinsed out completely by water washing. Therefore, a selective and sensitive detection of chlorpyrifos is significant. In the present study, the intriguing oxidase-mimicking activity of Ag₃PO₄ nanoparticles (NPs) is explored for the fast and selective detection of chlorpyrifos pesticides. Ag₃PO₄ NPs exhibit several advantages, such as great catalytic efficiency, high stability, monodispersity and reusability, over other expensive nanozymes via a facile one-step sensing. The size, shape, crystal planes and diffraction patterns of the Ag₃PO₄ NPs were observed via FESEM and HR-TEM. The surface properties and oxidation states were analyzed via XPS technique. Ag₃PO₄ NPs possess intrinsic excellent oxidase-mimicking properties against 3,3′,5,5′-tetramethylbezidyne (TMB). When chlorpyrifos and Ag₃PO₄ NP nanozymes come in proper orientation proximity, chlorpyrifos is oxidized. The oxidized chlorpyrifos produces sulfide ions and chlorpyrifos oxon. The produced sulfide ions in the reaction system interact with Ag₃PO₄ NPs and inhibit their catalytic activity by feedback inhibition. Indeed, neither any catalytic site is left to oxidize TMB nor any blue colour appears. Thus, this feedback inhibition phenomenon senses chlorpyrifos pesticides. The calculated limit of detection (LOD) for the standard chlorpyrifos is ∼9.97 ppm, and the efficacy of the Ag₃PO₄ NPs calculated in terms of the K_m value was found to be 0.15 mM. A real sample analysis was carried out by the standard addition method with two soil samples collected from Pethapur and Chiloda villages.

Ag₃PO₄ oxygenase nanozymatic activity towards chlorpyrifos sensing.

One-Pot Synthesized Visible Light-Driven BiOCl/AgCl/BiVO4 n-p Heterojunction for Photocatalytic Degradation of Pharmaceutical Pollutants

A novel enhanced visible light absorption BiOCl/AgCl/BiVO₄ heterojunction of photocatalysts could be obtained through a one-pot hydrothermal method used with two different pH solutions. There was a relationship between synthesis pH and the ratio of BiOCl to BiVO₄ in XRD planes and their photocatalytic activity. The visible light photocatalytic performances of photocatalysts were evaluated via degradation of diclofenac (DCFF) as a pharmaceutical model pollutant. Furthermore, kinetic studies showed that DCF degradation followed pseudo-first-order kinetics. The photocatalytic degradation rates of BiOCl/AgCl/BiVO₄ synthesized at pH = 1.2 and pH = 4 for DCF were 72% and 47%, respectively, showing the higher activity of the photocatalyst which was synthesized at a lower pH value. It was concluded that the excellent photocatalytic activity of BiOCl/AgCl/BiVO₄ is due to the enhanced visible light absorption formation of a heterostructure, which increased the lifetime of photo-produced electron–hole pairs by creating a heterojunction. The influence of pH during synthesis on photocatalytic activity in order to create different phases was investigated. This work suggests that the BiOCl/AgCl/BiVO₄ p-n heterojunction is more active when the ratio of BiOCl to BiVO₄ is smaller, and this could be achieved simply by the pH adjustment. This is a promising method of modifying the photocatalyst for the purpose of pollutant degradation under visible light illumination.

Carbon nitrides and metal nanoparticles: from controlled synthesis to design principles for improved photocatalysis

The use of sunlight to drive chemical reactions via photocatalysis is of paramount importance towards a sustainable future. Among several photocatalysts, earth-abundant polymeric carbon nitride (PCN, often wrongly named g-C3N4) has emerged as an attractive candidate due to its ability to absorb light efficiently in the visible and near-infrared ranges, chemical stability, non-toxicity, straightforward synthesis, and versatility as a platform for constructing hybrid materials. Especially, hybrids with metal nanoparticles offer the unique possibility of combining the catalytic, electronic, and optical properties of metal nanoparticles with PCN. Here, we provide a comprehensive overview of PCN materials and their hybrids, emphasizing heterostructures with metal nanoparticles. We focus on recent advances encompassing synthetic strategies, design principles, photocatalytic applications, and charge-transfer mechanisms. We also discuss how the localized surface plasmon resonance (LSPR) effect of some noble metals NPs (e.g. Au, Ag, and Cu), bimetallic compositions, and even non-noble metals NPs (e.g., Bi) synergistically contribute with PCN in light-driven transformations. Finally, we provide a perspective on the field, in which the understanding of the enhancement mechanisms combined with truly controlled synthesis can act as a powerful tool to the establishment of the design principles needed to take the field of photocatalysis with PCN to a new level, where the desired properties and performances can be planned in advance, and the target material synthesized accordingly.

A Facile Synthesis of Visible-Light Driven Rod-on-Rod like α-FeOOH/α-AgVO3 Nanocomposite as Greatly Enhanced Photocatalyst for Degradation of Rhodamine B

In this work, we have synthesized the rod-on-rod–like α-FeOOH/α-AgVO3 nanocomposite photocatalysts with the different amounts of solvothermally synthesized α-FeOOH nanorods via a simple co-precipitation method. The as-synthesized photocatalysts were characterized by X-ray diffraction (XRD), Fourier-transform infrared (FT-IR) spectroscopy, UV−Visible diffuse reflectance spectroscopy, scanning electron microscopy (SEM), element mapping, high-resolution transmission electron microscopy (HR-TEM) and X-ray photoelectron spectroscopy (XPS) analysis. The observed SEM images show that both α-AgVO3 and α-FeOOH exhibits the rod-shaped morphology with nano size. Furthermore, the photocatalytic activities of the obtained photocatalysts were evaluated towards the degradation of Rhodamine B (RhB) under visible-light irradiation. It is demonstrated that the 3 mg α-FeOOH added to the α-FeOOH/α-AgVO3 nanocomposite exhibited an enhanced photocatalytic performance as compared with the pure α-AgVO3 and α-FeOOH. This significant improvement can be attributed to the increased photo-excited electron-hole pair separation efficiency, large portion of visible-light absorption ability and the reduced recombination of the electron-hole pair. The recycling test revealed that the optimized nanocomposite exhibited good photostability and reusability properties. In addition, the believable photodegradation mechanism of RhB using α-FeOOH/α-AgVO3 nanocomposite is proposed. Hence, the developed α-FeOOH/α-AgVO3 nanocomposite is a promising material for the degradation of organic pollutants in an aqueous environment.

Quantum dot-decorated semiconductor micro- and nanoparticles: A review of their synthesis, characterization and application in photocatalysis

Quantum dot (QD)-decorated semiconductor micro- and nanoparticles are a new class of functional nanomaterials that have attracted considerable interest for their unique structural, optical and electronic properties that result from the large surface-to-volume ratio and the quantum confinement effect. In addition, because of QDs' excellent light-harvesting capacity, unique photoinduced electron transfer, and up-conversion behaviour, semiconductor nanoparticles decorated with quantum dots have been used widely in photocatalytic applications for the degradation of organic pollutants in both the gas and aqueous phases. This review is a comprehensive overview of the recent progress in synthesis methods for quantum dots and quantum dot-decorated semiconductor composites with an emphasis on their composition, morphology and optical behaviour. Furthermore, various approaches used for the preparation of QD-based composites are discussed in detail with respect to visible and UV light-induced photoactivity. Finally, an outlook on future development is proposed with the goal of overcoming challenges and stimulating further research into this promising field.