Bonding of Core Build-Up Composites with Glass Fiber-Reinforced Posts

Influence of Laser Irradiation Settings, during Diode-Assisted Endodontics, on the Intraradicular Adhesion of Self-Etch and Self-Curing Luting Cement during Restoration-An Ex Vivo Study

Background: Diode-assisted endodontics is nowadays utilized for pulp space disinfection, but little is known on the bonding potential of this lased root dentin when the tooth is restored with an intracanal polymer post. Objectives: to investigate the influence of diode laser irradiation settings, in laser-assisted endodontics, on the intraradicular bonding of composite materials. Methods: Sixteen two-rooted, maxillary first premolars were collected, prepared up to F4 (Protaper Universal. Dentsply-Maillefer, Ballaigues, Switzerland), and randomly assigned in two groups: group A (chopped mode or short pulse), diode irradiated according to protocol, pulse 25 ms, power 2.5 W, and group B (microchopped mode or ultrashort pulse), pulse 25 μs, peak power 12 W (both groups GentleRay. KaVo Dental, Biberach an der Riss, Germany). Buccal canals were irradiated, palatal ones served as controls. Canals were then obturated, post space was created in all canals, and quartz-fiber posts (ICE light Danville. Danville Materials, San Ramon, CA, USA) were cemented by self-etch self-curing cement (Max Cem Elite. Kerr, West Collins Orange, CA, USA) (Max Cem Elite. Kerr, Brea, CA, USA). A week later, teeth were sectioned horizontally in 1 mm increments. Push-out test was conducted in a Zwick testing machine (Zwick Roell, Ulm, Germany) at 1 mm/min speed, and the force required to dislodge the post from each specimen (F-max) was recorded. Weibull regression models were applied for statistical analyses. Results: Differences in F-max by group (control vs. chopped mode vs. microchopped mode) and height (meaning the apical-to-coronal position of each specimen along the root) were statistically significant (p < 0.05 in all cases). Conclusions: Short pulses (or chopped mode) had a profound positive effect on the quality of intraradicular bonding, while Ultrashort pulses (or microchopped mode) affected it negatively. In addition, apically positioned bonding proved weaker compared with more coronally located specimens.

Glass Fiber Reinforced Composite Orthodontic Retainer: In Vitro Effect of Tooth Brushing on the Surface Wear and Mechanical Properties

Fiber reinforced composites (FRCs) are metal free materials that have many applications in dentistry. In clinical orthodontics, they are used as retainers after active treatment in order to avoid relapse. However, although the modulus of the elasticity of FRCs is low, the rigidity of the material in the form of a relatively thick retainer with a surface cover of a flowable resin composite is known to have higher structural rigidity than stainless steel splints. The aim of the present study is to measure load and bending stress of stainless steel wires, as well as flowable resin composite covered and spot‑bonded FRC retainer materials after tooth brushing. These materials were tested with a three point bending test for three different conditions: no brushing, 26 min of brushing, and 60 min of brushing. SEM images were taken before and after different times of tooth brushing. Results showed that stainless steel was not significantly affected by tooth brushing. On the other hand, a significant reduction of values at maximum load at fracture was reported for both FRC groups, and uncovered FRCs were most affected. Concerning maximum bending stress, no significant reduction by pretreatment conditions was reported for the materials tested. SEM images showed no evident wear for stainless steel. Flowable resin composite covered FRCs showed some signs of composite wear, whereas spot‑bonded FRCs, i.e., without the surface cover of a flowable resin composite, showed signs of wear on the FRC and exposed glass fibers from the FRC's polymer matrix. Because of the significant changes of the reduction of maximum load values and the wear for spot‑bonded FRCs, this technique needs further in vitro and in vivo tests before it can be performed routinely in clinical practice.