Titanium Dioxide/Graphene and Titanium Dioxide/Graphene Oxide Nanocomposites: Synthesis, Characterization and Photocatalytic Applications for Water Decontamination

Design, Characterization, and Evaluation of Textile Systems and Coatings for Sports Use: Applications in the Design of High-Thermal Comfort Wearables

Exposure to high temperatures during indoor and outdoor activities increases the risk of heat-related illness such as cramps, rashes, and heatstroke (HS). Fatal cases of HS are ten times more common than serious cardiac episodes in sporting scenarios, with untreated cases leading to mortality rates as high as 80%. Enhancing thermal comfort can be achieved through heat loss in enclosed spaces and the human body, utilizing heat transfer mechanisms such as radiation, conduction, convection, and evaporation, which do not require initial energy input. Among these, two primary mechanisms are commonly employed in the textile industry to enhance passive cooling: radiation and conduction. The radiation approach encompasses two aspects: (1) reflecting solar spectrum (SS) wavelengths and (2) transmitting and emitting in the atmospheric window (AW). Conduction involves dissipating heat through materials with a high thermal conductivity. Our study focuses on the combined effect of these radiative and conductive approaches to increase thermal energy loss, an area that has not been extensively studied to date. Therefore, the main objective of this project is to develop, characterize, and evaluate a nanocomposite polymeric textile system using electrospinning, incorporating graphene oxide (GO) nanosheets and titanium dioxide nanoparticles (TiO2 NPs) within a recycled polyethylene terephthalate (r-PET) matrix to improve thermal comfort through the dissipation of thermal energy by radiation and conduction. The textile system with a 5:1 molar ratio between TiO2 NPs and GO demonstrates 89.26% reflectance in the SS and 98.40% transmittance/emittance in the AW, correlating to superior cooling performance, with temperatures 20.06 and 1.27 °C lower than skin temperatures outdoors and indoors, respectively. Additionally, the textile exhibits a high thermal conductivity index of 0.66 W/m K, contact angles greater than 120°, and cell viability exceeding 80%. These findings highlight the potential of the engineered textiles in developing high-performance sports cooling fabrics, providing significant advancements in thermal comfort and safety for athletes.

Preparation of Soybean Dreg-Based Biochar@TiO2 Composites and the Photocatalytic Degradation of Aflatoxin B1 Exposed to Simulated Sunlight Irradiation

Aflatoxin B1 (AFB1) is a highly toxic carcinogen severely harmful to humans and animals. This study fabricated SDB-6-K-9@TiO2 composites via the hydrothermal synthesis method to reduce AFB1. The structural characterization results of the photocatalytic composites showed that TiO2 was successfully loaded onto SDB-6-K-9. The different photocatalytic degradation conditions, photocatalyst kinetics, recycling performance, and photocatalytic degradation mechanism were investigated. Photocatalysis with 6 mg of 4%SDB-6-K-9@TiO2 in a 100 μg/mL AFB1 solution presented a reduction of over 95%, exhibiting excellent performance, high stability, and reusability even after five cycles of photocatalytic experiments. Active species trapping experiments confirmed that holes (h+) played the most critical role. After structural analysis and identification of the photocatalytic degradation products, the photodegradation path and photocatalytic oxidation mechanism of 4%SDB-6-K-9@TiO2 were postulated. The results show a new way to improve TiO2's photocatalytic performance, providing a certain theoretical basis for the effective AFB1 reduction.

Sol-Gel-Derived TiO2 and TiO2/Cu Nanoparticles: Synthesis, Characterization, and Antibacterial Efficacy

This study reports on the antibacterial efficacy of both the TiO2 and TiO2/Cu nanoparticles prepared through the sol-gel method. The materials were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TGA), and Brunauer-Emmett-Teller (BET) analysis. The SEM and TEM showed the spherical morphology of the nanoparticles, while EDX and XPS confirmed the incorporation of Cu into the TiO2 nanoparticles. The XRD confirmed the formation of the tetragonal anatase phase of TiO2/Cu while the FTIR revealed the functional groups linked to the doped TiO2 nanoparticles. The thermal stability of TiO2/Cu was found to be lower than pure TiO2. Moreover, TiO2 and the doped TiO2 nanoparticles were notably effective against Bacillus subtilis(B. subtilis) andEscherichia coli(E. coli); however, the addition of Cu to TiO2 did not have any effect on the antibacterial activity probably due to the lower weight content in the composites. Interestingly, the antibacterial efficiency was determined to be 90 and 80% against B. subtilis and E. coli, respectively.

