Salt Spray and Surfactants Induced Morphological, Physiological, and Biochemical Responses in Callistemon citrinus (Curtis) Plants

High-sensitivity optical fiber probe for simultaneous measurement of chloride ions and temperature

A fiber optic probe for the simultaneous measurement of chloride ions and temperature is presented. The Ag/alginate composite film is used as the reflective surface of the Fabry-Perot interferometer (FPI) and is a sensitive film for the adsorption of chloride ions. The experimental results show that the Fabry-Perot (FP) response sensitivity is approximately 1.4689 nm/µM as the chloride ion concentration changes from 1 to 9 µM, but the fiber Bragg grating (FBG) is insensitive to chloride ions. When the temperature is changed from 35°C to 80°C, the response sensitivities of the FP and the FBG are about 0.7 and 0.01115 nm/°C, respectively.

Resistance of Mycorrhizal Cinnamomum camphora Seedlings to Salt Spray Depends on K+ and P Uptake

Salt spray is a major environmental issue in coastal areas. Cinnamomum camphora is an economically important tree species that grows in the coastal areas of southern China. Arbuscular mycorrhizal fungi (AMF) can alleviate the detrimental effects of abiotic stress on host plants. However, the mechanism by which AMF mitigates the adverse effects of salt spray on C. camphora remains unclear. A pot experiment was conducted in a greenhouse, where C. camphora seedlings were exposed to four AMF regimes (inoculation with sterilized fungi, with Glomus tortuosum, Funneliformis mosseae, either alone or in combination) and three salt spray regimes (applied with distilled water, 7, and 14 mg NaCl cm-2) in order to investigate the influence on root functional traits and plant growth. The results showed that higher salt spray significantly decreased the K+ uptake, K+/Na+ ratio, N/P ratio, total dry weight, and salinity tolerance of non-mycorrhizal plants by 37.9%, 71%, 27.4%, 12.7%, and 221.3%, respectively, when compared with control plants grown under non-salinity conditions. Mycorrhizal inoculation, particularly with a combination of G. tortuosum and F. mosseae, greatly improved the P uptake, total dry weight, and salinity tolerance of plants grown under higher salt spray conditions by 51.0%, 36.7%, and 130.9%, respectively, when compared with their counterparts. The results show that AMF can alleviate the detrimental effects of salt spray on C. camphora seedlings. Moreover, an enhanced uptake of K+ and P accounted for the resistance of the plants to salt spray. Therefore, pre-inoculation with a combination of G. tortuosum and F. mosseae to improve nutrient acquisition is a potential method of protecting C. camphora plants against salt spray stress in coastal areas.

Analysis of plant cuticles and their interactions with agrochemical surfactants using a 3D printed diffusion chamber

BACKGROUND

Decades of research is available on their effects of single component surfactant on active ingredient diffusion across plant cuticular membranes, but ingredient diffusion is rarely analysed in the presence of commercial surfactants. Also, diffusion studies require expensive or specialized apparatus the  fabrication of which often requires skilled labour and specialized facilities. In this research we have addressed both problems where the effects of four commercially available surfactants on a known tracer molecule were investigated using a 3D printed customized diffusion chamber.

RESULTS

As a proof-of-concept a customized 3D printed diffusion chamber was devised using two different thermoplastics and was successfully used in a range of diffusion tests . The effect of various solvents and surfactants on S. lycopersicum cuticular membrane indicated an increased rate of flux of tracer molecules across the membranes. This research has validated the application of 3D printing in diffusion sciences and demonstrated the flexibility and potential of this technique.

CONCLUSIONS

Using a 3D printed diffusion apparatus, the effect of commercial surfactants on molecular diffusion through isolated plant membranes was studied. Further, we have included  here the steps involved in material selection, design, fabrication, and post processing procedures for successful recreation of the chamber. The customizability and rapid production process of the 3D printing demonstrates the power of additive manufacturing in the design and use of customizable labware.