Electro-Microbiology as a Promising Approach Towards Renewable Energy and Environmental Sustainability

Electroactive properties of EABs in response to long-term exposure to polystyrene microplastics/nanoplastics and the underlying adaptive mechanisms

Given widespread presence of polystyrene (PS) microplastics/nanoplastics (MPs/NPs), the electroactive responses and adaptation mechanisms of electroactive biofilms (EABs) exposed long-term to PS-containing aquatic environments remain unclear. Therefore, this study investigated the impacts of PS MPs/NPs on electroactivity of EABs. Results found that EABs exhibited delayed formation upon initially exposure but displayed an increased maximum current density (Imax) after subsequent exposure for up to 55 days. Notably, EABs exposure to NH2PS NPs (EAB-NH2PSNPs) demonstrated a 50% higher Imax than the control, along with a 17.84% increase in viability and a 58.10% increase in biomass. The cytochrome c (c-Cyts) content in EAB-NH2PSNPs rose by 178.35%, benefiting the extracellular electron transfer (EET) of EABs. Moreover, bacterial community assembly indicated the relative abundance of electroactive bacteria increased to 87.56% in EAB-NH2PSNPs. The adaptability mechanisms of EABs under prolonged exposure to PS MPs/NPs predominantly operate by adjusting viability, EET, and bacterial community assembly, which were further confirmed a positive correlation with Imax through structural equation model. These findings provide deeper insights into long-term effects and mechanisms of MPs/NPs on the electroactive properties of EABs and even functional microorganisms in aquatic ecosystems.

Investigation of Corrosion Inhibition of Mild Steel in 0.5 M H2SO4 with Lachancea fermentati Inhibitor Extracted from Rotten Grapefruits (Vitis vinifera): Adsorption, Thermodynamic, Electrochemical, and Quantum Chemical Studies

Corrosion inhibition of mild steel (MS) was studied using Lachancea fermentati isolate in 0.5 M H2SO4, which was isolated from rotten grapes (Vitis vinifera) via biofilm formation. Biofilm over the MS surface was asserted by employing FT-IR and FE-SEM with EDXS, electrochemical impedance spectroscopy (EIS), AFM, and DFT-ESP techniques. The weight loss experiments and temperature studies supported the physical adsorption behavior of the corrosion inhibitors. The maximum inhibition efficiency (IE) value (90%) was observed at 293 K for 9 × 106 cfu/mL of Lachancea fermentati isolate. The adsorption of Lachancea fermentati isolate on the surface of MS confirms Langmuir's adsorption isotherm model, and the -ΔG values indicate the spontaneous adsorption of inhibitor over the MS surface. Electrochemical studies, such as potentiodynamic polarization (PDP) and EIS were carried out to investigate the charge transfer (CT) reaction of the Lachancea fermentati isolate. Tafel polarization curves reveal that the Lachancea fermentati isolate acts as a mixed type of inhibitor. The Nyquist plots (EIS) indicate the increase in charge transfer resistance (Rct) and decrease of double-layer capacitance (Cdl) values when increasing the concentration of Lachancea fermentati isolate. The spectral studies, such as UV-vis and FT-IR, confirm the formation of a complex between MS and the Lachancea fermentati isolate inhibitor. The formation of biofilm on the MS surface was confirmed by FE-SEM, EDXS, and XPS analysis. The proposed bioinhibitor shows great potential for the corrosion inhibition of mild steel in acid media.

Biofilm modifiers: The disparity in paradigm of oral biofilm ecosystem

A biofilm is a population of sessile microorganisms that has a distinct organized structure and characteristics like channels and projections. Good oral hygiene and reduction in the prevalence of periodontal diseases arise from minimal biofilm accumulation in the mouth, however, studies focusing on modifying the ecology of oral biofilms have not yet been consistently effective. The self-produced matrix of extracellular polymeric substances and greater antibiotic resistance make it difficult to target and eliminate biofilm infections, which lead to serious clinical consequences that are often lethal. Therefore, a better understanding is required to target and modify the ecology of biofilms in order to eradicate the infection, not only in instances of oral disorders but also in terms of nosocomial infections. The review focuses on several biofilm ecology modifiers to prevent biofilm infections, as well as the involvement of biofilm in antibiotic resistance, implants or in-dwelling device contamination, dental caries, and other periodontal disorders. It also discusses recent advances in nanotechnology that may lead to novel strategies for preventing and treating infections caused by biofilms as well as a novel outlook to infection control.

