Deep Learning Applications with Practical Measured Results in Electronics Industries

A Novel System to Increase Yield of Manufacturing Test of an RF Transceiver through Application of Machine Learning

Electronic manufacturing and design companies maintain test sites for a range of products. These products are designed according to the end-user requirements. The end user requirement, then, determines which of the proof of design and manufacturing tests are needed. Test sites are designed to carry out two things, i.e., proof of design and manufacturing tests. The team responsible for designing test sites considers several parameters like deployment cost, test time, test coverage, etc. In this study, an automated test site using a supervised machine learning algorithm for testing an ultra-high frequency (UHF) transceiver is presented. The test site is designed in three steps. Firstly, an initial manual test site is designed. Secondly, the manual design is upgraded into a fully automated test site. And finally supervised machine learning is applied to the automated design to further enhance the capability. The manual test site setup is required to streamline the test sequence and validate the control and measurements taken from the test equipment and unit under test (UUT) performance. The manual test results showed a high test time, and some inconsistencies were observed when the test operator was required to change component values to tune the UUT. There was also a sudden increase in the UUT quantities and so, to cater for this, the test site is upgraded to an automated test site while the issue of inconsistencies is resolved through the application of machine learning. The automated test site significantly reduced test time per UUT. To support the test operator in selecting the correct component value the first time, a supervised machine learning algorithm is applied. The results show an overall improvement in terms of reduced test time, increased consistency, and improved quality through automation and machine learning.

A Universal Machine-Learning-Based Automated Testing System for Consumer Electronic Products

Consumer electronic manufacturing (CEM) companies face a constant challenge to maintain quality standards during frequent product launches. A manufacturing test verifies product functionality and identifies manufacturing defects. Failure to complete testing can even result in product recalls. In this research, a universal automated testing system has been proposed for CEM companies to streamline their test process in reduced test cost and time. A universal hardware interface is designed for connecting commercial off-the-shelf (COTS) test equipment and unit under test (UUT). A software application, based on machine learning, is developed in LabVIEW. The test site data for around 100 test sites have been collected. The application automatically selects COTS test equipment drivers and interfaces on UUT and test measurements for test sites through a universal hardware interface. Further, it collects real-time test measurement data, performs analysis, generates reports and key performance indicators (KPIs), and provides recommendations using machine learning. It also maintains a database for historical data to improve manufacturing processes. The proposed system can be deployed standalone as well as a replacement for the test department module of enterprise resource planning (ERP) systems providing direct access to test site hardware. Finally, the system is validated through an experimental setup in a CEM company.

An Artificial Neural Network Approach and a Data Augmentation Algorithm to Systematize the Diagnosis of Deep-Vein Thrombosis by Using Wells’ Criteria

The use of a back-propagation artificial neural network (ANN) to systematize the reliability of a Deep Vein Thrombosis (DVT) diagnostic by using Wells’ criteria is introduced herein. In this paper, a new ANN model is proposed to improve the Accuracy when dealing with a highly unbalanced dataset. To create the training dataset, a new data augmentation algorithm based on statistical data known as the prevalence of DVT of real cases reported in literature and from the public hospital is proposed. The above is used to generate one dataset of 10,000 synthetic cases. Each synthetic case has nine risk factors according to Wells’ criteria and also the use of two additional factors, such as gender and age, is proposed. According to interviews with medical specialists, a training scheme was established. In addition, a new algorithm is presented to improve the Accuracy and Sensitivity/Recall. According to the proposed algorithm, two thresholds of decision were found, the first one is 0.484, which is to improve Accuracy. The other one is 0.138 to improve Sensitivity/Recall. The Accuracy achieved is 90.99%, which is greater than that obtained with other related machine learning methods. The proposed ANN model was validated performing the k-fold cross validation technique using a dataset with 10,000 synthetic cases. The test was performed by using 59 real cases obtained from a regional hospital, achieving an Accuracy of 98.30%.