Cleaner Biofuel Production via Process Parametric Optimization of Nonedible Feedstock in a Membrane Reactor Using a Titania-Based Heterogeneous Nanocatalyst: An Aid to Sustainable Energy Development

Membrane technology has been embraced as a feasible and suitable substitute for conventional time- and energy-intensive biodiesel synthesis processes. It is ecofriendly, easier to run and regulate, and requires less energy than conventional approaches, with excellent stability. Therefore, the present study involved the synthesis and application of a highly reactive and recyclable Titania-based heterogeneous nanocatalyst (TiO2) for biodiesel production from nonedible Azadhiracta indica seed oil via a membrane reactor, since Azadhiracta indica is easily and widely accessible and has a rich oil content (39% w/w). The high free fatty acids content (6.52 mg/g KOH) of the nonedible oil was decreased to less than 1% via two-step esterification. Following the esterification, transesterification was performed using a heterogeneous TiO2 nanocatalyst under optimum conditions, such as a 9:1 methanol-oil molar ratio, 90 °C reaction temperature, 2 wt.% catalyst loading, and an agitation rate of 600 rpm, and the biodiesel yield was optimized through response surface methodology (RSM). Azadhiracta indica seed oil contains 68.98% unsaturated (61.01% oleic acid, 8.97% linoleic acid) and 31.02% saturated fatty acids (15.91% palmitic acid, 15.11% stearic acid). These fatty acids transformed into respective methyl esters, with a total yield up to 95% achieved. The biodiesel was analyzed via advanced characterization techniques like gas chromatography-mass spectrometry (GC-MS), Fourier transform infrared spectroscopy (FT-IR), and nuclear magnetic resonance (NMR), whereas the catalyst was characterized via X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), and Fourier transform infrared spectroscopy (FT-IR). Due to its physicochemical properties, Azadirachta indica seed oil is a highly recommended feedstock for biodiesel production. Moreover, it is concluded that the Titania-based heterogeneous nanocatalyst (TiO2) is effective for high-quality liquid fuel synthesis from nonedible Azadirachta indica seed oil in a membrane reactor, which could be an optional green route to cleaner production of bioenergy, eventually leading to sustenance, robustness, and resilience that will aid in developing a holistic framework for integrated waste management.

Computational Study of H2O Adsorption, Hydrolysis, and Water Splitting on (ZnO)3 Nanoclusters Deposited on Graphene and Graphene Oxides

Graphene and graphene oxide (GO)-based metal oxides could play an important role in using metal oxide like zinc oxide (ZnO) as photocatalysts to split water. The π conjugation structure of GO shows greater electron mobility and could enhance the photocatalytic performance of the bare ZnO catalyst by increasing the electron-hole separation. In this work, we use density functional theory (DFT) with the B3LYP exchange functional and DGDZVP2 basis set to study the impact of adsorbing (ZnO)3 nanoparticles on graphene and four different GO models (GO1, GO2, GO4, and GO5) on the hydration and hydrolysis of water that precedes water splitting to produce H2 and O2 atoms in the gas phase and compare them with our previous studies on the bare catalyst in the absence of the substrate. The potential energy curves and activation energies are similar, but the triplet states are lower in energy than the singlet states in contrast to the bare (ZnO)3 catalyst. We extend our calculations to water splitting from the hydrolyzed (ZnO)3 on GO1 (GO1-(ZnO)3). The triplet state energy remains lower than the singlet state energy, and hydrogen production precedes the formation of oxygen, but there is no energy inter-crossing during the formation of O2 that occurs in the absence of a GO1 substrate. Although the hydrolysis reaction pathway follows similar steps in both the bare and GO1-(ZnO)3, water splitting with (ZnO)3 absorbed on the GO1 substrate skips two steps as it proceeds toward the production of the second H2. The production of two hydrogen molecules precedes oxygen formation during water splitting, and the first Zn-H bond formation step is the rate-determining step. The ZnO trimer deposited on GO systems could be potentially attractive nanocatalysts for water splitting.

Thin-Film Nanocomposite (TFN) Membranes for Water Treatment Applications: Characterization and Performance

Thin-film nanocomposite (TFN) membranes have been widely investigated for water treatment applications due to their promising performance in terms of flux, salt rejection, and their antifouling properties. This review article provides an overview of the TFN membrane characterization and performance. It presents different characterization techniques that have been used to analyze these membranes and the nanofillers within them. The techniques comprise structural and elemental analysis, surface and morphology analysis, compositional analysis, and mechanical properties. Additionally, the fundamentals of membrane preparation are also presented, together with a classification of nanofillers that have been used so far. The potential of TFN membranes to address water scarcity and pollution challenges is significant. This review also lists examples of effective TFN membrane applications for water treatment. These include enhanced flux, enhanced salt rejection, antifouling, chlorine resistance, antimicrobial properties, thermal stability, and dye removal. The article concludes with a synopsis of the current status of TFN membranes and future perspectives.

A review on pollutants remediation competence of nanocomposites on contaminated water

Clean freshwater has been required for drinking, sanitation, agricultural activities, and industry, as well as for the development and maintenance of the eco - systems on which all livelihoods rely. Water contamination is currently a significant concern for researchers all over the world; hence it is essential that somehow this issue is resolved as soon as possible. It is now recognised as one of the most important research areas in the world. Current wastewater treatment techniques degrade a wide range of wastewaters efficiently; however, such methods have some limitations. Recently, nanotechnology has emerged as a wonderful solution, and researchers are conducting research in this water remediation field with a variety of potential applications. The pollutants remediation capability of nanocomposites as adsorbents, photocatalysts, magnetic separation, and so on for contaminant removal from contaminated water has been examined in this study. This study has spotlighted the most significant nanocomposites invention reported to date for contaminated and effluent remediation, as well as a research gap as well as possible future perspectives.