In Situ Enhanced Yields of Microbial Nanowires: The Key Role of Environmental Stress

The conductive microbial nanowires of Geobacter sulfurreducens serve as a model for long-range extracellular electron transfer (EET), which is considered a revolutionary "green" nanomaterial in the fields of bioelectronics, renewable energy, and bioremediation. However, there is no efficient pathway to induce microorganisms to express a large amount of microbial nanowires. Here, several strategies have been used to successfully induce the expression of microbial nanowires. Microbial nanowire expression was closely related to the concentration of electron acceptors. The microbial nanowire was around 17.02 μm in length, more than 3 times compared to its own length. The graphite electrode was used as an alternative electron acceptor by G. sulfurreducens, which obtained a fast start-up time of 44 h in microbial fuel cells (MFCs). Meanwhile, Fe(III) citrate-coated sugarcane carbon and biochar were prepared to test the applicability of these strategies in the actual microbial community. The unsatisfied EET efficiency between c-type cytochrome and extracellular insoluble electron receptors promoted the expression of microbial nanowires. Hence, microbial nanowires were proposed to be an effective survival strategy for G. sulfurreducens to cope with various environmental stresses. Based on this top-down strategy of artificially constructed microbial environmental stress, this study is of great significance for exploring more efficient methods to induce microbial nanowires expression.

Advancements in Bioelectricity Generation Through Nanomaterial-Modified Anode Electrodes in Microbial Fuel Cells

The use of nanotechnology in bioelectrochemical systems to recover bioelectricity and metals from waste appears to be a potentially appealing alternative to existing established procedures. This trend exactly characterizes the current renewable energy production technology. Hence, this review focuses on the improvement of the anode electrode by using different functional metal oxide-conducting polymer nanocomposites to enhance microbial fuel cell (MFC) performance. Enhancement of interfacial bioelectrocatalysis between electroactive microorganisms and hierarchical porous nanocomposite materials could enhance cost-effective bioanode materials with superior bioelectrocatalytic activity for MFCs. In this review, improvement in efficiency of MFCs by using iron oxide- and manganese oxide-based polypyrrole hybrid composites as model anode modifiers was discussed. The review also extended to discussing and covering the principles, components, power density, current density, and removal efficiencies of biofuel cell systems. In addition, this research review demonstrates the application of MFCs for renewable energy generation, wastewater treatment, and metal recovery. This is due to having their own unique working principle under mild conditions and using renewable biodegradable organic matter as a direct fuel source.

Synchronous Cr(VI) Remediation and Energy Production Using Microbial Fuel Cell from a Subsurface Environment: A Review

Applying microbial fuel cell (MFC) technology for eco-remediation of Cr(VI) pollution from a subsurface environment has great scientific value and practical significance due to its promising advantages of pollutant remediation and renewable energy generation. The aim of the current review is to summarize the migration characteristics of Cr(VI) in a subsurface soil/water environment and investigate the factors affecting the MFC performance for synchronous Cr(VI) remediation and power generation, and sequentially highlight diverse challenges of MFC technology for in situ remediation of subsurface groundwater and soils. The critical review put forward that Cr(VI) removal efficiency and energy production of MFC can be improved by enhancing the adjustability of cathode pH, setting potential, modifying electrode, and incorporating other technologies into MFC. It was recommended that designing typical large-scale, long-term continuous flow MFC systems, adding electron shuttle media or constructing artificial electron according to actual groundwater/soil and Cr(VI) pollution characteristics, site geology, and the hydrogeology condition (hydrochemical conditions, colloid type, and medium) are essential to overcome the limitations of the small size of the laboratory experiments and improve the application of technology to in situ Cr(VI) remediation. This review provided reference and ideas for future research of MFC-mediated onsite Cr(VI) remediation.

