Analysis by UAV Digital Photogrammetry of Folds and Related Fractures in the Monte Antola Flysch Formation (Ponte Organasco, Italy)

An Open-Source Algorithm for 3D ROck Slope Kinematic Analysis (ROKA)

The Markland test is one of the most diffused and adopted methods of kinematic analysis for the identification of critical intersections of rock discontinuities that could generate rock failures. Traditionally, the kinematic analysis is based on the use of a stereographic approach that is able to identify the critical combination between the orientations of discontinuities and the rock wall. The recent improvements in the use of Digital Outcrop Models (DOMs) created the conditions for the development of a new automatized approach. We present ROck Slope Kinematic Analysis (ROKA) which is an open-source algorithm aimed at performing the Kinematic Analysis using the discontinuity measures collected onto a 3D DOM. The presented algorithm is able to make a local identification of the possible critical combination between the identified discontinuities and the orientation of the slope. Using this approach, the algorithm is able to identify on the slope the presence of critical combinations according to the traditional kinematic analysis of planar failure, flexural toppling, wedge failure, and direct toppling modes of failures and then visualize them on DOMs. In this way, the traditional approach is more effective and can be adopted for a more detailed analysis of large and complex areas.

Reliability and Uncertainties of the Analysis of an Unstable Rock Slope Performed on RPAS Digital Outcrop Models: The Case of the Gallivaggio Landslide (Western Alps, Italy)

A stability investigation based on Digital Outcrop Models (DOMs) acquired in emergency conditions by photogrammetric surveys based on Remote Piloted Aerial System (RPAS) was conducted on an unstable rock slope near Gallivaggio (Western Alps, Italy). The predicted mechanism of failure and volume of the unstable portion of the slope were successively verified on the DOMs acquired after the rockfall that effectively collapsed the May 29th, 2018. The comparison of the pre- and post-landslide 3D models shows that the estimated mode of failure was substantially correct. At the same time, the predicted volume of rock involved in the landslide was overestimated by around 10%. To verify if this error was due to the limited accuracy of the models georeferenced in emergency considering only the Global Navigation Satellite System/Inertial Measurement Unit (GNSS/IMU)-information of RPAS, several Ground Control Points (GCPs) were acquired after the failure. The analyses indicate that the instrumental error in the volume calculation due to the direct-georeferencing method is only of the 1.7%. In contrast, the significant part is due to the geological uncertainty in the reconstruction of the real irregular geometry of the invisible part of the failure surface. The results, however, confirm the satisfying relative accuracy of the direct-georeferenced DOMs, compatible with most geological and geoengineering purposes.

The Use of Precise Survey Techniques to Find the Connection between Discontinuities and Surface Morphologic Features in the Laže Quarry in Slovenia

This paper addresses a stability evaluation of artificial slopes in a quarry located in Slovenia that was affected by a rockslide in March 2019. In order to ensure the safety of further production, measures were taken to restore the slopes. A stability assessment of the remaining parts of the quarry was conducted. To ensure quality spatial data, an upgraded study based on terrain mapping and aerial photogrammetric imaging using an unmanned aircraft was carried out, in addition to a traditional field survey of the quarry. So that the data were qualitatively useful, a digital terrain and discontinuity model was developed. Projections of the discontinuities occurring in the quarry and in the wider area were determined. The focus of the modeling was finding the main systems of discontinuities and projecting these systems onto the unexcavated parts of the quarry.

Application of UAV in Topographic Modelling and Structural Geological Mapping of Quarries and Their Surroundings-Delineation of Fault-Bordered Raw Material Reserves

A 3D surface model of an active limestone quarry and a vegetation-covered plateau was created using unmanned aerial vehicle (UAV) technique in combination with terrestrial laser scanning (TLS). The aim of the research was to identify major fault zones that dissect the inaccessible quarry faces and to prepare a model that shows the location of these fault zones at the entire study area. An additional purpose was to calculate reserves of the four identified lithological units. It was only possible to measure faults at the lowermost two meters of the quarry faces. At the upper parts of the quarry and on the vegetation-covered plateau where no field geological information was available, remote sensing was used. Former logs of core drillings were obtained for the modelling of the spatial distribution of four lithological units representing cover beds and various quality of limestone reserves. With the comparison of core data, field measurements and remote sensing, it was possible to depict major faults. Waste material volumes and limestone reserves were calculated for five blocks that are surrounded by these faults. The paper demonstrates that, with remote sensing and with localised control field measurements, it is possible: (a) to provide all geometric data of faults and (b) to create a 3D model with fault planes even at no exposure or at hardly accessible areas. The surface model with detected faults serves as a basis for calculating geological reserves.