Synthesis and enhanced photocatalytic application of porous nanocomposites of (r)GO/TiO2 embedded HCP (hyper crosslinked polymer)

Nanocomposites (r)GO/TiO₂/hyper crosslinked polymer (HCP) were prepared using ultrasonic-assisted method, and identified by (SEM), (EDS), (TEM), and (XRD) techniques. This study was performed to examine the effect of various operating parameters on photocatalytic degradation of Rhodamine B (Rh.B) over (r)GO/TiO₂ embedded HCP followed by an optimization study using response surface methodology (RSM) based on Box-Behnken design (BBD). The photocatalytic activity of rGO/TiO₂/polycalix[4]resorcinarene ((r)GTP) was evaluated using the cationic dye Rhodamine B as a pollutant model under solar light (intensity = 850 W/m²) between 10 and 12 am, June, Ahvaz, Iran. Response Surface Methodology was adopted for the optimization of degradation parameters viz pH, dye concentration, and nanocomposites dosage and contact time. The optimum values for the maximum Rhodamine B (Rh B) degradation of rGO/TiO₂/polycalix (rGTP) and GTP were obtained, in which the degradation of rGTP was 100% and the degradation efficiency of GO/TiO₂/polycalix (GTP) was 70%. ANOVA analysis results demonstrated that irradiation time and nanocomposite mass were the most significant parameters. It was found that rGO/TiO₂/polycalix[4]resorcinarene (rGTP) nanocomposite displayed the best degradation yield for the dye. The results showed that the rGTP nanocomposite displayed good EIS and CV properties besides being eco-friendly and reusable. It could also show a high capacity for the elimination of the dye in the industrial wastewaters.

An Insight into Carbon Nanomaterial-Based Photocatalytic Water Splitting for Green Hydrogen Production

At present, the energy shortage and environmental pollution are the burning global issues. For centuries, fossil fuels have been used to meet worldwide energy demand. However, thousands of tons of greenhouse gases are released into the atmosphere when fossil fuels are burned, contributing to global warming. Therefore, green energy must replace fossil fuels, and hydrogen is a prime choice. Photocatalytic water splitting (PWS) under solar irradiation could address energy and environmental problems. In the past decade, solar photocatalysts have been used to manufacture sustainable fuels. Scientists are working to synthesize a reliable, affordable, and light-efficient photocatalyst. Developing efficient photocatalysts for water redox reactions in suspension is a key to solar energy conversion. Semiconductor nanoparticles can be used as photocatalysts to accelerate redox reactions to generate chemical fuel or electricity. Carbon materials are substantial photocatalysts for total WS under solar irradiation due to their high activity, high stability, low cost, easy production, and structural diversity. Carbon-based materials such as graphene, graphene oxide, graphitic carbon nitride, fullerenes, carbon nanotubes, and carbon quantum dots can be used as semiconductors, photosensitizers, cocatalysts, and support materials. This review comprehensively explains how carbon-based composite materials function as photocatalytic semiconductors for hydrogen production, the water-splitting mechanism, and the chemistry of redox reactions. Also, how heteroatom doping, defects and surface functionalities, etc., can influence the efficiency of carbon photocatalysts in H2 production. The challenges faced in the PWS process and future prospects are briefly discussed.

GO/TiO2-Related Nanocomposites as Photocatalysts for Pollutant Removal in Wastewater Treatment

Water pollution has been a prevalent issue globally for some time. Some pollutants are released into the water system without treatment, making the water not suitable for consumption. This problem may lead to more grave problems in the future including the destruction of the ecosystem along with the organisms inhabiting it, and illness and diseases endangering human health. Conventional methods have been implemented to remove hazardous pollutants such as dyes, heavy metals, and oil but are incapable of doing so due to economic restraints and the inability to degrade the pollutants, leading to secondary pollution. Photocatalysis is a more recently applied concept and is proven to be able to completely remove and degrade pollutants into simpler organic compounds. Titanium dioxide (TiO₂) is a fine example of a photocatalyst owing to its cost-effectiveness and superb efficiency. However, issues such as the high recombination rate of photogenerated electrons along with positive holes while being only limited to UV irradiation need to be addressed. Carbonaceous materials such as graphene oxide (GO) can overcome such issues by reducing the recombination rate and providing a platform for adsorption accompanied by photocatalytic degradation of TiO₂. The history and development of the synthesis of GO will be discussed, followed by the methods used for GO/TiO₂ synthesis. The hybrid of GO/TiO₂ as a photocatalyst has received some attention in the application of wastewater treatment due to its efficiency and it being environmentally benign. This review paper thereby aims to identify the origins of different pollutants followed by the sickness they may potentially inflict. Recent findings, including that GO/TiO₂-related nanocomposites can remove pollutants from the water system, and on the photodegradation mechanism for pollutants including aromatic dyes, heavy metal and crude oil, will be briefly discussed in this review. Moreover, several crucial factors that affect the performance of photocatalysis in pollutant removal will be discussed as well. Therefore, this paper presents a critical review of recent achievements in the use of GO/TiO₂-related nanocomposites and photocatalysis for removing various pollutants in wastewater treatment.