Valorisation of CO2 into Value-Added Products via Microbial Electrosynthesis (MES) and Electro-Fermentation Technology

Microbial electrocatalysis reckons on microbes as catalysts for reactions occurring at electrodes. Microbial fuel cells and microbial electrolysis cells are well-known in this context; both prefer the oxidation of organic and inorganic matter for producing electricity. Notably, the synthesis of high energy-density chemicals (fuels) or their precursors by microorganisms using bio-cathode to yield electrical energy is called Microbial Electrosynthesis (MES), giving an exceptionally appealing novel way for producing beneficial products from electricity and wastewater. This review accentuates the concept, importance and opportunities of MES, as an emerging discipline at the nexus of microbiology and electrochemistry. Production of organic compounds from MES is considered as an effective technique for the generation of various beneficial reduced end-products (like acetate and butyrate) as well as in reducing the load of CO2 from the atmosphere to mitigate the harmful effect of greenhouse gases in global warming. Although MES is still an emerging technology, this method is not thoroughly known. The authors have focused on MES, as it is the next transformative, viable alternative technology to decrease the repercussions of surplus carbon dioxide in the environment along with conserving energy.

Advances in technological control of greenhouse gas emissions from wastewater in the context of circular economy

This review paper aims to identify the main sources of carbon dioxide (CO₂) emissions from wastewater treatment plants (WWTPs) and highlights the technologies developed for CO₂ capture in this milieu. CO₂ is emitted in all the operational units of conventional WWTPs and even after the disposal of treated effluents and sludges. CO₂ emissions from wastewater can be captured or mitigated by several technologies such as the production of biochar from sludge, the application of constructed wetlands (CWs), the treatment of wastewater in microbial electrochemical processes (microbial electrosynthesis, MES; microbial electrolytic carbon capture, MECC; in microbial carbon capture, MCC), and via microalgal cultivation. Sludge-to-biochar and CW systems showed a high cost-effectiveness in the capture of CO₂, while MES, MECC, MCC technologies, and microalgal cultivation offered efficient capture of CO₂ with associate production of value-added by-products. At the state-of-the-art, these technologies, utilized for carbon capture and utilization from wastewater, require more research for further configuration, development and cost-effectiveness. Moreover, the integration of these technologies has a potential internal rate of return (IRR) that could equate the operation or provide additional revenue to wastewater management. In the context of circular economy, these carbon capture technologies will pave the way for new sustainable concepts of WWTPs, as an essential element for the mitigation of climate change fostering the transition to a decarbonised economy.

Bioelectrochemical systems for environmental remediation of estrogens: A review and way forward

Globally estrogenic pollutants are a cause of concern in wastewaters and water bodies because of their high endocrine disrupting activity leading to extremely negative impacts on humans and other organisms even at very low environmental concentrations. Bioremediation of estrogens has been studied extensively and one technology that has emerged with its promising capabilities is Bioelectrochemical Systems (BESs). Several studies in the past have investigated BESs applications for treatment of wastewaters containing toxic recalcitrant pollutants with a primary focus on improvement of performance of these systems for their deployment in real field applications. But the information is scattered and further the improvements are difficult to achieve for standalone BESs. This review critically examines the various existing treatment technologies for the effective estrogen degradation. The major focus of this paper is on the technological advancements for scaling up of these BESs for the real field applications along with their integration with the existing and conventional wastewater treatment systems. A detailed discussion on few selected microbial species having the unusual properties of heterotrophic nitrification and extraordinary stress response ability to toxic compounds and their degradation has been highlighted. Based on the in-depth study and analysis of BESs, microbes and possible benefits of various treatment methods for estrogen removal, we have proposed a sustainable Hybrid BES-centered treatment system for this purpose as a choice for wastewater treatment. We have also identified three pipeline tasks that reflect the vital parts of the life cycle of drugs and integrated treatment unit, as a way forward to foster bioeconomy along with an approach for sustainable wastewater treatment.

High throughput techniques for the rapid identification of electroactive microorganisms

Electroactive microorganisms (EAM), capable of executing extracellular electron transfer (EET) in/out of a cell, are employed in microbial electrochemical technologies (MET) and bioelectronics for harnessing electricity from wastewater, bioremediation and as biosensors. Thus, investigation on EAM is becoming a topic of interest for multidisciplinary areas, such as environmental science, energy and health sectors. Though, EAM are widespread in three domains of life, nevertheless, only a few hundred EAM have been identified so far and hence, the rapid identification of EAM is imperative. In this review, the techniques that are developed for the direct identification of EAM, such as azo dye and WO₃ based techniques, dielectrophoresis, potentiostatic/galvanometric techniques, and other indirect methods, such as spectroscopy and molecular biology techniques, are highlighted with a special focus on time required for the detection of these EAM. The bottlenecks for identifying EAM and the knowledge gaps based on the present investigations are also discussed. Thus, this review is intended to encourage researchers for devolving high-throughput techniques for identifying EAM with more accuracy, while consuming less time.

