Hybrid Polyetheretherketone (PEEK)-Acrylic Resin Prostheses and the All-on-4 Concept: A Full-Arch Implant-Supported Fixed Solution with 3 Years of Follow-Up

Outcomes that may affect implant and prosthesis survival and complications in maxillary fixed prosthesis supported by four or six implants: A systematic review and meta-analysis

Objective

To investigate whether the clinical and radiographical outcomes are affected when four or six implants support the maxillary fixed complete denture (FCD).

Materials and methods

This study was registered on PROSPERO (CRD42021226432) and followed the PRISMA guidelines. The focused PICO question was, "For an edentulous maxillary patient rehabilitated with an implant-supported fixed prosthesis, do the clinical and radiographical outcomes differ when four or six implants support the prosthesis ". A thorough search of the relevant studies was designed and performed electronically. The survival rate of implant and prosthesis, marginal bone loss, and complications (mechanical and biological) were the primary outcomes, whereas implant distribution and using the surgical guide, follow-up, and framework material were evaluated as secondary outcomes.

Results

Out of 1099 articles initially retrieved, 53 clearly stated the outcomes of interest and were included in this study. There were no significant differences in implant and prosthesis survival, technical/mechanical complications, and biological complications between the 4-implant group (4-IG) and the 6-implant group (6-IG). However, marginal bone loss (MBL) was significantly higher in the 4-IG (p < 0.01). The surgical guide and follow-up period did not significantly affect implant/prosthesis survival. Additionally, using the CAD/CAM milled framework and anteroposterior implant distribution were associated with significantly higher implant survival in the 6-IG (p < 0.01).

Conclusion

The findings of this study indicated that having a greater number of implants, as seen in the 6-implant group, can lead to a decrease in technical and biological complications and reduce marginal bone loss. It is worth noting that factors such as using CAD/CAM frameworks and the anteroposterior distribution of implants were recognized as important in improving implant survival rates when more implants are present.

Marginal fit and fracture resistance of polyetheretherketone, zirconia, and titanium implant-supported prosthesis frameworks for a partially edentulous arch after thermomechanical aging

STATEMENT OF PROBLEM

Although polyetheretherketone (PEEK) and zirconia (Zir) have been used as implant-supported prosthesis (ISP) frameworks, the long-term effects of thermomechanical aging on the marginal fit and fracture resistance of PEEK and Zir ISP frameworks with titanium (Ti) bases for patients with a partially edentulous arch are not clear.

PURPOSE

The purpose of this in vitro study was to determine the marginal fit and fracture resistance of PEEK and Zir ISP frameworks with Ti bases and Ti ISP frameworks for partially edentulous arches after aging.

MATERIAL AND METHODS

A total of 30 ISP epoxy resin casts were obtained from a typodont with 1 straight implant (Nobel Biocare) in the mandibular right canine region and 1 implant with a 30-degree distal tilt in the mandibular right first molar region. All frameworks (n=10) were fabricated on their own epoxy resin cast with multiunit abutment replicas by using a computer-aided design and computer-aided manufacturing system (exocad-Yenadent). The PEEK and Zir frameworks were fabricated with Ti-bases. Primer (MKZ) and resin cement (DTK adhesive) were used to cement the frameworks to the Ti-bases under a static load of 10 N. After thermomechanical aging (1.2×106 cycles, 120 N, 5 °C-55 °C), marginal gaps between the Ti-bases and cemented frameworks and vertical and passive fits between the Ti-bases and framework and multi-unit abutments were measured by using a stereomicroscope (Euromex) at ×100 magnification. Fracture resistances and types were then determined by using a universal test machine and a stereomicroscope at ×40 magnification. Data were analyzed by using 1-way analysis of variance (ANOVA) and the Tukey HSD and Fisher-Freeman-Halton tests (α=.05).

