Waste Glass Utilization in Cement-Based Materials for Sustainable Construction: A Review

Experimental investigation of mechanical properties and multi-objective optimization of electronic, glass, and ceramic waste-mixed concrete

The utilization of waste from various sources plays an important role in minimizing environmental pollution and civil construction costs. In this research, the mechanical properties of concrete were studied by mixing electronic waste (EW), glass powder (GW), and ceramic tile waste (CW). The effects of weight percentages of EW, GW, and CW are considered to investigate improvements in mechanical properties such as compressive strength (CS), split tensile strength (STS), and flexural strength (FS) of concrete. Taguchi analysis has been applied to predict the optimum composition of waste mixing percentages. The Multi-Objective Optimization Ratio Analysis (MOORA) techniques are applied to estimate the optimum composition of mixing wastes for maximizing the CS, STS, and FS of concrete. It was observed that 10 wt.% of EW, 15 wt.% of GW, and 30 wt.% of CW are predicted as the optimal mixing combinations to obtain a maximum compressive strength of 48.763 MPa, a split tensile strength of 4.178 MPa, and a flexural strength of 7.737 MPa, respectively. Finally, the predicted optimum waste-mixed weight percentages were used to examine the microstructure and various elements in the concrete using SEM and XRD analysis. When compared to conventional concrete, the optimum waste-mixed concrete has improved its compressive strength (38.453%), split tensile strength (41.149%), and flexural strength (36.215%).

Evaluating the effectiveness of waste glass powder for the compressive strength improvement of cement mortar using experimental and machine learning methods

This study utilized both experimental testing and machine learning (ML) strategies to assess the effectiveness of waste glass powder (WGP) on the compressive strength (CS) of cement mortar. The cement-to-sand ratio was kept 1:1 with a water-to-cement ratio of 0.25. The superplasticizer content was 4% by cement mass, and the proportion of silica fume was 15%, 20%, and 25% by cement mass in three different mixes. WGP was added to cement mortar at replacement contents from 0 to 15% for sand and cement with a 2.5% increment. Initially, using an experimental method, the CS of WGP-based cement mortar at the age of 28 days was calculated. The obtained data were then used to forecast the CS using ML techniques. For CS estimation, two ML approaches, namely decision tree and AdaBoost, were applied. The ML model's performance was assessed by calculating the coefficient of determination (R²), performing statistical tests and k-fold validation, and assessing the variance between the experimental and model outcomes. The use of WGP enhanced the CS of cement mortar, as noted from the experimental results. Maximum CS was attained by substituting 10% WGP for cement and 15% WGP for sand. The findings of the modeling techniques demonstrated that the decision tree had a reasonable level of accuracy, while the AdaBoost predicted the CS of WGP-based cement mortar with a higher level of accuracy. Utilizing ML approaches will benefit the construction industry by providing efficient and economic approaches for assessing the properties of materials.

Experimental and machine learning approaches to investigate the effect of waste glass powder on the flexural strength of cement mortar

Using solid waste in building materials is an efficient approach to achieving sustainability goals. Also, the application of modern methods like artificial intelligence is gaining attention. In this regard, the flexural strength (FS) of cementitious composites (CCs) incorporating waste glass powder (WGP) was evaluated via both experimental and machine learning (ML) methods. WGP was utilized to partially substitute cement and fine aggregate separately at replacement levels of 0%, 2.5%, 5%, 7.5%, 10%, 12.5%, and 15%. At first, the FS of WGP-based CCs was determined experimentally. The generated data, which included six inputs, was then used to run ML techniques to forecast the FS. For FS estimation, two ML approaches were used, including a support vector machine and a bagging regressor. The effectiveness of ML models was assessed by the coefficient of determination (R2), k-fold techniques, statistical tests, and examining the variation amongst experimental and forecasted FS. The use of WGP improved the FS of CCs, as determined by the experimental results. The highest FS was obtained when 10% and 15% WGP was utilized as a cement and fine aggregate replacement, respectively. The modeling approaches' results revealed that the support vector machine method had a fair level of accuracy, but the bagging regressor method had a greater level of accuracy in estimating the FS. Using ML strategies will benefit the building industry by expediting cost-effective and rapid solutions for analyzing material characteristics.