MXene-coated biochar as potential biocathode for improved microbial electrosynthesis system

Microbial electrosynthesis (MES) holds tremendous large scale energy storage potential. By promoting the bioconversion of carbon dioxide (bicarbonate) into useful chemical commodities, this technique utilizes renewable energy and reduces carbon footprint. However, expensive electrode materials, low current densities, and multiple electrosynthesis products are major challenges to this field. To this end, this study examines a multilayered and conductive MXene structure that was coated on a cost-effective biochar substrate and tested as a MES cathode. These results show this coating yielded improved electrical conductivity, increased charge transfer efficiency, and selective microbial enrichment characteristics, resulting in a 2.3-fold increase in cathodic current production in comparison to the uncoated biochar. Moreover, an increase in active sites improved mass transfer and microbial growth, producing 1.7-fold increase in butyrate in comparison to the uncoated control. Considering that electrode attached microbial communities play a major role in final products, microbial community analyses was completed, suggesting that selective microbial enrichment was promoted as Firmicutes (66%), Proteobacteria (13%), and Bacteroidetes (12%) (i.e., exoelectrogenic and butyrate producing phyla) which were dominant in the MXene-coated biochar biofilm. These results show that biochar modification is an effective technique for achieving selective products through MES.

Electrotrophy of biocathodes regulates microbial-electro-catalyzation of CO2 to fatty acids in single chambered system

Microbial electrochemical conversion of CO₂ to value-added products needs effectual biocathodes. In this study, three different working electrodes (biocathode) namely carbon cloth (CC, MES1), stainless steel mesh (SS, MES2) and hybrid electrode (CC + SS, MES3) were evaluated in membrane-less single-chambered Microbial electrosynthesis systems (MESs). Performance of MES was assessed by total volatile fatty acids (VFA) productivity and, reductive current generations upon continuous poised potential (-0.4 V vs. Ag/AgCl (3.5 M KCl)). MES3 showed higher VFA synthesis (CC + SS; 1.4 g VFA/L), followed by MES1 (CC; 1.1 g VFA/L) and MES2 (SS; 0.8 g VFA/L) with corresponding reductive current generation of -1.13 mA, -2.74 mA and -0.39 mA. Electro-kinetics revealed the biocathode efficacy towards enhanced electrotrophy with confined electron losses by regulating electron flux in the system. The study infers the potential of hybrid electrode as an efficient biocathode for the reduction of CO₂ to VFA synthesis.

Turning harmful algal biomass to electricity by microbial fuel cell: A sustainable approach for waste management

Effective utilization of harmful algal biomass from eutrophic lakes is required for sustainable waste management and circular bioeconomy. In this study, Microcystis aeruginosa derived biomass served as an electron donor in the microbial fuel cell (MFC) for waste treatment and electricity generation. Bioelectrochemical performance of MFC fed with microalgae (MFC-Algae) was compared with MFC fed with a commercial substrate (MFC-Acetate). Complete removal of microcystin-LR (MC-LR) and high chemical oxygen demand (COD) removal efficiency (67.5 ± 1%) in MFC-Algae showed that harmful algal biomass could be converted into bioelectricity. Polarization curves revealed that MFC-Algae delivered the maximum power density (83 mW/m²) and current density (672 mA/m²), which was 43% and 45% higher than that of MFC-Acetate respectively. Improved electrochemical performance and substantial coulombic efficiency (7.6%) also verified the potential use of harmful algal biomass as an alternate MFC substrate. Diverse microbial community profiles showed the substrate-dependent electrogenic activities in each MFC. Biodegradation pathway of MC-LR by anodic microbes was also explored in detail. Briefly, a sustainable approach for on-site waste management of harmful algal biomass was presented, which was deprived of transportation and special pretreatments. It is anticipated that current findings will help to pave the way for practical applications of MFC technology.