RESULTS

The marginal gaps of the PEEK and Zir frameworks were respectively 83.5 ±27.1 and 81.8 ±17.8 µm. PEEK (23.7 ±4.6) and Zir (32.9 ±8.7) had a better vertical fit (µm) than Ti (52.5 ±10.6) (P<.001). Zir (49.3 ±16.2) (P<.001) and PEEK (70.9 ±19.6) (P>.05) frameworks had better passive fit (µm) than Ti (91.3 ±24.2). Ti had the highest mean fracture resistance (N) (14800.2 ±3442.3) followed by Zir (7318.7 ±1385.1) and PEEK (3448.9 ±486.6) (P<.001). Fracture types were different in different groups (P<.001).

CONCLUSIONS

The PEEK and Zir frameworks with Ti bases had better vertical and passive fit than the Ti frameworks. All ISP frameworks represented mean marginal fit below 92 µm and withstood physiologic occlusal forces after thermomechanical aging.

The All-on-4 Concept Using Polyetheretherketone (PEEK)-Acrylic Resin Prostheses: Follow-Up Results of the Development Group at 5 Years and the Routine Group at One Year

BACKGROUND

It is necessary to investigate the application of polymer materials in implant dentistry. The aim of this study was to examine the outcome of full-arch polyetheretherketone (PEEK)-acrylic resin implant-supported prostheses.

METHODS

Seventy-six patients were rehabilitated consecutively with 100 full-arch implant-supported prostheses of PEEK-acrylic resin (a development group (DG): 37 patients with 5 years of follow-up; a routine group (RG): 39 patients with 1 year of follow-up). The primary outcome measure was prosthetic survival. Secondary outcome measures were implant survival, marginal bone loss, biological complications, prosthetic complications, veneer adhesion, plaque levels, bleeding levels, and a patient subjective evaluation (including the Oral Health Impact Profile for the RG).

RESULTS

In both groups, prosthetic (DG: 93.6%; RG: 100%) and implant survival (DG: 98.9%; RG: 99.5%) were high, and marginal bone loss was low (DG: 0.54 mm; RG: 0.28 mm). The veneer adhesion rate was 28.6% of prostheses in DG (RG = 0%). Mechanical complications occurred in 49% and 11.8% of prostheses in DG and RG, respectively. Biological complications, plaque, and bleeding levels were low in both groups. The subjective patient evaluation was excellent in both groups (8.6 < DG < 8.8; 9.3 < RG < 9.5; OHIP = 1.38).

CONCLUSIONS

Within the limitations of this study, PEEK can be considered a viable prosthetic alternative.

Hybrid Prosthesis versus Overdenture: Effect of BioHPP Prosthetic Design Rehabilitating Edentulous Mandible

Aim

To compare the BioHPP (biocompatible high-performance polymer) as a substructure for the hybrid prosthesis versus the BioHPP bar supporting and retaining implant overdenture by radiographic evaluation to identify bone height alteration around the implants and to evaluate satisfaction based on visual analoge scale questionnaire.

Materials and Methods

Ill-fitting mandibular dentures were chosen for 14 fully edentulous male patients with adequate dental hygiene, enough interarch space, and free of systemic diseases and parafunctional habits. Patients who received new dentures (CDs) were randomly allocated into each group using computer software, and four interforaminal implants were inserted in parallel using a surgical guide. Three months after osseointegration, the patients received either CAD-CAM BioHPP framework hybrid prosthesis (Group I) or BioHPP bar supported and retained overdenture (Group II). Using digital preapical radiography, the bone loss is evaluated 6, 12, and 18 months after insertion. The subjective patient evaluation was done using a questionnaire based on the VAS includes five points for chewing, comfort, esthetics, speech, oral hygiene, and general satisfaction.

Results

The overall marginal bone loss (MBL) revealed that Group I (hybrid prosthesis) was more than Group II (bar overdenture) at all intervals in the anterior and posterior implants' mesial and distal surfaces. The patient satisfaction survey results showed that, after 18 months, the difference was statistically not significant between them all (P > 0.05) except for the comfort (for the overdenture group, 4.43 ± 0.53 while the fixed hybrid was 5.00 ± 0.00).

