Effect of UVC and UVA Photocatalytic Processes on Tetracycline Removal Using CuS-Coated Magnetic Activated Carbon Nanocomposite: A Comparative Study

Preparation of magnetite nanoparticles and their application in the removal of methylene blue dye from wastewater

Wastewater is discharged in large amounts from different industries; thus, wastewater treatment is currently one of the main concerns, advanced oxidation is a promising technique for wastewater treatment. This research aims to synthesize magnetite nanoparticles and study their application in wastewater treatment via adsorption and advanced oxidation processes. Magnetite nanoparticles were synthesized via coprecipitation technique between ferric and ferrous sulfate at a molar ratio of 2:1. The prepared sample was characterized using FTIR, XRD, TEM, BET surface area, zeta potential, VSM, and UV‒visible spectroscopy. XRD confirmed the formation of a single face-centered cubic (FCC) spinel structure of Fe3O4. TEM revealed an average particle size of 29.2 nm and a BET surface area of 70.1 m2 g-1. UV‒visible spectroscopy revealed that the UV-visible peak of the sample was obtained at 410 nm. VSM confirmed the attraction of the sample to a magnet with a magnetization of 60 (emu/g). The removal efficiency of methylene blue was studied using adsorption and advanced oxidation methods. For adsorption, the studied parameters were dye concentration 2-10 ppm, 3-10 pH, and 50:300 mg Fe3O4/L. For advanced oxidation, peroxide was used with nanomagnetite as a catalyst, and the studied parameters were pH 2-11, magnetite dose 20-200 PPM, and peroxide dose 500-2000 PPM. The removal efficiency by adsorption reached 95.11% by adding 50 mg of Fe3O4/L and 10 ppm dye conc at 6.5 pH; on the other hand, in advanced oxidation, it reached 98.5% by adding 110 PPM magnetite and 2000 ppm H2O2 at pH 11. The magnetite nanoparticles were reused for ten cycles of advanced oxidation, for a 10% reduction in removal efficiency at the tenth cycle.

Enhanced removal of tetrabromobisphenolA (TBBPA) from e-waste by Fe-S nanoparticles and Fe-S/CuS nanocomposite with response surface methodology (RSM)

TetrabromobisphenolA is a well-known member of the brominated flame retardant group and is widely used as a highly effective fire-retardant additive in electronic and electrical equipment. TBBPA is commonly found in various environmental sources and can be harmful to human health. This study presents a simple approach to preparing a magnetic nanocomposite, offering a straightforward method that results in consistent quality and low resource consumption. The nanocomposite has a high surface-to-volume ratio for the removal of tetrabromobisphenolA. Various characterization techniques, including XRD, FTIR, EDX, FESEM, VSM, TEM, and BET analyses were used to characterize the Fe-S nanoparticles and Fe-S/CuS. The results showed that Fe-S/CuS nanocomposite successfully removed over 97% of the initial TBBPA (15 mg L-1) under optimized conditions determined by RSM, such as a contact time of 15 min, pH of 7, Fe-S/CuS nanocomposite dosage of 0.69 g L-1, and salt concentration of 0.10%. The RSM analysis provided a second-order polynomial model with a confidence level of 93% (F = 29.58; p < 0.0001) to predict the TBBPA removal efficiency at various concentrations. In the adsorption kinetic studies, the second-order kinetic model provided the best fit for the experimental data. Additionally, Fe-S/CuS nanocomposite shows great potential for practical applications and environmental remediation efforts, making it a valuable asset for real-sample use in environmental settings.

Enhancement of photocatalytic activity of Ba-doped CoO for degradation of Emamectin benzoate in aqueous solution

The present study was focused on the preparation of cobalt oxide (CoO) and barium-doped cobalt oxide (Ba-doped CoO) by following the co-precipitation method for the degradation of Emamectin benzoate pesticide in the aqueous medium. The prepared catalysts were characterized using SEM, EDX, and XRD to confirm the formation of catalysts and to observe the variation in the composition of catalysts during the degradation study. It can be suggested from the results of SEM, EDX, XRD, and FTIR analyses that Ba atom has successfully incorporated in the crystalline structure of CoO. The degradation of Emamectin benzoate pesticide was studied under the influence of different factors like solution pH, the dose of catalyst, contact time, temperature, and initial concentration of pesticide. It was observed that solution pH affects the degradation of the pesticide, and maximum degradation (23% and 54%) was found at pH 5.0 and 6.0 using CoO and Ba-doped CoO, respectively. The degradation of pesticides was found to be increased continuously (27-35% in case of CoO while 47-58% in case Ba-doped CoO) with the time of contact. However, the degradation was found to be decreased (23-3% in case of CoO while 47-44% in case Ba-doped CoO) with an increase in temperature. Likewise, in the beginning, degradation was observed to be increased up to some extent with the dose of catalyst and initial concentration of pesticide but started to decrease with further augmentation in the dose of catalyst and initial concentration of pesticide. It may be concluded from this study that doping of Ba considerably enhanced the photocatalytic ability of CoO for Emamectin benzoate pesticide.