Synthesis of Biogenic Palladium Nanoparticles Using Citrobacter sp. for Application as Anode Electrocatalyst in a Microbial Fuel Cell

Palladium (Pd) is a cheap and effective electrocatalyst that is capable of replacing platinum (Pt) in various applications. However, the problem in using chemically synthesized Pd nanoparticles (PdNPs) is that they are mostly fabricated using toxic chemicals under severe conditions. In this study, we present a more environmentally-friendly process in fabricating biogenic Pd nanoparticles (Bio-PdNPs) using Citrobacter sp. isolated from wastewater sludge. Successful fabrication of Bio-PdNPs was achieved under anaerobic conditions at pH six and a temperature of 30 °C using sodium formate (HCOONa) as an electron donor. Citrobacter sp. showed biosorption capabilities with no enzymatic contribution to Pd(II) uptake during absence of HCOONa in both live and dead cells. Citrobacter sp. live cells also displayed high enzymatic contribution to the removal of Pd(II) by biological reduction. This was confirmed by Scanning Electron Microscope (SEM), Electron Dispersive Spectroscopy (EDS), and X-ray Diffraction (XRD) characterization, which revealed the presence Bio-PdNPs deposited on the bacterial cells. The bio-PdNPs successfully enhanced the anode performance of the Microbial Fuel Cell (MFC). The MFC with the highest Bio-PdNPs loading (4 mg Bio-PdNP/cm2) achieved a maximum power density of 539.3 mW/m3 (4.01 mW/m2) and peak voltage of 328.4 mV.

Facile synthesis of N/B-double-doped Mn2O3 and WO3 nanoparticles for dye degradation under visible light

In the present work, nitrogen-doped and nitrogen-boron-double-doped manganese oxide (Mn₂O₃) and tungsten oxide (WO₃) nanoparticles were synthesized using precipitation-hydrothermal method for methylene blue degradation under visible light. Materials were characterized using X-ray diffraction (XRD) analysis, Scanning electron microscopy, Energy dispersive X-ray spectroscopy and UV-vis spectroscopy. Results showed that N and B were successfully incorporated into the crystal lattices of Mn₂O₃ and WO₃. XRD showed that WO₃ was crystallized in the form of a monoclinic lattice, while cubic Mn₂O₃ was produced in the cubic form. The crystallite size was found to be decreased due to the substitution of N and B elements which reveals their roles to accelerate the crystal nucleation rate resulting in the decreased size. On the other hand, single and double doping has successfully narrowed the band gaps of the as-synthesised metal oxide photocatalysts resulting in better absorption in the visible light. Band gaps obtained were as follows: 3.02, 2.50, 1.73 and 1.77 eV for N-WO₃ N/B-WO₃, N-Mn₂O₃ and N/B-Mn₂O₃ respectively. Photocatalytic experiments showed that all as-synthesised materials exhibited a photocatalytic efficiency under visible light ≥420 nm. The degradation efficiency of methylene blue (MB) was in the following order: N-B-co-doped metal oxides > N-doped metal oxides > metal oxides. The presence of scavenger molecules such as isopropanol, EDTA-2Na and benzoquinone inhibited MB degradation. Finally, the results showed that these materials can be reused several times without a notable decrease in efficiency.

Beyond Risk: Bacterial Biofilms and Their Regulating Approaches

Bacterial biofilms are complex surface attached communities of bacteria held together by self-produced polymer matrixs mainly composed of polysaccharides, secreted proteins, and extracellular DNAs. Bacterial biofilm formation is a complex process and can be described in five main phases: (i) reversible attachment phase, where bacteria non-specifically attach to surfaces; (ii) irreversible attachment phase, which involves interaction between bacterial cells and a surface using bacterial adhesins such as fimbriae and lipopolysaccharide (LPS); (iii) production of extracellular polymeric substances (EPS) by the resident bacterial cells; (iv) biofilm maturation phase, in which bacterial cells synthesize and release signaling molecules to sense the presence of each other, conducing to the formation of microcolony and maturation of biofilms; and (v) dispersal/detachment phase, where the bacterial cells depart biofilms and comeback to independent planktonic lifestyle. Biofilm formation is detrimental in healthcare, drinking water distribution systems, food, and marine industries, etc. As a result, current studies have been focused toward control and prevention of biofilms. In an effort to get rid of harmful biofilms, various techniques and approaches have been employed that interfere with bacterial attachment, bacterial communication systems (quorum sensing, QS), and biofilm matrixs. Biofilms, however, also offer beneficial roles in a variety of fields including applications in plant protection, bioremediation, wastewater treatment, and corrosion inhibition amongst others. Development of beneficial biofilms can be promoted through manipulation of adhesion surfaces, QS and environmental conditions. This review describes the events involved in bacterial biofilm formation, lists the negative and positive aspects associated with bacterial biofilms, elaborates the main strategies currently used to regulate establishment of harmful bacterial biofilms as well as certain strategies employed to encourage formation of beneficial bacterial biofilms, and highlights the future perspectives of bacterial biofilms.

