Combustion Characterisation of Bituminous Coal and Pinus Sawdust Blends by Use of Thermo-Gravimetric Analysis

Experimental investigation on the effect of blending bituminous coal with pinus sawdust on combustion performance parameters

Combustion of bituminous coal and pinus sawdust blends was investigated experimentally within a drop tube furnace (DTF) with the aim of determining particle residence times and temperatures during the process. Evaluation of these parameters gives useful information to engineers who want to optimise the co-combustion process of coal and biomass blends. The DTF experimental approach was used to investigate fuel blends with a pinus sawdust mass substitution of 0, 10, 20, and 30% at different furnace temperatures of 1273, 1473 and 1673 K. Results showed that during stage 1 of the experimental setup which mimics devolatilisation, particle residence time at a distance of 520 mm from the injection point decreased from 0.8 to 0.7 s as blending by pinus sawdust increased from 0 to 30 %. During stage 2 of the experimental setup which mimics char combustion, particle residence time at a distance of 1320 mm from the injection point decreased from 3.9 to 2.0 s as blending by pinus sawdust increased from 0 to 30 %. The blending ratios under investigation demonstrated similar profiles of particle temperature at different furnace positions though further analysis showed that the highly blended samples required less time to attain high temperatures. By extension, since fuel blends with higher percentages of pinus sawdust were able to attain higher temperatures at shorter residence time, combustion intensity was deduced to increase with the blending ratio whilst stability decreased. As such, caution should be taken with materials used for furnace and burner design as high-temperature zones move backwards towards the injection point as blending increases.

Possible Utilization of Distillery Waste in the Carbonization Process

This paper characterizes the carbonization process in terms of the utilization of distillery waste in a laboratory-scale reactor. Due to the increase in market prices of wood and environmental protection laws, biomass waste, including distillery waste, is a potential source for biochar production. An experimental investigation of the carbonization process was carried out for different mixtures of distillery waste and oak sawdust. The obtained results showed that due to the European Standard, biochar from distillery waste could be used for the production of charcoal briquettes for barbecue applications. In addition, biochar from carbonization samples with 66, 50, and 33% distillery waste meet the standards defined by the International Biochar Initiative for HMs content. The analysis of the dynamics of the heating rate showed that adding wood to distillery waste significantly shortens the carbonization process, but this reduces the number of bio-oils produced and its calorific value.

Determination of Cocombustion Kinetic Parameters for Bituminous Coal and Pinus Sawdust Blends

Cocombustion of bituminous coal (HC) and Pinus sawdust (PS) was investigated in this paper with the aim of determining the kinetic parameters relevant to cocombustion reactions of their fuel blends. PS was used because it is a waste biomass product capable of generating energy. Motivated by the need to partly substitute HC used in existing boilers with PS, the optimum kinetic parameters at different blending ratios were thus investigated with the ultimate goal of diversifying the energy portfolio for these boilers. Blended samples were prepared with a PS substitution by mass ranging from 0 to 30%, thus producing five samples, namely:100HC, 90HC10PS, 80HC20PS, 70HC30PS, and 100PS. A simultaneous thermogravimetric analyzer was used to investigate the degradation of the fuel samples under a synthetic air atmosphere using 5, 12.5, and 20 °C/min heating rates. The kinetic parameters were evaluated using the distributed activation energy model (DAEM) due to its ability to evaluate complex parallel chemical mechanisms. The influential homogenous volatile combustion and heterogenous combustion stages produced an increasing trend for activation energy (E _a) with increased PS (100HC to 70HC30PS) from an average of 61.80-104.34 kJ/mol while the pre-exponential factor increased from 1.31 × 10⁵ to 6.52 × 10⁸. Generally, blending of HC with PS did not produce a linear variation of the kinetic parameters; thus, by using various plots, an optimum blending ratio of 80HC20PS was deduced.

Physicochemical Properties of Biochar Produced from Goldenrod Plants

Torrefaction is one of the methods of thermal treatment of biomass, which allows obtaining a product of better quality in the form of biochar. The aim of the paper was to analyze the possibility of using goldenrod (Solidago canadensis, Solidago gigantea) for the production of biochar. The torrefaction process involved the vegetative and generative parts as well as the whole plant at temperatures of 250 °C and 275 °C, for 3 h. Next, the physicochemical properties of the raw material and biochar were determined, namely moisture content, ash content, volatile matter content, calorific value, and heat of combustion. The bulk density of raw biomass and biochar was also determined. It was found that after biomass torrefaction, the ash content, calorific value, and heat of combustion increased, while volatile matter content decreased. It has been observed that in both the case of raw biomass and biochar, the plant species and the sampled parts have a significant impact on the ash content, volatile matter content, calorific value, and heat of combustion.