Application of Capillary Polypropylene Membranes for Microfiltration of Oily Wastewaters: Experiments and Modeling

The Application of Polyethersulfone Ultrafiltration Membranes for Separation of Car Wash Wastewaters: Experiments and Modelling

The wastewater generated as a result of car washes is considered a new source of water. However, recovered water must meet the required quality criteria for reuse. For this purpose, the ultrafiltration (UF) process can be successfully used. The main aim of the present work was to investigate the influence of the membrane's molecular weight cut-off (MWCO) on the UF performance in terms of the fouling phenomenon and retention degree of car wash wastewater. Moreover, for a better understanding of the fouling mechanisms, Hermia's model was used. The experimental studies were conducted with the use of two polyethersulfone (PES) membranes (MWCO of 10 kDa and 100 kDa). It has been noted that the used membranes provided a high-quality permeate and excellent turbidity removal, up to 99%. Moreover, it has been noted that the MWCO membrane has a significant impact on the fouling mechanism. Generally, a much greater intensity of fouling for the membrane with MWCO of 100 kDa was observed. Results obtained in the present study showed that both real wastewaters and the clean solutions used for washing cars cause the fouling phenomenon. It has been proven that rinsing the membranes with water is not sufficient to recover the initial membrane's performance. Hence, periodic chemical cleaning of the membranes was required. Fitting the experimental data to Hermia's model allowed us to indicate that membranes with MWCO of 100 kDa are more prone to intermediate blocking. To sum up, the findings suggest that for the UF of the car wash wastewater, the use of membranes with MWCO equal to 10 kDa is recommended.

Wettability Studies of Capillary PTFE Membranes Applied for Membrane Distillation

In the present study, the membrane distillation (MD) process was studied with the use of commercial polytetrafluoroethylene (PTFE) capillary membranes. For this purpose, both solutions with NaCl concentrations up to 300 g/L and brines contaminated with oil (70-120 mg/L) were used as feeds. The membrane's wetting resistance was tested by conducting long-term experiments for over 3500 h. Using detailed studies, it has been shown that increasing the salt concentration from 35 to 300 g/L resulted in a 50% reduction in the permeate flux. Nevertheless, the membranes retained 100% of the salt rejection after 2000 h of the module's operation. Moreover, it has been found that performing the MD process with brines contaminated with oil (120 mg/L) led to the wetting of some membranes pores, which it turn resulted in an increase in the distillate's conductivity to 450 µS/cm after 700 h running the process. The mechanism of pore wetting by oil droplets adsorbed on the membrane's surface was presented. Finally, the proposed method of membrane cleaning with the use of a solvent allowed restoring the initial MD module's performance. Consequently, both the permeate flux and distillate conductivity were stable during the MD of the feed containing 35 g/L of NaCl over the next 280 h.

New Low-Cost Ceramic Microfiltration Membranes for Bacteria Removal

Safe water provision in low-income countries is constrained by limited financial resources, and the problem is worsened during natural disasters. Thus, there is a need to develop efficient low-cost technologies for point-of-use water treatment. This work reports on the development of new ceramic microfiltration membranes made from mixtures of inexpensive raw materials available locally (kaolin, bentonite and limestone) and their efficiency in rejecting bacteria such as Escherichia coli and Staphylococcus aureus. Thermogravimetric analysis, differential scanning calorimetry, Fourier-transform infrared spectroscopy, X-ray diffraction, mercury intrusion porosimetry, flexural strength and water uptake were used to characterize the raw materials and membranes. The addition of limestone in the membrane fabrication increased the pore size, the porosity and, thus, the permeability of the membranes but at the expense of the rejection performance. Among the different compositions studied, the membrane made of 83% kaolin, 10% bentonite and 7% limestone showed the best performance compromise with water permeability of 566 L·h⁻¹·m⁻²·bar⁻¹ and 100% rejection of both Escherichia coli and Staphylococcus aureus. These new low-cost microfiltration membranes are expected to have potential applications in water treatment and household applications.

Review of New Approaches for Fouling Mitigation in Membrane Separation Processes in Water Treatment Applications

This review investigates antifouling agents used in the process of membrane separation (MS), in reverse osmosis (RO), ultrafiltration (UF), nanofiltration (NF), microfiltration (MF), membrane distillation (MD), and membrane bioreactors (MBR), and clarifies the fouling mechanism. Membrane fouling is an incomplete substance formed on the membrane surface, which will quickly reduce the permeation flux and damage the membrane. Foulant is colloidal matter: organic matter (humic acid, protein, carbohydrate, nano/microplastics), inorganic matter (clay such as potassium montmorillonite, silica salt, metal oxide, etc.), and biological matter (viruses, bacteria and microorganisms adhering to the surface of the membrane in the case of nutrients) The stability and performance of the tested nanometric membranes, as well as the mitigation of pollution assisted by electricity and the cleaning and repair of membranes, are reported. Physical, chemical, physico-chemical, and biological methods for cleaning membranes. Biologically induced biofilm dispersion effectively controls fouling. Dynamic changes in membrane foulants during long-term operation are critical to the development and implementation of fouling control methods. Membrane fouling control strategies show that improving membrane performance is not only the end goal, but new ideas and new technologies for membrane cleaning and repair need to be explored and developed in order to develop future applications.