Graphene-based TiO2 composites for photocatalysis & environmental remediation: synthesis and progress

Photoactive nanomaterials constitute an emerging field in nanotechnology, finding an extensive array of applications spanning diverse areas, including electronics and photovoltaic devices, solar fuel cells, wastewater treatment, etc. Titanium dioxide (TiO₂), in its thin-film form, has been exhaustively surveyed as potential photocatalysts for environmental remediation owing to its innocuousness, stability, and photocatalytic characteristics when subjected to ultraviolet (UV) irradiation. However, TiO₂ has some shortcomings associated with a large bandgap value of around 3.2 eV, making it less efficient in the visible spectral range. TiO₂ is often consolidated with various carbon nanomaterials to overcome this limitation and enhance its efficiency. Graphene, a 2-dimensional allotrope of carbon with a bandgap tuned between 0 and 0.25 eV, exhibits unique properties, making it an attractive candidate to augment the photoactivity of semiconductor (SC) oxides. Encapsulating graphene oxide onto TiO₂ nanospheres demonstrates intensified photocatalytic properties and exceptional recyclability for the degeneration of certain dyes, including Rhodamine B. This review encompasses various techniques to synthesize graphene-based TiO₂ photoactive composites, emphasizing graphene capsulized hollow titania nanospheres, nanofibers, core/shell, and reduced graphene oxide-TiO₂-based nanocomposites. It also consolidates the application of the aforestated nanocomposites for the disintegration of various synthetic dyes, proving efficacious for water decontamination and degradation of chemicals and pharmaceuticals. Furthermore, graphene-based TiO₂ nanocomposites used as lithium (Li)-ion batteries manifesting substantial electrochemical performance and solar fuel cells for energy production are discussed here.

Purification-analysis of urban rivers by combining graphene photocatalysis with sewage treatment improvement based on the MIKE11 model

This study takes the Nanfei River as an example, using a hydrodynamic and water quality model based on MIKE11 to predict the effect of graphene photocatalysis on urban rivers. The effect of water quality improvement in the Nanfei River was simulated under three different scenarios (treatment plant upgrade, use of graphene photocatalytic oxidation technology, and a combination of both), and the results showed that implementing a graphene photocatalytic network could significantly improve water quality. The improvement of sewage treatment plants can also improve the water quality to a certain extent, improving the sewage treatment plants alone is insufficient. The combination of graphene photocatalytic oxidation technology with methods to improve wastewater treatment plants produced the best improvement in water quality. The required water quality was achieved, as the total phosphorus content throughout the year was below the limit, and the ammonia nitrogen standard was met 95.89% of the time in the State-controlled section (Shikou section). Therefore, this study provides a new, feasible method for treating the water of polluted rivers.

An efficient CuO/rGO/TiO2 photocatalyst for the synthesis of benzopyranopyrimidine compounds under visible light irradiation

This study reports the synthesis of CuO/rGO/TiO2 in coupling reaction under visible light irradiation. Its photocatalytic performance was explored in a pseudo 4-component and a domino reaction for the synthesis of benzopyranopyrimidine compounds. It can be recovered and recycled for 5 runs.

Facile single-step synthesis of MXene@CNTs hybrid nanocomposite by CVD method to remove hazardous pollutants

In the present work, facile preparation of MXenes based nanocomposite (MXene-CNTs) through catalytic chemical vapor deposition (cCVD) was demonstrated. The novel design of two and one-dimensional (2D/1D) MXene-CNTs composites for an extraordinary photocatalytic process for removal of Rhodamine B (RhB) using efficient photocatalytic dye degradations was compared to the performance of pure MXene. The surface morphological behavior of MAX, MXene and MXene-CNTs rational design of surface microstructure CNTs anchored on 2D materials MXene nanosheets product was characterized employing scanning electron microscopy (SEM). As-prepared direct growth CNTs by employing CVD method were in the size ranges of 40-90 nm as revealed from SEM images. The crystallographic structures of etching and delaminations of MAX and MXene-CNTs were observed for CNTs diffracted peaks at 2θ = 25.11° in support of (002) plan. The major C-O and (CC) stretching were confirmed. Prepared MXene and MXene-CNTs samples photocatalytic performance was investigated through photocatalytic Rhodamine B (RhB) dye degradation. MXene-based CNTs hybrid nanocomposites photocatalysts activity were estimated. The as-prepared pure MXene-RhB and MXene-CNTs-RhB materials calculated efficiency were 60 % and 75 %, respectively. The CVD preparations of new MXene-CNTs synthesis yield high and explored good successive cycles for hazardous pollutants.

