Synthesis of Porous Polydimethylsiloxane Gold Nanoparticles Composites by a Single Step Laser Ablation Process

Development of a Photothermal Regenerative Plasmonic Platform as a Light-Controlled Interface

This study introduces a novel plasmonic nanocomposite platform, where gold nanoparticles (AuNPs) are synthesized in situ within a polydimethylsiloxane (PDMS) film. The innovative fabrication process leverages ethyl acetate swelling to achieve a uniform distribution of AuNPs, eliminating the need for additional reagents. The resulting nanocomposite film exhibits exceptional photothermal conversion capabilities, efficiently converting absorbed light into heat and rapidly reaching high temperatures. Furthermore, the platform is biofunctionalized with the phosphotriesterase enzyme, not only enabling the degradation of organophosphate pesticides but also showcasing the potential for multifunctional applications. The platform's ability to be regenerated after use underscores its sustainability for repeated applications.

Blue Laser for Production of Carbon Dots

The synthesis of carbon dots (CDs) is gaining wide-ranging interest due to their broad applicability, owing to their small size and luminescence. CDs were prepared from charcoal via a one-step process using laser ablation in liquid without the use of reagents. The adopted method was based on the use of a commercially available continuous wave (CW) laser diode emitting a 450 nm wavelength and, for the liquid, a phosphate-buffered saline (PBS) solution, routinely used in the biological field. Photoluminescence analysis revealed fluorescence, at 480 nm, increasing with laser irradiation time. The atomic force microscopy (AFM) of the CDs revealed an average sphere shape with a size of about 10 nm. Biodegradable polycaprolactone (PCL), typically adopted in biomedicine applications, was used as a matrix to show the preserved luminescence, ideal for the non-invasive monitoring of implanted scaffolds in tissue engineering.

Polyvinylalcohol Composite Filled with Carbon Dots Produced by Laser Ablation in Liquids

Carbon dots (CDs), owing to their excellent photoluminescent features, have been extensively studied for physics preparation methods and for biomedical and optoelectronic device applications. The assessment of the applicability of CDs in the production of luminescent polymeric composites used in LEDs, displays, sensors, and wearable devices is being pursued. The present study reports on an original, environmentally friendly, and low-cost route for the production of carbon dots with an average size of 4 nm by laser ablation in liquid. Jointly, to prove the significance of the study for a wide range of applications, a free-standing flexible polyvinyl alcohol (PVA) composite containing photoluminescent carbon dots was manufactured. CDs were prepared using targets of porose charcoal with a density of 0.271 g/cm3 placed in phosphate-buffered saline (PBS) liquid solution and irradiated for 30 min by pulsed IR diode laser. The optical properties of the obtained suspension containing carbon dots were studied with UV-ViS and FTIR spectroscopies. The photoluminescence of the produced carbon dots was confirmed by the emission peak at 480 nm in the luminescence spectrum. A narrow luminescence band with a full width at half-maximum (FWHM) of less than 40 nm could be an asset in spectral emission analysis in different applications. Atomic force microscopy confirms the feasibility of manufacturing CDs in clean and biocompatible environments, paving the way for an easier and faster production route, crucial for their wider applicability.

Overview of Polyethylene Terephthalate Foils Patterned Using 10 MeV Carbon Ions for Realization of Micromembranes

Polymer membranes are conventionally prepared using high-energy particles from radioactive decay or by the bombardment of hundreds of MeVs energy ions. In both circumstances, tracks of damage are produced by particles/ions passing through the polymer, and successively, the damaged material is removed by chemical etching to create narrow pores. This process ensures nanosized pore diameter but with random placement, leading to non-uniform local pore density and low membrane porosity, which is necessary to reduce the risk of their overlapping. The present study is focused on the use of polyethylene terephthalate (PET) foils irradiated by 10.0 MeV carbon ions, easily achievable with ordinary ion accelerators. The ion irradiation conditions and the chemical etching conditions were monitored to obtain customized pore locations without pore overlapping in PET. The quality, shape, and size of the pores generated in the micromembranes can have a large impact on their applicability. In this view, the Scanning Transmission Ion Microscopy coupled with a computer code created in our laboratory was implemented to acquire new visual and quantitative insights on fabricated membranes.