Distribution of Some Ecotoxic Elements in Fuel and Solid Combustion Residues in Poland

Distribution of As within Magnetic and Non-Magnetic Fractions of Fluidized-Bed Coal Combustion Ash

Separation of coal ash into magnetic and non-magnetic fractions facilitates their utilization when processed separately. Due to desulphurization additives added to coal during the fluidised-bed combustion, non-magnetic fractions often contain elevated CaO levels (while magnetic concentrates are typically rich in Fe2O3). Both CaO and Fe2O3 are known for their ability to bind As during the combustion, whose distribution is a crucial parameter in terms of proper utilization of these fractions. Therefore, the study deals with the As partitioning within magnetic and non-magnetic fractions of fluidized-bed coal combustion ashes. Two different (successive) procedures of dry magnetic separation were used to separate each ash into strongly magnetic, less magnetic, and a non-magnetic fraction. Due to their optimal utilization, the concentrations of As and other target elements in these fractions were evaluated and compared. Magnetic concentrates from the first separation step (in vibrofluidized state) contained 60–70% Fe2O3, magnetic concentrates separated manually out of the residues after the first separation contained 26–41% Fe2O3, and the non-magnetic residues contained 2.4–3.5% Fe2O3. Arsenic levels were the highest in the non-magnetic residues and gradually decreased with the increasing Fe2O3 content in the magnetic fractions. The dominant As association in the studied samples was to CaO (r = +0.909) and with SO3 (r = +0.906) whereas its joint occurrence with Fe2O3 was improbable (r = −0.834).

Distribution and Mode of Occurrence of Co, Ni, Cu, Zn, As, Ag, Cd, Sb, Pb in the Feed Coal, Fly Ash, Slag, in the Topsoil and in the Roots of Trees and Undergrowth Downwind of Three Power Stations in Poland

It is supposed that the determination of the content and the mode of occurrence of ecotoxic elements (EE) in feed coal play the most significant role in forecasting distribution of EE in the soil and plants in the vicinity of power stations. Hence, the aim of the work was to analyze the properties of the feed coal, the combustion residues, and the topsoil which are reached by EE together with dust from power stations. The mineral and organic phases, which are the main hosts of EE, were identified by microscopy, X-ray powder diffraction, inductively coupled plasma atomic emission spectrometry, and scanning electron microscope with an energy dispersive X-ray methods. The highest content of elements was observed in the Oi and Oe subhorizons of the topsoil. Their hosts are various types of microspheres and char, emitted by power stations. In the areas of long-term industrial activity, there are also sharp-edged grains of magnetite emitted in the past by zinc, lead, and ironworks. The enrichment of the topsoil with these elements resulted in the increase in the content of EE, by between 0.2 times for Co; and 41.0 times for Cd in the roots of Scots pine, common oak and undergrowth, especially in the rhizodermis and the primary cortex and, more seldom, in the axle roller and cortex cells.

Behavior of Cd during Coal Combustion: An Overview

Due to the unfavorable combination of its toxicity and high volatility, Cd is contained in most lists of potentially hazardous air pollutants with the greatest environmental and human-health concerns. The review paper evaluates the behavior of Cd during combustion (incineration) processes and its redistribution among condensed fractions (bottom ash/slag, fly ash) and volatilized fractions (that passes through most particulate control devices). The paper addresses all important effects of Cd interactions, such as presence of organic or inorganic chlorides, moisture levels, S, P and Na concentrations, flue gas composition etc. Possibilities of using various adsorbents (either within in-furnace regime or applied in post-combustion zone) are evaluated as well. Special attention is paid to mitigating its emissions factors; decreasing Cd volatility and facilitating Cd retention are discussed with the view of various combustion (incineration) conditions and the feed fuel composition.

Energy Savings Associated with the Use of Fly Ash and Nanoadditives in the Cement Composition

The paper presented herein investigates the effects of using supplementary cementitious materials (SCMs) in quaternary mixtures on the compressive strength and splitting tensile strength of plain concrete. In addition, environmental benefits resulting from the proposed solutions were analysed. A total of four concrete mixtures were designed, having a constant water/binder ratio of 0.4 and total binder content of 352 kg/m3. The control mixture only contained ordinary Portland cement (OPC) as binder, whereas others incorporated quaternary mixtures of: OPC, fly ash (FA), silica fume (SF), and nanosilica (nS). Based on the obtained test results, it was found that concretes made on quaternary binders containing nanoadditives have very favorable mechanical parameters. The quaternary concrete containing: 80% OPC, 5% FA, 10% SF, and 5% nS have shown the best results in terms of good compressive strength and splitting tensile strength, whereas the worst mechanical parameters were characterized by concrete with more content of FA additive in the concrete mix, i.e., 15%. Moreover, the results of compressive strength and splitting tensile strength are qualitatively convergent. Furthermore, reducing the amount of OPC in the composition of the concrete mix in quaternary concretes causes environmental benefits associated with the reduction of: raw materials that are required for burning clinker, electricity, and heat energy in the production of cement.