Influence of rGO and Preparation Method on the Physicochemical and Photocatalytic Properties of TiO2/Reduced Graphene Oxide Photocatalysts

In this study, a series of TiO2/rGO photocatalysts were obtained with a two-step procedure: a solvothermal method and calcination at 300–900 °C in an argon atmosphere. It was noted that the presence of rGO in photocatalysts had an important role in the changes in crystallite size and specific surface area. In TiO2/rGO samples, different surface functional groups, such as C−Cgraph, C−Caliph, C−OH, C=O, and CO(O), were found. It was observed that rGO modification suppressed the anatase-to-rutile phase transformation. The photocatalytic activity of the obtained nanomaterials was investigated through the decomposition of methylene blue under UV and artificial solar light irradiation. It was found that the adsorption degree played an important role in methylene blue decomposition. The experimental results revealed that TiO2/rGO samples exhibited superior removal efficiency after calcination for methylene blue compared toTiO2 without rGO, as well as a commercial photocatalyst KRONOClean 7000. It was noted that photocatalytic activity increased with the increase in the calcination temperature. The highest activity was observed for the sample calcined at 700 °C, which consisted of 76% anatase and 24% rutile. This study clearly demonstrated that TiO2/rGO samples calcined in argon can be used as efficient photocatalysts for the application of methylene blue decomposition.

Ag/GO/TiO2nanocomposites: the role of the interfacial charge transfer for application in photocatalysis

TiO₂semiconductor nanoparticles (NPs) in the anatase phase have presented limitations of application in photocatalysis, mainly due to the fast recombination of photoexcited electrons. The combination with other nanoparticles/nanostructures has been shown to be a promising solution for increasing photocatalytic efficiency. In this work, titanium dioxide (TiO₂) nanoparticles in different crystalline phases were prepared through a rapid microwave-assisted synthesis and modified by silver nanoparticles (Ag) and graphene oxide (GO). The samples were characterized by x-ray diffraction, transmission electron microscopy, energy dispersive x-ray spectroscopy, infrared spectroscopy and gas adsorption. Crystalline anatase NPs were obtained in basic conditions (pH = 8) while in acidic conditions (pH = 1), single-crystalline rutile NPs were formed. Different previous drying methods: oven and freeze-drying used led to a differentiation in crystallographic phases obtained. Anatase TiO₂and anatase-rutile mixture NPs calcined at 400 °C showed properties as high specific surface area, crystallinity and reduced electron-hole recombination which contributed to an enhanced photocatalytic activity, when compared to the Degussa P25 photoactivity. The effect of silver nanoparticles and GO addition to TiO₂nanopowder was evaluated for photocatalysis activity. An improvement in the methylene blue and rhodamine B dyes photodegradation was observed for both anatase and rutile TiO₂nanocomposites. We noted that anatase TiO₂nanoparticles degraded 53% of rhodamine B, and when functionalized with GO, the photodegradation increased to 69%. Comparatively, the addition of silver nanoparticles to anatase TiO₂increased the dye degradation to 97% in 180 min. Hence, we revel that in the TiO₂nanocomposites, silver nanoparticles showed better interfacial charge transfer than GO, contributing more effectively to the dye photodegradation process.

Effect of operational parameters on photocatalytic degradation of ethylparaben using rGO/TiO2 composite under UV radiation

The objective of this study was to analyze the influence of different operational variables (catalyst loading, initial EtP concentration, medium pH, the presence of anions and radical scavengers) on the performance of ethylparaben (EtP) photodegradation catalyzed with an rGO/TiO₂ composite. EtP was selected for study after analyzing the effect of paraben chain length on its catalytic photodegradation, finding that the photodegradation rate constant values of methyl-, ethyl-, and butyl-paraben are 0.050, 0.096, and 0.136 min^-1, respectively. This indicates that the photodegradation rate constant of parabens is higher with longer alkyl chain, which augments its oxidation capacity. The percentage removal of EtP at 40 min increases from 66.3 to 98.6 % when the composite dose rises from 100 to 700 mg/L; however, an additional increase in the composite dose to 1000 mg/L does not substantively improve the photodegradation rate or percentage EtP removal (98.9 %). A rise in the initial EtP concentration from 15 to 100 mg/L reduces the percentage of degradation from 100 to 76.4 %. The percentage EtP degradation is lower with higher solution pH. The presence of HCO₃^- or Cl^- anions in the medium reduces the degradation performance. Results obtained using positive hole and hydroxyl radical scavengers demonstrate that positive holes play an important role in EtP degradation. No degradation product evidences toxicity against the cultured human embryonic kidney cell line HEK-293.