Conclusion

BioHPP framework material is an alternative material for implant rehabilitation of edentulous mandible with minimal MBL in BioHPP bar overdenture compared to BioHPP hybrid prosthesis.

Clinical outcomes of full-arch immediate fixed prostheses supported by two axial and two tilted implants: A retrospective cohort study with 12-15 years of follow-up

PURPOSE

To retrospectively assess clinical and radiographic outcomes of immediately loaded full-arch fixed prostheses supported by axial and tilted implants up to 15 years of function.

MATERIALS AND METHODS

Patients with one completely edentulous arch received an immediate full-arch fixed prosthesis supported by two anterior axial and two posterior tilted implants. Definitive prosthesis consisting of a CAD-CAM titanium framework and acrylic teeth was delivered 6 months later. Patients were regularly followed to assess clinical parameters and marginal bone level (MBL) change. Multilevel regression analysis was performed to investigate factors affecting implant failure and MBL.

RESULTS

Six hundred ninety-two implants were placed in 72 maxillae and 101 mandibles. Seven maxillary implants (5 axial and 2 tilted) in 6 patients and 12 mandibular implants (6 axial and 6 tilted) in 5 patients failed. 15-year cumulative implant survival was 97.51% and 96.91% in maxilla and mandible, respectively (p = .64). After 10 years, the difference in MBL between axial and tilted implants was not significant in the maxilla (p = .47, 65 patients), while it was in the mandible (p < .001, 80 patients). Significant higher bone loss was reported in the mandible at both 5- and 10-year follow-up (p < .001 and p = .004, respectively). Mixed-effect multilevel linear regression evidenced a correlation between arch and bone loss at 5- and 10-year follow-up, while no correlation was found with age, gender, smoking, diabetes, and history of periodontal disease.

CONCLUSION

This long-term study suggests that the present technique can be considered a viable treatment modality for the immediate rehabilitation of both maxilla and mandible.

Polyetheretherketone CAD-CAM framework for all-on-4 mandibular full arch prosthesis: Three years' retrospective study of periimplant soft tissue changes and ridge base relationship

PURPOSE

This study was conducted to evaluate the clinical peri-implant soft tissue changes during first year after occlusal loading and the ridge base relation after three years for mandibular CAD-CAM manufactured screw-retained implant-supported hybrid prosthesis of polyetheretherketone (PEEK) framework utilized with All-on-Four treatment concept.

MATERIAL AND METHODS

Sixteen completely edentulous patients were rehabilitated by 4 implants following the All-On-Four protocol. After 3 months, the definitive prosthesis was constructed to be a screw retained CAD-CAM milled framework from the modified PEEK (BioHPP), bonded to polymethylmethacrylate (PMMA) teeth and a pink shaded indirect light-polymerized nanofilled composite resin imitating the soft tissues. Peri-implant soft tissue changes regarding plaque, bleeding, gingival scores, and probing depth were evaluated at prosthesis insertion (T0), six months (T1) and 12 months (T2) after insertion. Also, monitoring of the ridge base relation was performed using cone beam computed tomography after one year (T0), two years (T1), and three years (T2) after mandibular fixed detachable All-on-Four framework insertion. Using Shapiro Wilk tests using SPSS^® software version 22 (SPSS Inc.), all clinical data were non- parametric while the ridge base relation data was parametric.

RESULTS

There were statistically significant differences regarding plaque, gingival, and bleeding scores for all implants with advancement of time. However, there was a statistically insignificant difference regarding probing depth in the posterior implants (p = .581). Regarding ridge base relation, there was a significant difference between observation times only in the anterior ridge area in between the two anterior implants (p = .011).

CONCLUSION

Within limitations of the study, the full arch PEEK framework of fixed-detachable, hybrid prosthesis used with All-on-Four concept for rehabilitation of mandibular edentulous arches is an acceptable treatment approach. Based on the stable ridge base relation posteriorly found in this study, less stress is distributed to the underlining bone due to the shock absorbing ability of PEEK. Special considerations for frequent soft tissue follow up and regular maintenance of oral hygiene measures are recommended. This article is protected by copyright. All rights reserved.

