Microwave Technology Using Low Energy Concentrated Beam for Processing of Solid Waste Materials from Rapana thomasiana Seashells

Microwave Soldering of Low-Resistance Conductive Joints-Technical and Economic Aspects

Soldering processes are applied in the fabrication of electronic circuits used in most modern domestic and industrial technologies. This article aims to introduce a new soldering technology based on the microwave joining of copper materials used in electronic applications. The study was focused on microwave technology used as the thermal source for soldering. A simulation model of temperature distributions in copper plates with overall dimensions of 50 × 10 × 0.8 mm was developed in order to determine the necessary microwave power for soldering. For 270 °C simulated on the surface of copper plates, the microwave-injected power was determined to be 598.89 W. An experimental program for 600, 650, 700, and 750 W was set in order to achieve soldering of copper plates in less than 1 min. Soldered copper plates were subject to electrical resistance measurements being obtained with variations up to ±1.5% of the initial electrical resistance of the base materials. The quality of joints has also been analyzed through microscopy after the soldering process. In addition, mechanical properties were determined using a universal testing machine. The results have shown similar behavior of the samples layered with SAC on the one-side and double-side but also a significantly lower force before breaking for one-side-layered samples. An economic analysis was performed and the results obtained have shown that in terms of energy efficiency and total costs for microwave soldering compared with manual soldering, microwave soldering is cost-effective for industrial processing.

Hydroxyapatite from Natural Sources for Medical Applications

The aim of this work is to study the physical-chemical, mechanical, and biocompatible properties of hydroxyapatite obtained by hydrothermal synthesis, at relatively low temperatures and high pressures, starting from natural sources (Rapana whelk shells), knowing that these properties influence the behavior of nanostructured materials in cells or tissues. Thus, hydroxyapatite nanopowders were characterized by chemical analysis, Fourier-transform infrared spectroscopy (FT-IR), dynamic light scattering (DLS), scanning electron microscopy (SEM), and X-ray diffraction (XRD). In vitro studies on osteoblast cell lines (cytotoxicity and cell proliferation), as well as preliminary mechanical tests, have been performed. The results showed that the obtained powders have a crystallite size below 50 nm and particle size less than 100 nm, demonstrating that hydrothermal synthesis led to hydroxyapatite nanocrystalline powders, with a Ca:P ratio close to the stoichiometric ratio and a controlled morphology (spherical particle aggregates). The tensile strength of HAp samples sintered at 1100 °C/90 min varies between 37.6–39.1 N/mm². HAp samples sintered at 1300 °C/120 min provide better results for the investigated mechanical properties. The coefficient of friction has an appropriate value for biomechanical applications. The results of cell viability showed that the cytotoxic effect is low for all tested samples. Better cell proliferation is observed for osteoblasts grown on square samples.

Reducing NOx Emissions through Microwave Heating of Aftertreatment Systems for Sustainable Transport in the Inland Waterway Sector

The inland navigation sector makes a significant contribution to the growth of the global economy as well as to climate change due to pollutants emitted by diesel engines. NOx emissions are very high in port areas where, due to traffic, the ships run at idling regimes. Selective catalytic reduction (SCR) represents one of the most suitable technologies, in terms of cost effectiveness, but does not perform well if the temperature during vessel operation is lower than 180 °C. Microwave technology can support preheating of the ceramic core of SCR in order to increase the temperature towards the optimal interval for the best NOx reduction. Research has focused on coupling a magnetron head to a SCR device in order to evaluate to what extent the technology can meet the requirements of Stage V of the European Directive related to NOx emissions. Measurements of NOx emitted have been performed on engines with 603.5 kW nominal power and 1500 rpm that operate at a lower engine speed (700–1200 rpm) and output power (58–418 kW). The values recorded for emissions using microwave heating of ceramic core of SCR have decreased by 89% for a constant load of engine and idling engine speed.