Development of sonophotocatalytic process for degradation of acid orange 7 dye by using titanium dioxide nanoparticles/graphene oxide nanocomposite as a catalyst

In the present study, the sonophotocatalytic degradation of acid orange 7 (AO7) dye was evaluated. The catalyst used was the titanium dioxide nanoparticles/graphene oxide (TiO₂/GO) nanocomposite, which was synthesized using the Hummers and Hoffman's method and the liquid phase deposition method. TiO₂/GO nanocomposite was characterized through the analyses of transmission electron microscopy (TEM), X-ray diffraction (XRD), Energy Dispersive X-ray (EDX) spectroscopy, Raman spectroscopy, and Fourier transform infrared (FTIR) spectroscopy. In addition, properties of the surface area and pore size were determined by N₂ adsorption-desorption and the Barrett-Joyner-Halenda methods. After modification, the nanocomposite properties showed successful stabilization of TiO₂ on the graphene substrate and reduction of the recombinant carrier loads. By utilizing the proposed treatment, complete degradation of AO7 could be achieved under optimal operating parameters (pH = 5, initial concentration of AO7 dye = 50 mg/L, TiO₂/GO nanocomposite dose = 0.5 g/L, UV light intensity = 36 W, ultrasonic wave intensity = 35 kHz, and reaction time = 30 min). Scavenging experiments confirmed that OH and h⁺ radicals were the predominant species in the sonophotocatalytic degradation reactions of the AO7 dye. The stability study confirmed the excellent shelf life of the TiO₂/GO nanocomposite, with only a slight reduction in the degradation efficiency of the AO7 dye (<8.27%) detected, after six consecutive cycles of the sonophotocatalytic process. Studies related to the degradability of the AO7 dye and the biodegradability of the effluent from the process showed that the applied sonophotocatalytic system was able to remove the TOC concentration by 83% after a reaction time of 30 min. Moreover, the increase in the BOD₅/COD ratio was also a confirmation for the increase in biodegradability of the treated AO7 dye effluent. Finally, the toxicity test showed that the growth inhibition rate of Escherichia coli (E. coli), as a viability index, decreased to about 7.34% after a reaction time of 180 min. This result indicated the formation of compounds with low toxicity and molecular weight over the reaction time of the sonophotocatalytic process of AO7 dye.

Visible Light-Driven GO/TiO2-CA Nano-Photocatalytic Membranes: Assessment of Photocatalytic Response, Antifouling Character and Self-Cleaning Ability

Photocatalysis and membrane technology in a single unit is an ideal strategy for the development of wastewater treatment systems. In this work, novel GO (x wt%)/TiO2-CA hybrid membranes have been synthesized via a facile non-solvent induced phase inversion technique. The strategy aimed to address the following dilemmas: (1) Effective utilization of visible light and minimize e-/h+ recombination; (2) Enhanced separation capability and superior anti-fouling and self-cleaning ability. The experimental results reveal that the integration of nano-composite (GO/TiO2) boosts the membrane properties when compared to pristine CA and single photocatalyst employed membrane (GO-CA and TiO2-CA). The effect of GO content on the properties of the photocatalytic membrane has been determined by utilizing three different ratios of GO, viz. 0.5 wt%, 1 wt%, and 2 wt% designated as NC(1)-CA, NC(2)-CA, and NC(3)-CA, respectively. Amongst them, NC(3)-CA membrane showed state-of-the-art performance with an elevated photocatalytic response (four times higher than pristine CA membrane) toward methyl orange. Moreover, the water flux of NC(3)-CA membrane is 613 L/m2h, approximately three times higher than bare CA membrane (297 L/m2h), while keeping the MO rejection high (96.6%). Besides, fouling experiments presented the lowest total and fouling resistance ratios and a higher flux recovery ratio (91.78%) for the NC(3)-CA membrane, which endows the membrane with higher anti-fouling and self-cleaning properties. Thus, NC(3)-CA membrane outperforms the other as synthesized membranes in terms of separation efficiency, visible light photo-degradation of pollutant, anti-fouling and self-cleaning ability. Therefore, NC(3)-CA membrane is considered as the next generation membrane for exhibiting great potential for the wastewater treatment applications.

TiO2-Graphene Quantum Dots Nanocomposites for Photocatalysis in Energy and Biomedical Applications

The focus of current research in material science has shifted from “less efficient” single-component nanomaterials to the superior-performance, next-generation, multifunctional nanocomposites. TiO2 is a widely used benchmark photocatalyst with unique physicochemical properties. However, the large bandgap and massive recombination of photogenerated charge carriers limit its overall photocatalytic efficiency. When TiO2 nanoparticles are modified with graphene quantum dots (GQDs), some significant improvements can be achieved in terms of (i) broadening the light absorption wavelengths, (ii) design of active reaction sites, and (iii) control of the electron-hole (e−-h+) recombination. Accordingly, TiO2-GQDs nanocomposites exhibit promising multifunctionalities in a wide range of fields including, but not limited to, energy, biomedical aids, electronics, and flexible wearable sensors. This review presents some important aspects of TiO2-GQDs nanocomposites as photocatalysts in energy and biomedical applications. These include: (1) structural formulations and synthesis methods of TiO2-GQDs nanocomposites; (2) discourse about the mechanism behind the overall higher photoactivities of these nanocomposites; (3) various characterization techniques which can be used to judge the photocatalytic performance of these nanocomposites, and (4) the application of these nanocomposites in biomedical and energy conversion devices. Although some objectives have been achieved, new challenges still exist and hinder the widespread application of these nanocomposites. These challenges are briefly discussed in the Future Scope section of this review.