New generation CAD-CAM materials for implant-supported definitive frameworks fabricated by using subtractive technologies

Innovations in digital manufacturing enabled the fabrication of implant-supported fixed dental prostheses (ISFDPs) in a wide variety of recently introduced materials. Computer-aided design and computer-aided manufacturing (CAD-CAM) milling allows the fabrication of ISFDPs with high accuracy by reducing the fabrication steps of large-span frameworks. The longevity of ISFDPs depends on the overall mechanical properties of the framework material including its fit, and the physical properties of the veneering material and its bond with the framework. This comprehensive review summarizes the recent information on millable CAD-CAM framework materials such as pre-sintered soft alloys, fiber-reinforced composite resins, PEEK, and PEKK in high-performance polymer family, and 4Y-TZP. Even though promising results have been obtained with the use of new generation millable CAD-CAM materials for ISFDPs, clinical studies are lacking and future research should focus on the overall performance of these millable materials in both static and dynamic conditions.

Evaluation of Zirconia and High Performance Polymer Abutment Surface Roughness and Stress Concentration for Implant-Supported Fixed Dental Prostheses

Background: The High Performance Polymer is a based polymer biomaterial that was introduced as dental material to manufacture dentures superstructure and dental implants abutments. However, its surface characteristics and stress state still need to be properly described. The aim of this study was to compare the surface characteristics of a High Performance Polymer (Bio-HPP, Bredent, Senden, Germany) for computer-aided design and computer-aided manufacturing (CAD/CAM) milling and a Zirconia (Zirkonzahn, Steger, Ahrntal, Italy). Methods: The abutments surface roughness (Ra) was evaluated for each abutment material (N = 12) using a confocal laser microscope. Data were evaluated using One-Way ANOVA and Tukey tests (p < 0.05). In addition, a finite element analysis software was used to present stress measurement data as stress maps with 100 N loading. Results were generated according to Von-mises stress criteria and stress peaks were recorded from each structure. Results: Results showed a mean Ra of 0.221 ± 0.09 μm for Bio-HPP and 1.075 ± 0.24 μm for Zirconia. Both surface profiles presented a smooth characteristic regardless the measurement axis. The stress peaks from implant fixture and screw were not affected by the abutment material, however the high performance polymer showed the highest stress magnitude for the abutment region. Conclusions: Comparing the present results with the literature it is suggested that the CAD/CAM High Performance Polymer abutments present an adequate surface roughness with acceptable values of stress.

Influence of Framework Material and Posterior Implant Angulation in Full-Arch All-on-4 Implant-Supported Prosthesis Stress Concentration

This study evaluated the influence of distal implants angulation and framework material in the stress concentration of an All-on-4 full-arch prosthesis. A full-arch implant-supported prosthesis 3D model was created with different distal implant angulations and cantilever arms (30° with 10-mm cantilever; 45° with 10-mm cantilever and 45° with 6-mm cantilever) and framework materials (Cobalt–chrome [CoCr alloy], Yttria-stabilized tetragonal zirconia polycrystal [Y-TZP] and polyetheretherketone [PEEK]). Each solid was imported to computer-aided engineering software, and tetrahedral elements formed the mesh. Material properties were assigned to each solid with isotropic and homogeneous behavior. The contacts were considered bonded. A vertical load of 200 N was applied in the distal region of the cantilever arm, and stress was evaluated in Von Misses (σVM) for prosthesis components and the Maximum (σMAX) and Minimum (σMIN) Principal Stresses for the bone. Distal implants angled in 45° with a 10-mm cantilever arm showed the highest stress concentration for all structures with higher stress magnitudes when the PEEK framework was considered. However, distal implants angled in 45° with a 6-mm cantilever arm showed promising mechanical responses with the lowest stress peaks. For the All-on-4 concept, a 45° distal implants angulation is only beneficial if it is possible to reduce the cantilever’s length; otherwise, the use of 30° should be considered. Comparing with PEEK, the YTZP and CoCr concentrated stress in the framework structure, reducing the stress in the prosthetic screw.

