Foam Formation and Interaction with Porous Media

Т1 mapping of rat lungs in 19 F MRI using octafluorocyclobutane

PURPOSE

To demonstrate the feasibility of using octafluorocyclobutane (OFCB, c-C₄ F₈ ) for T₁ mapping of lungs in ¹⁹ F MRI.

METHODS

The study was performed at 7 T in three healthy rats and three rats with pulmonary hypertension. To increase the sensitivity of ¹⁹ F MRI, a bent-shaped RF coil with periodic metal strips structure was used. The double flip angle method was used to calculate normalized transmitting RF field (B_1n ⁺ ) maps and for correcting T₁ maps built with the variable flip angle (VFA) method. The ultrashort TE pulse sequence was applied for acquiring MR images throughout the study.

RESULTS

The dependencies of OFCB relaxation times on its partial pressure in mixtures with oxygen, air, helium, and argon were obtained. T₁ of OFCB linearly depended on its partial pressure with the slope of about 0.35 ms/kPa in the case of free diffusion. RF field inhomogeneity leads to distortion of T₁ maps built with the VFA method, and therefore to high standard deviation of T₁ in these maps. To improve the accuracy of the T₁ maps, the B_1n ⁺ maps were applied for VFA correction. This contributed to a 2-3-fold decrease in the SD of T₁ values in the corresponding maps compared with T₁ maps calculated without the correction. Three-dimensional T₁ maps were obtained, and the mean T₁ in healthy rat lungs was 35 ± 10 ms, and in rat lungs with pulmonary hypertension - 41 ± 9 ms.

CONCLUSION

OFCB has a spin-rotational relaxation mechanism and can be used for ¹⁹ F T₁ mapping of lungs. The calculated OFCB maps captured ventilation defects induced by edema.

Foam Quality of Foams Formed on Capillaries and Porous Media Systems

Foams are of great importance as a result of their expansive presence in everyday life—they are used in the food, cosmetic, and process industries, and in detergency, oil recovery, and firefighting. There is a little understanding of foam formation using soft porous media in terms of the quality of foam and foam formation. Interaction of foams with porous media has recently been investigated in a study by Arjmandi-Tash et al., where three different regimes of foam drainage in contact with porous media were observed. In this study, the amount of foam generated using porous media with surfactant solutions is investigated. The aim is to understand the quality of foam produced using porous media. The effect of capillary sizes and arrangement of porous in porous media has on the quality of foam is investigated. This is then followed by the use of soft porous media for foam formation to understand how the foam is generated on the surface of the porous media and the effect that different conditions (such as concentration) have on the quality of the foam. The quality of foam is a blanket term for bubble size, liquid volume fraction, and stability of the foam. The liquid volume fraction is calculated using a homemade dynamic foam analyser, which is used to obtain the distribution of liquid volume fraction along with the foam height. Soft porous media does not influence substantially the rate of decay of foam produced, however, it decreases the average diameter of the bubbles, whilst increasing the range of bubble sizes due to the wide range of pore sizes present in the soft porous media. The foam analyser showed the expected behaviour that, as the foam decays and becomes drier, the liquid volume fraction of the foam falls, and therefore the conductivity of foam also decreases, indicating the usefulness of the home-made device for future investigations.

Effect of synthetic surfactants on the environment and the potential for substitution by biosurfactants

The environmental impacts of the use of synthetic surfactants are discussed in this work such as their high levels of toxicity and low biodegradability. These materials destroy aquatic microbial populations, damage fish and other aquatic life, and reduce photochemical energy conversion efficiency of plants as well as adversely affecting waste-water treatment processes. With global usage of surfactants being over 15 million tonnes annually, and an estimated 60% of surfactant ending up in the aquatic environment, there is an urgent need for alternatives with lower adverse environmental effects; this review explores biosurfactants as potential alternatives. The sources and natural function of biosurfactants are presented, together with their advantages compared with their synthetic counterparts, including their low toxicity and biodegradability. Their comparable effectiveness as surfactants has been demonstrated by surface tension reduction, achieved at much lower critical micelle concentrations that those of synthetic surfactants. The limitations and challenges for the use of biosurfactants are discussed, particularly low production yields; such limitations must be addressed before wide range industrial use of biosurfactants can be achieved. Although there has been focus on achieving greater production yields, a remaining issue is the lack of research into the use of biosurfactants in a greater range of industrial and consumer applications to demonstrate their efficacy and identify candidate biosurfactants for production. This review highlights such research as deserving of further investigation, alongside the ongoing work to optimize the production process.