Photocatalytic performance improvement by utilizing GO_MWCNTs hybrid solution on sand/ZnO/TiO2-based photocatalysts to degrade methylene blue dye

In this work, sand/zinc oxide (ZnO)/titanium dioxide (TiO₂)-based photocatalysts were hybridized with graphene oxide (GO) and GO_multi-walled carbon nanotubes (MWCNTs) hybrid solution. The novel hybrid was then used in photocatalysis to degrade dye contamination. The nanocomposite photocatalyst was initially fabricated by growing ZnO nanorods (NRs) via sol-gel immersion followed by synthesizing TiO₂ NRs for different times (5 and 20 h) using a hydrothermal method on sand as a substrate. Prior to the hybridization, the initial GO was synthesized using electrochemical exfoliation and further mixed with 1 wt% MWCNTs to form GO_MWCNTs hybrid solution. The synthesized GO and GO_MWCNTs hybrid solution were then incorporated onto sand/ZnO/TiO₂ nanocomposite-based photocatalysts through immersion. Various sand/ZnO/TiO₂-based photocatalysts were then tested for methylene blue (MB) dye degradation within 3 days. On the basis of UV-Vis measurement, the highest MB degradation was achieved by using sand/ZnO NRs/TiO₂ NRs (5 h)/GO_MWCNTs (92.60%). The high surface area and high electrical conductivity of GO_MWCNTs prolonged the lifetime of electron/hole separation and thus enhanced the photocatalytic performance.

Reduction of aflatoxin B1 by magnetic graphene oxide/TiO2 nanocomposite and its effect on quality of corn oil

Magnetic graphene oxide/TiO₂(MGO/TiO₂) nanocomposite was synthesized for the reduction of aflatoxin B₁ (AFB₁) in corn oil. The photodegradation of synthesized nanocomposites on AFB₁ in corn oil under different treatment conditions and its effect on the quality of corn oil were investigated. The doping of magnetic GO effectively enhanced the photocatalytic activity of TiO₂ both under UV light and visible light. The reduction of AFB₁ in corn oil reached 96.4% after illumination for 120 min under UV-Vis light. Holes (h⁺) and the hydroxyl radicals (OH) were found to play important roles in the reduction of AFB₁, and three transformation products were confirmed by electrospray ionization mass spectrometry (ESI/MS) analysis. In addition, the quality of the treated corn oil was still acceptable after storage for 180 days. This study provides an effective, environmental-friendly and practical approach for reduction of AFB₁ in oil products.

Bi-Polymer Electrospun Nanofibers Embedding Ag3PO4/P25 Composite for Efficient Photocatalytic Degradation and Anti-Microbial Activity

Using a bi-polymer system comprising of transparent poly(methyl methacrylate) (PMMA) and poly(vinyl pyrrolidone) (PVP), a visible light active Ag3PO4/P25 composite was immobilized into the mats of polymeric electrospun nanofibers. After nanofibers synthesis, sacrificial PVP was removed, leaving behind rough surface nanofibers with easy access to Ag3PO4/P25 composite. The remarkable photocatalytic efficiency was attained using a PMMA and Ag3PO4/P25 weight ratio of 1:0.6. Methyl orange (MO) was used to visualize pollutant removal and exhibited stable removal kinetics up to five consecutive cycles under simulated daylight. Also, these polymeric nanofibers (NFs) revealed an important role in the destruction of microorganisms (E. coli), signifying their potential in water purification. A thin film fibrous mat was also used in a small bench scale plug flow reactor (PFR) for polishing of synthetic secondary effluent and the effects of inorganic salts were studied upon photocatalytic degradation in terms of total organic carbon (TOC) and turbidity removal. Lower flow rate (5 mL/h) resulted in maximum TOC and turbidity removal rates of 86% and 50%, respectively. Accordingly, effective Ag3PO4/P25 immobilization into an ideal support material and selectivity towards target pollutants could both enhance the efficiency of photocatalytic process under solar radiations without massive energy input.