Patient-Centered Treatment Outcomes with Full-Arch PEEK Rehabilitation Supported on Four Immediate or Conventionally Loaded Implants. A Randomized Clinical Trial

This study aims to assess the treatment outcomes (functional and subjective) of full-arch fixed hybrid rehabilitations made of PEEK (poly-ether-ether-ketone) with milled crowns of nano-filled composite (NFC) supported on four to six implants. In this randomized clinical trial, 34 edentate patients in the upper and/or the lower jaws were treated with the fixed hybrid dentures. In 16 patients (47.1% of the sample), the implants were loaded immediately (IL) by means of a provisional fixed rehabilitation made of PMMA (polymethylmethacrylate) screwed on Multi-Unit (MU) abutments connected after emplacement of the implant; however, in the counterparts (n = 18) these MU abutments were covered by healing caps and were left unloaded during two months (conventional loading protocol—CL), when all patients received a fixed hybrid PEEK-NFC rehabilitation on the upper and/or the lower jaw. Treatment outcomes were assessed 12 months after prostheses delivery. Functional outcomes were calculated according to masticatory performance, estimated by mixing ability tests of two colored chewing gums after ten chewing strokes, by the occlusal force/area recorded by pressure-sensitive sheets, and by electromyography of masseters and temporal muscles at maximum biteforce. The subjective outcomes of the treatment were assessed using both the oral satisfaction scale (visual analog scale) and the Spanish version of the Oral Health Impact Profile (OHIP-20). The findings of the present study showed that treatment with fixed PEEK-NFC hybrid prostheses significantly improved the masticatory performance, bite force, occlusal pattern, quality of life, and satisfaction, with the IL group being those with significantly higher occlusal bite forces and greater satisfaction in comparison with CL group. It should be concluded that PEEK-NFC hybrid prostheses can improve several patient-centered outcomes and that loading protocol significantly affects the patient’s self-rated satisfaction.

Trueness and marginal fit of implant-supported complete-arch fixed prosthesis frameworks made of high-performance polymers and titanium: An explorative in-vitro study

PURPOSE

To investigate the trueness and marginal fit of computer-aided design-computer-aided manufactured (CAD-CAM) complete-arch implant-supported screw-retained fixed prosthesis (CAISFP) made of polyetheretherketone (PEEK), polyetherketoneketone (PEKK) and titanium (Ti) MATERIAL AND METHODS: A typodont model with four implants, their multiunit abutments (MUAs), and MUA scanbodies were digitized by using a laboratory scanner. The generated CAD was used to mill CAISFP frameworks in Ti, PEEK, or PEKK (each n = 10). The frameworks were digitized with an industrial light scanner to superimpose resulting standard tessellation language (STL) file with the CAD file. Deviations at five points at the abutment-framework interface of each of the four abutment sites (1:left first molar, 2:left canine, 3:right canine, 4:right first molar sites) were calculated (trueness). Marginal gaps were measured using the triple scan technique. A nonparametric repeated measures ANOVA by Brunner and Puri with factors being abutment location and material was performed to assess the mean deviations for trueness and mean marginal gaps, followed by Mann-Whitney or exact Wilcoxon Signed-Rank tests (alpha=.05).

RESULTS

Material type significantly affected the trueness (p<0.0001). PEEK had the lowest deviations (0.039 +/-0.01mm) followed by PEKK (0,049 +/-0.009mm), and Ti (0.074 +/-0.011mm). For marginal gaps, only abutment location's effect was significant (p = 0.003). Within PEKK, gaps at abutment 4 were significantly larger, compared with abutments 2 (p = 0.04) and 3 (p = 0.02).