Enhanced CO2 Conversion to Acetate through Microbial Electrosynthesis (MES) by Continuous Headspace Gas Recirculation

Bioelectrochemical systems (BESs) is a term that encompasses a group of novel technologies able to interconvert electrical energy and chemical energy by means of a bioelectroactive biofilm. Microbial electrosynthesis (MES) systems, which branch off from BESs, are able to convert CO2 into valuable organic chemicals and fuels. This study demonstrates that CO2 reduction in MES systems can be enhanced by enriching the inoculum and improving CO2 availability to the biofilm. The proposed system is proven to be a repetitive, efficient, and selective way of consuming CO2 for the production of acetic acid, showing cathodic efficiencies of over 55% and CO2 conversions of over 80%. Continuous recirculation of the gas headspace through the catholyte allowed for a 44% improvement in performance, achieving CO2 fixation rates of 171 mL CO2 L−1·d−1, a maximum daily acetate production rate of 261 mg HAc·L−1·d−1, and a maximum acetate titer of 1957 mg·L−1. High-throughput sequencing revealed that CO2 reduction was mainly driven by a mixed-culture biocathode, in which Sporomusa and Clostridium, both bioelectrochemical acetogenic bacteria, were identified together with other species such as Desulfovibrio, Pseudomonas, Arcobacter, Acinetobacter or Sulfurospirillum, which are usually found in cathodic biofilms. Moreover, results suggest that these communities are responsible of maintaining a stable reactor performance.

Enhancing Stability of Microalgae Biocathode by a Partially Submerged Carbon Cloth Electrode for Bioenergy Production from Wastewater

The electricity output from microbial fuel cell (MFC) with a microalgae assisted cathode is usually higher than that with an air cathode. The output of electricity from a photosynthetic microalgae MFC was positively correlated with the dissolved oxygen (DO) level in the microalgae assisted biocathode. However, DO is highly affected by the photosynthesis of microalgae, leading to the low stability in the electricity output that easily varies with the change in microalgae growth. In this study, to improve the electricity output stability of the MFC, a partially submerged carbon cloth cathode electrode was first investigated to use oxygen from both microalgae and air, with synthetic piggery wastewater used as the anolyte and anaerobically digested swine wastewater as the catholyte. When the DO levels dropped from 13.6–14.8 to 1.0–1.6 mg/L, the working voltages in the MFCs with partially submerged electrodes remained high (256–239 mV), whereas that for the conventional completely submerged electrodes dropped from 259 to 102 mV. The working voltages (average, 297 ± 26 mV) of the MFCs with the 50% submerged electrodes were significantly (p < 0.05) higher than with other partially or completely submerged electrodes. The associated maximum lipid production from wastewater was 250 ± 42 mg/L with lipid content of 41 ± 6% dry biomass. Although the partially submerged electrode had no significant effects on lipid production or nitrogen removal in wastewater, there was significant improvement in the stability of the electricity generated under variable conditions.

Revisiting the mechanistic pathways for bacterial mediated synthesis of noble metal nanoparticles

Synthesis and application of reliable nanoscale materials is a progressive domain and the limelight of modern nanotechnology. Conventional physicochemical approaches for the synthesis of metal nanoparticles have become obsolete owing to costly and hazardous materials. There is a need to explore alternative, cost-effective and eco-friendly strategies for fabrication of nanoparticle (NPs). Green synthesis of noble metal nanoparticles has emerged as a promising approach in the last decade. Elucidation of the molecular mechanism is highly essential in the biological synthesis of noble metal nanoparticles (NPs) for the controlled size, shape, and monodispersity. Moreover, mechanistic insights will help to scale up the facile synthesis protocols and will enable biotransformation of toxic heavy metals hence also providing the detoxification effects. Therefore, the current review article has primarily targeted the mechanisms involved in the green synthesis of metal NPs, which have been reported during the last few years. Detailed mechanistic pathways have highlighted nitrate reductase as a principle reducing agent in the bacterial mediated synthesis and stabilization of NPs. Furthermore, we have highlighted the potential implications of these mechanisms in bioremediation and biomineralization processes, which can play a critical role in biogeochemical cycling and environmental impacts of heavy metals. We anticipate that this review article will help researchers to address the challenges of bioremediation and modern nanotechnology.