Hydrothermal Synthesis of rGO-TiO2 Composites as High-Performance UV Photocatalysts for Ethylparaben Degradation

A series of reduced graphene oxide-TiO2 composites (rGO-TiO2) were prepared by hydrothermal treatment using graphite and titanium isopropoxide as raw materials. The structural, surface, electronic, and optical properties of the prepared composites were extensively characterized by N2 adsorption, FTIR, XRD, XPS, Raman spectroscopy, and DRS. GO was found to be effectively reduced and TiO2 to be in pure anatase phase in all composites obtained. Finally, experiments were performed to evaluate the effectiveness of these new materials as photocatalysts in the degradation of ethylparaben (EtP) by UV radiation. According to the band-gap energies obtained (ranging between 3.09 eV for 4% rGO-TiO2 to 2.55 eV for 30% rGO-TiO2), the rGO-TiO2 composites behave as semiconductor materials. The photocatalytic activity is highest with a rGO content of 7 wt% (7% rGO-TiO2), being higher than observed for pure TiO2 (Eg = 3.20 eV) and achieving 98.6% EtP degradation after only 40 min of treatment. However, the degradation yield decreases with higher percentages of rGO. Comparison with rGO-P25 composites showed that a better photocatalytic performance in EtP degradation is obtained with synthesized TiO2 (rGO-TiO2), probably due to the presence of the rutile phase (14.1 wt %) in commercial P25.

One-Pot Synthesis of Sulfur-Doped TiO2/Reduced Graphene Oxide Composite (S-TiO2/rGO) With Improved Photocatalytic Activity for the Removal of Diclofenac From Water

Sulfur-doped TiO2 (S-TiO2) composites with reduced graphene oxide (rGO), wt. % of rGO equal to 0.5%, 2.75%, and 5.0%, were prepared by a one-pot solvothermal procedure. The aim was to improve photocatalytic performance in comparison to TiO2 under simulated solar irradiation for the treatment of diclofenac (DCF) in aqueous medium. The obtained composites were characterized for physical-chemical properties using thermogravimetric analysis (TGA), X-ray diffractograms (XRD), Raman, scanning electron microscopy (SEM)/energy dispersive X-ray (EDX), Brauner Emmett Teller (BET), and photoluminescence (PL) analyses, indicating successful sulfur doping and inclusion of rGO. Sulfur doping and rGO have successfully led to a decrease in photogenerated charge recombination. However, both antagonistic and synergistic effects toward DCF treatment were observed, with the latter being brought forward by higher wt.% rGO. The composite with 5.0 wt.% rGO has shown the highest DCF conversion at pH 4 compared to that obtained by pristine TiO2, despite lower DCF adsorption during the initial dark period. The expected positive effects of both sulfur doping and rGO on charge recombination were found to be limited because of the subpar interphase contact with the composite and incomplete reduction of the GO precursor. Consequent unfavorable interactions between rGO and DCF negatively influenced the activity of the studied S-TiO2/rGO photocatalyst under simulated solar irradiation.

Visible-Light Active Titanium Dioxide Nanomaterials with Bactericidal Properties

This article provides an overview of current research into the development, synthesis, photocatalytic bacterial activity, biocompatibility and cytotoxic properties of various visible-light active titanium dioxide (TiO2) nanoparticles (NPs) and their nanocomposites. To achieve antibacterial inactivation under visible light, TiO2 NPs are doped with metal and non-metal elements, modified with carbonaceous nanomaterials, and coupled with other metal oxide semiconductors. Transition metals introduce a localized d-electron state just below the conduction band of TiO2 NPs, thereby narrowing the bandgap and causing a red shift of the optical absorption edge into the visible region. Silver nanoparticles of doped TiO2 NPs experience surface plasmon resonance under visible light excitation, leading to the injection of hot electrons into the conduction band of TiO2 NPs to generate reactive oxygen species (ROS) for bacterial killing. The modification of TiO2 NPs with carbon nanotubes and graphene sheets also achieve the efficient creation of ROS under visible light irradiation. Furthermore, titanium-based alloy implants in orthopedics with enhanced antibacterial activity and biocompatibility can be achieved by forming a surface layer of Ag-doped titania nanotubes. By incorporating TiO2 NPs and Cu-doped TiO2 NPs into chitosan or the textile matrix, the resulting polymer nanocomposites exhibit excellent antimicrobial properties that can have applications as fruit/food wrapping films, self-cleaning fabrics, medical scaffolds and wound dressings. Considering the possible use of visible-light active TiO2 nanomaterials for various applications, their toxicity impact on the environment and public health is also addressed.

Photocatalytic activity of exfoliated graphite-TiO2 nanoparticle composites

We investigate the photocatalytic performance of composites prepared in a one-step process by liquid-phase exfoliation of graphite in the presence of TiO₂ nanoparticles (NPs) at atmospheric pressure and in water, without heating or adding any surfactant, and starting from low-cost commercial reagents. These show enhanced photocatalytic activity, degrading up to 40% more pollutants with respect to the starting TiO₂-NPs, in the case of a model dye target, and up to 70% more pollutants in the case of nitrogen oxides. In order to understand the photo-physical mechanisms underlying this enhancement, we investigate the photo-generation of reactive species (trapped holes and electrons) by ultrafast transient absorption spectroscopy. We observe an electron transfer process from TiO₂ to the graphite flakes within the first picoseconds of the relaxation dynamics, which causes the decrease of the charge recombination rate, and increases the efficiency of the reactive species photo-production.