CONCLUSIONS

The trueness of PEEK, PEKK, and Ti frameworks was different after milled. PEEK had the highest trueness. However, the marginal fit of the frameworks was similar and smaller than 90 µm in average.

CLINICAL RELEVANCE

PEEK, PEKK, and Ti complete-arch frameworks had clinically acceptable gaps and may therefore be recommended when their fit is considered. Higher trueness after milling did not result in better marginal fit.

Evaluation of the surgical and prosthetic success of All-on-4 restorations: a retrospective cohort study of provisional vs. definitive immediate restorations

Background

All-on-4 concept allows an immediate restoration, which is frequently a provisional restoration (PR), and will be replaced by a definitive restoration (DR) a few months later. However, this approach involves much higher treatment efforts and costs, compared to a DR immediately after implantation. PRs were mostly incorporated in the introductory phase of the All-on-4 concept in our respective clinics. Today, PRs are only used for referred patients and bimaxillary restorations. The aim of the study was to investigate whether PRs and DRs have comparable success rates.

Methods

A total of 126 patients with 136 All-on-4 restorations supported by 544 implants were included in this retrospective cohort study. The observation period was 1 year. In 42 cases, a PR was placed initially and replaced by a DR 3 months later. In 94 cases, a DR was placed immediately. Biological, technical, and severe (loss of an implant or PR/DR) complications associated with PRs and DRs were compared. The absence of a serious complication was considered a success.

Results

A total of 27 patients were affected by 33 complications, 19 biological (2 PR and 17 DR) and 14 technical (6 in PR and 8 in DR) in the first 3 months. Eight patients had ten severe complications (1 PR and 9 DR). Severe complications were all implant losses. Implant survival rate was 98.2% (99.4% PR and 97.6 DR), and restoration survival rate was 94.4% (97.6% PR and 92.6% DR). Six out of the ten implant losses occurred in the posterior maxillae of male patients. After 3 months, ten complications occurred in six patients within 1 year. One of these complications was an implant loss in the posterior maxillae of a male patient.

Conclusion

PRs and DRs showed comparable complication rates during the observation period. Only in male patients did implant losses occur more frequently in the posterior maxilla.

Supplementary Information

The online version contains supplementary material available at 10.1186/s40729-021-00330-1.

The Effect of Different Cleaning Protocols of Polymer-Based Prosthetic Materials on the Behavior of Human Gingival Fibroblasts

Dental implant abutment and prosthetic materials, their surface treatment, and cleaning modalities are important factors for the formation of a peri-implant soft tissue seal and long-term stability of bone around the implant. This study aimed to investigate the influence of a polymeric material surface cleaning method on the surface roughness, water contact angle, and human gingival fibroblasts (HGF) proliferation. Polymeric materials tested: two types of milled polymethylmethacrylate (PMMA-Ker and PMMA-Bre), three-dimensionally (3D) printed polymethylmethacrylate (PMMA-3D), polyetheretherketone (PEEK), and polyetherketoneketone (PEKK). Titanium (Ti) and zirconia oxide ceramics (ZrO-HT) were used as positive controls. A conventional surface cleaning protocol (CCP) was compared to a multi-step research cleaning method (RCP). Application of the RCP method allowed to reduce S_a values in all groups from 0.14-0.28 µm to 0.08-0.17 µm (p < 0.05 in PMMA-Ker and PEEK groups). Moreover, the water contact angle increased in all groups from 74-91° to 83-101° (p < 0.05 in the PEKK group), except ZrO-HT-it was reduced from 98.7 ± 4.5° to 69.9 ± 6.4° (p < 0.05). CCP resulted in higher variability of HGF viability after 48 and 72 h. RCP application led to higher HGF viability in PMMA-3D and PEKK groups after 48 h, but lower for the PMMA-Ker group (p < 0.05). After 72 h, no significant differences in HGF viability between both cleaning methods were observed. It can be concluded that the cleaning method of the polymeric materials affected surface roughness, contact angle, and HGF viability at 48 h.