LDH Post-Treatment of Flash PEO Coatings

Comparison of 2D and 3D Plasma Electrolytic Oxidation (PEO)-Based Coating Porosity Data Obtained by X-ray Tomography Rendering and a Classical Metallographic Approach

In this work, the porosity of plasma electrolytic oxidation (PEO)-based coatings on Al- and Mg-based substrates was studied by two imaging techniques-namely, SEM and computer microtomography. Two approaches for porosity determination were chosen; relatively simple and fast SEM surface and cross-sectional imaging was compared with X-ray micro computed tomography (microCT) rendering. Differences between 2D and 3D porosity were demonstrated and explained. A more compact PEO coating was found on the Al substrate, with a lower porosity compared to Mg substrates under the same processing parameters. Furthermore, huge pore clusters were detected with microCT. Overall, 2D surface porosity calculations did not show sufficient accuracy for them to become the recommended method for the exact evaluation of the porosity of PEO coatings; microCT is a more appropriate method for porosity evaluation compared to SEM imaging. Moreover, the advantage of 3D microCT images clearly lies in the detection of closed and open porosity, which are important for coating properties.

Effect of Pre-Anodized Film on Micro-Arc Oxidation Process of 6063 Aluminum Alloy

In the current investigation, micro-arc oxidation (MAO) ceramic coatings on aluminum are galvanostatically synthesized at various processing stages in an alkaline silicate system. The resultant coatings are systematically investigated in terms of the following respects: The working voltage and surface sparking evolution over the studied course of MAO are recorded by the signal acquisition system and the real-time imaging, respectively; the phase composition, the surface morphology, and the polished cross-section of the coatings are characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM) assisted with an energy-dispersive X-ray spectrometer (EDS), respectively. In particular, with the help of a low-rate increase in working voltage, the evolution of the sparks, the energy consumption, and the microstructure development of aluminum in alkaline silicate electrolyte by pre-anodizing are systematically investigated. The results show that the pre-anodized film can accelerate the evolution process of MAO spark and shorten the reaction process in the early stage of MAO reaction, reducing energy consumption and improving the corrosion resistance of the MAO coating. The γ-Al2O3 phase content after pre-anodized is significantly increased in MAO coatings. In particular, the thicker the pre-anodized film (beyond 8 μm) was broken down and fragmentation thinning in the early stage of the MAO process with the presence of micro discharges. This is due to the fact that the electron transition will be released by the emission of radiative recombination and reveals obvious galvanoluminescence (GL) behavior on the surface of the pre-anodized film. Further, based on the present MAO coating microstructure, a model of coating growth after pre-anodized that evolves over time is proposed.

Potential bioactive coating system for high-performance absorbable magnesium bone implants

Magnesium alloys are considered the most suitable absorbable metals for bone fracture fixation implants. The main challenge in absorbable magnesium alloys is their high corrosion/degradation rate that needs to be controlled. Various coatings have been applied to magnesium alloys to slow down their corrosion rates to match their corrosion rate to the regeneration rate of the bone fracture. In this review, a bioactive coating is proposed to slow down the corrosion rate of magnesium alloys and accelerate the bone fracture healing process. The main aim of the bioactive coatings is to enhance the direct attachment of living tissues and thereby facilitate osteoconduction. Hydroxyapatite, collagen type I, recombinant human bone morphogenetic proteins 2, simvastatin, zoledronate, and strontium are six bioactive agents that show high potential for developing a bioactive coating system for high-performance absorbable magnesium bone implants. In addition to coating, the substrate itself can be made bioactive by alloying magnesium with calcium, zinc, copper, and manganese that were found to promote bone regeneration.

•

Bioactive-coated magnesium implant could accelerate bone fracture healing time to match with magnesium degradation.

•

Hydroxyapatite, collagen type I, recombinant human bone morphogenetic proteins 2, simvastatin, zoledronate, and strontium are high potential bioactive coating materials.

•

The incorporation of Ca, Zn, Cu, Sr, and Mn in Mg base-metal could further enhance bone formation.

Emerging Layered Materials and Their Applications in the Corrosion Protection of Metals and Alloys

Metals and alloys are essential in modern society, and are used in our daily activities. However, they are prone to corrosion, with the conversion of the metal/alloy to its more thermodynamically-favored oxide/hydroxide phase. These undesirable corrosion reactions can lead to the failure of metallic components. Consequently, corrosion-protective technologies are now more important than ever, as it is essential to reduce the waste of valuable resources. In this review, we consider the role of emerging 2D materials and layered materials in the development of a corrosion protection strategy. In particular, we focus on the materials beyond graphene, and consider the role of transition metal dichalcogenides, such as MoS2, MXenes, layered double hydroxides, hexagonal boron nitride and graphitic carbon nitride in the formulation of effective and protective films and coatings. Following a short introduction to the synthesis and exfoliation of the layered materials, their role in corrosion protection is described and discussed. Finally, we discuss the future applications of these 2D materials in corrosion protection.

A Review on LDH-Smart Functionalization of Anodic Films of Mg Alloys

This review presents an overview of the recent developments in the synthesis of layered double hydroxide (LDH) on the anodized films of Mg alloys prepared by either conventional anodizing or plasma electrolytic oxidation (PEO) and the applications of the formed composite ceramics as smart chloride traps in corrosive environments. In this work, the main fabrication approaches including co-precipitation, in situ hydrothermal, and an anion exchange reaction are outlined. The unique structure of LDH nanocontainers enables them to intercalate several corrosion inhibitors and release them when required under the action of corrosion-relevant triggers. The influences of different variables, such as type of cations, the concentration of salts, pH, and temperature, immersion time during the formation of LDH/anodic film composites, on the electrochemical response are also highlighted. The correlation between the dissolution rate of PEO coating and the growth rate of the LDH film was discussed. The challenges and future development strategies of LDH/anodic films are also highlighted in terms of industrial applications of these materials.