Microcystis aeruginosa Synergistically Facilitate the Photocatalytic Degradation of Tetracycline Hydrochloride and Cr(VI) on PAN/TiO2/Ag Nanofiber Mats

Cyanobacterial blooms can cause serious damage to aquatic ecosystems. However, we have demonstrated that typical algae-blooming species Microcystis aeruginosa (M. aeruginosa) combined with photocatalysts could synergistically facilitate the photodecontamination of tetracycline hydrochloride (TC) and Cr(VI). In this study, for the first time, harmful algae were successfully converted into photoreactive bionano hybrid materials by immobilizing M. aeruginosa cells onto polyacrylonitrile (PAN)-TiO2/Ag hybrid nanofibers, and their photocatalytic activity was evaluated. The addition of M. aeruginosa significantly improved the photodecontamination, and the reaction rate constant (k) values of TC and Cr(VI) degradation by M. aeruginosa-PAN/TiO2/Ag nanofiber mats were 2.4 and 1.5-fold higher than that of bare PAN/TiO2/Ag nanofiber. Photoreaction caused damage to algae cells, but no microcystin was found that had been photodegraded simultaneously. The effects of various active species were also investigated, and the photodegradation mechanism was proposed. Recycling tests revealed that this flexible M. aeruginosa-PAN/TiO2/Ag hybrid mat had potential application in the removal of mixed organic and inorganic pollutants with high efficiency and without secondary pollutants. Thus, harmful algae blooms could serve as an efficient materials to remove toxic pollutants in a sustainable way under visible light irradiation.

Fungi-Based Microbial Fuel Cells

Fungi are among the microorganisms able to generate electricity as a result of their metabolic processes. Throughout the last several years, a large number of papers on various microorganisms for current production in microbial fuel cells (MFCs) have been published; however, fungi still lack sufficient evaluation in this regard. In this review, we focus on fungi, paying special attention to their potential applicability to MFCs. Fungi used as anodic or cathodic catalysts, in different reactor configurations, with or without the addition of an exogenous mediator, are described. Contrary to bacteria, in which the mechanism of electron transfer is pretty well known, the mechanism of electron transfer in fungi-based MFCs has not been studied intensively. Thus, here we describe the main findings, which can be used as the starting point for future investigations. We show that fungi have the potential to act as electrogens or cathode catalysts, but MFCs based on bacteria–fungus interactions are especially interesting. The review presents the current state-of-the-art in the field of MFC systems exploiting fungi.

Separation of Acetate Produced from C1 Gas Fermentation Using an Electrodialysis-Based Bioelectrochemical System

The conversion of C1 gas feedstock, such as carbon monoxide (CO), to useful platform chemicals has attracted considerable interest in industrial biotechnology. One conversion method is electrode-based electron transfer to microorganisms using bioelectrochemical systems (BESs). In this BES system, acetate is the predominant component of various volatile fatty acids (VFAs). To appropriately separate and concentrate the acetate produced, a BES-type electrodialysis cell with an anion exchange membrane was constructed and evaluated under various operational conditions, such as applied external current, acetate concentration, and pH. A high acetate flux of 23.9 mmol/m2∙h was observed under a −15 mA current in an electrodialysis-based bioelectrochemical system. In addition, the initial acetate concentration affected the separation efficiency and transportation rate. The maximum flux appeared at 48.6 mmol/m2∙h when the acetate concentration was 100 mM, whereas the effects of the initial pH of the anolyte were negligible. The acetate flux was 14.9 mmol/m2∙h when actual fermentation broth from BES-based CO fermentation was used as a catholyte. A comparison of the synthetic broth with the actual fermentation broth suggests that unknown substances and metabolites produced from the previous bioconversion process interfere with electrodialysis. These results provide information on the optimal conditions for the separation of VFAs produced by C1 gas fermentation through electrodialysis and a combination of a BES and electrodialysis.