Evaluating the compressive strength of glass powder-based cement mortar subjected to the acidic environment using testing and modeling approaches

This study conducted experimental and machine learning (ML) modeling approaches to investigate the impact of using recycled glass powder in cement mortar in an acidic environment. Mortar samples were prepared by partially replacing cement and sand with glass powder at various percentages (from 0% to 15%, in 2.5% increments), which were immersed in a 5% sulphuric acid solution. Compressive strength (CS) tests were conducted before and after the acid attack for each mix. To create ML-based prediction models, such as bagging regressor and random forest, for the CS prediction following the acid attack, the dataset produced through testing methods was utilized. The test results indicated that the CS loss of the cement mortar might be reduced by utilizing glass powder. For maximum resistance to acidic conditions, the optimum proportion of glass powder was noted to be 10% as cement, which restricted the CS loss to 5.54%, and 15% as a sand replacement, which restricted the CS loss to 4.48%, compared to the same mix poured in plain water. The built ML models also agreed well with the test findings and could be utilized to calculate the CS of cementitious composites incorporating glass powder after the acid attack. On the basis of the R2 value (random forest: 0.97 and bagging regressor: 0.96), the variance between tests and forecasted results, and errors assessment, it was found that the performance of both the bagging regressor and random forest models was similarly accurate.

Evaluating the Strength and Impact of Raw Ingredients of Cement Mortar Incorporating Waste Glass Powder Using Machine Learning and SHapley Additive ExPlanations (SHAP) Methods

This research employed machine learning (ML) and SHapley Additive ExPlanations (SHAP) methods to assess the strength and impact of raw ingredients of cement mortar (CM) incorporated with waste glass powder (WGP). The data required for this study were generated using an experimental approach. Two ML methods were employed, i.e., gradient boosting and random forest, for compressive strength (CS) and flexural strength (FS) estimation. The performance of ML approaches was evaluated by comparing the coefficient of determination (R²), statistical checks, k-fold assessment, and analyzing the variation between experimental and estimated strength. The results of the ML-based modeling approaches revealed that the gradient boosting model had a good degree of precision, but the random forest model predicted the strength of the WGP-based CM with a greater degree of precision for CS and FS prediction. The SHAP analysis revealed that fine aggregate was a critical raw material, with a stronger negative link to the strength of the material, whereas WGP and cement had a greater positive effect on the strength of CM. Utilizing such approaches will benefit the building sector by supporting the progress of rapid and inexpensive approaches for identifying material attributes and the impact of raw ingredients.

Evaluation of Physical Characteristics and Sorption of Cement Mortars with Recycled Ceramic Aggregate

The subjects of this study were mortars with varying amounts of recycled ceramic aggregate (RCA). As part of the fine aggregate, the RCA volume share is 10%, 20%, 30%, 50% and 100%. First, fresh mixture parameters were evaluated, such as consistency and air content measurement by pressure method. Next, specimens were molded for compressive strength and flexural strength tests after 7, 28 and 56 days of curing. The thermo-humidity parameters of the composites, i.e., coefficient of capillary action and thermal conductivity coefficient were also investigated using nonstationary method. Sorption kinetics of the mortars at different moisture conditions at 20 °C were also evaluated. Sorption tests were carried out using two methods: TM and DVS. The sorption isotherms were plotted on the basis of equilibrium moisture content for the materials tested. The isotherms obtained by the two methods were evaluated. The results allowed us to draw conclusions on the physical and mechanical parameters of the composites with different amounts of RCA and to evaluate the ability to absorb moisture from the environment by these types of materials. A clear decrease in the compressive strength after 28 days of curing compared to the reference mortar was recorded after using 30% to 100% of RCA (approx. 26% to approx. 39%). Changes in flexural strength were significantly smaller, reaching no more than approx. 7.5%. It was shown that the amount of RCA translates into the ability to sorb moisture, which may affect the application of this type of composites. The amount of RCA translates also into the thermal conductivity coefficient, which decreased with increasing amount of RCA.