High-Temperature Tribological Performance of Hard Multilayer TiN-AlTiN/nACo-CrN/AlCrN-AlCrO-AlTiCrN Coating Deposited on WC-Co Substrate

Properties of Al2O3/Ti/Ni Composite Obtained by Slip Casting with Different Metal Phase Content

This work analyzed ceramic-metal composites from the Al₂O₃/Ti/Ni system produced by the slip casting method. As starting powders, nanometric Al₂O₃, Ni and Ti of submicron size were used. Three series of composites were obtained and tested with the same solid phase content (50% vol.) and different metallic phase content: 5, 10 and 15% vol. The influence of the metallic phase content on the basic properties of the proposed composites was examined by determining the phase composition of the produced samples using the XRD method, rheological measurements, and microstructural analysis (SEM/EDS). Additionally, before the sintering process, the slip stability was analyzed. A study of the fractography of samples after the sintering process was also carried out. It was shown that the appropriate manufacturing process allowed to obtain NiTi intermetallic phases in the structure of composites.

The Effectiveness of Diamond-like Carbon a-C:H:Si Coatings in Increasing the Cutting Capability of Radius End Mills When Machining Heat-Resistant Nickel Alloys

The main purpose of this paper was to study the efficiency of using diamond-like carbon (DLC) coatings based on a-C:H:Si with a pre-formed CrAlSiN sublayer to increase the cutting ability of ball end mills made of KFM-39 cemented carbide at a speed of 150–250 m/min in milling aircraft-grade Inconel 718, and to assess the DLC coating effect on the quality of the machined surface. DLC coating performance was quantified against uncoated carbide ball end mills and the proven TiN–AlN–TiAlN gradient multilayer coating at elevated temperatures measured by the natural thermocouple method. The temperature near the cutting edge is the factor determining the wear intensity in the tool contact surfaces in milling hard-to-machine nickel alloys to the greatest extent. Thermo-EMF (electromotive force) was recorded and converted into temperatures by calibration charts. The behavior of CrAlSiN–DLC and TiN–AlN–TiAlN coatings was compared with the results of high-temperature tribological tests on a ball-on-disc friction machine. For the CrAlSiN–DLC coating at cutting speeds of 150 and 200 m/min (<650 °C), the milling time until critical flank face wear (0.4 mm) was more than 67 and 50 min, respectively (1.4–1.5 times longer than an uncoated tool and about 1.3 times longer than the TiN–AlN–TiAlN coating). The CrAlSiN–DLC coating was characterized by a minimum adhesion amount.

High-Temperature Tribological Performance of Al2O3/a-C:H:Si Coating in Ambient Air

The study investigates thermal stability and high temperature tribological performance of a-C:H:Si diamond-like carbon (DLC) coating. A thin alumina layer was deposited on top of the a-C:H:Si coating to improve the tribological performance at high temperatures. The a-C:H:Si coating and alumina layer were prepared using plasma-activated chemical vapour deposition and atomic layer deposition, respectively. Raman and X-ray photoelectron spectroscopy were used to investigate the structures and chemical compositions of the specimens. The D and G Raman peaks due to sp2 bonding and the peaks corresponding to the trans-polyacetylene (t-Pa) and sp bonded chains were identified in the Raman spectra of the a-C:H:Si coating. Ball-on-disc sliding tests were carried out at room temperature and 400 °C using Si3N4 balls as counter bodies. The a-C:H:Si coating failed catastrophically in sliding tests at 400 °C; however, a repeatable and reproducible regime of sliding with a low coefficient of friction was observed for the Al2O3/a-C:H:Si coating at the same temperature. The presence of the alumina layer and high stress and temperature caused structural changes in the bulk a-C:H:Si and top layers located near the contact area, leading to the modification of the contact conditions, delivering of extra oxygen into the contact area, reduction of hydrogen effusion, and suppression of the atmospheric oxidation.

Influence of DLC Coatings Deposited by PECVD Technology on the Wear Resistance of Carbide End Mills and Surface Roughness of AlCuMg2 and 41Cr4 Workpieces

The primary purpose of this work was to study the effectiveness of using diamond-like coatings (DLC) to increase the wear resistance of carbide end mills and improve the surface quality of the processed part when milling aluminum alloy and low-carbon steel. The functional role of forming an adhesive sublayer based on (CrAlSi)N immediately before the application of the external DLC film by plasma-enhanced chemical vapor deposition (PECVD) technology in the composition of a multicomponent gas mixture containing tetramethylsilane was established in the article. The article shows the degree of influence of the adhesive sublayer on important physical, mechanical, and structural characteristics of DLCs (hardness, modulus of elasticity, index of plasticity, and others). A quantitative assessment of the effect of single-layer DLCs and double-layer (CrAlSi)N/DLCs on the wear rate of end mills during operation and the surface roughness of machined parts made of aluminum alloy AlCuMg2 and low-carbon steel 41Cr4 was performed.